Solenoid valve made from stainless steel. Designed for glycol, water and air/co2. T.C. 34mm ports in both ends for maximum flexibility. Coil and plunger Italian-made by ACL. The valve can easily ble disassembled and cleaned.
Coil has DIN 43650 Type A connector (not included).
Normally used with T.C. 34mm to 3/8" NPT threaded adapter and leak-free quick connectors on one or both sides depending on setup.
Specifications:
Ports: TC34mm / TC34mm
Operation: NC (normally closed)
Power supply: DC24V, 10W
Orifice: Ø4.5mm
Pressure rating: Max 3 bar / 43 PSI
Due to high demand, this item is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this item to you when we receive more in early February.
34mm Tri-Clamp Tee.
ID: 19.2mm (DN20)
OD: 21.9mm
Length: 60mm
Due to high demand, this item is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this item to you when we receive more in late April.
Solenoid valve made from stainless steel. Designed for glycol, water and air/co2.
TC3mm ports in both ends for maximum flexibility.
Coil and plunger Italian-made by ACL.
The valve can easily ble disassembled and cleaned.
Coil has DIN 43650 Type A connector (not included).
Specifications:
Ports: TC 1.5" / TC 1.5"
Operation: NC (normally closed)
Power supply: DC24V, 10W
Orifice: Ø4.5mm
Pressure rating: Max 3 bar / 43 PSI
Submersible pump for cooling applications or similar.
A perfect match for FCS to supply cooling liquids to fermentation tanks up to 50 liters.
Very quiet.
Technical Information:
Voltage: 24VDC
Maximum Power: 17W
Maximum Flow: 11 L/min / 2.9 Gal/min
Maximum Height: 4.1m / 13.5 feet
Barb Size (liquid out): Ø=10.28 mm (recommended hose size: 8x12)
Ø=0.40" (recommended hose size: 5/16" ID)
Barb Size (liquid in): Ø=14.68 mm (recommended hose size: 10x14)
Ø=0.57" (recommended hose size: 3/8" ID)
IP rating: IP68
Cable: 3m / 9.8 ft.
Connector: LP12, 2-pin plug (male)
Removable bracket with 4 suction feet is included
Density sensor with integrated temperature sensor for FCS gives accurate and real-time density and temperature data for your fermentation tank
Measures density by inducing a vibration frequency in the fork and listening for the resonant frequency
Primarily designed for fermentation tanks like the F40-F300 and similar tanks
Tuning fork-based measurements gives accurate and real-time density and temperature data for your fermentation tank. The Brewtools density sensor measures density by inducing a vibration frequency in the fork and listening for the resonant frequency.
Take your fermentation to the next level with data-driven control and logging. Future updates of FCS will enable you to control temperature and pressure steps based on density in the tank, without the need for manual intervention.
This model is primarily designed for fermentation tanks like our F40-F300 and similar tanks. Accuracy may vary for smaller tanks (like MiniUni+).
More information: https://docs.brewtools.com/density-sensor
Specifications:
Density accuracy: +-0.002 SG
Temperature accuracy: +- 0.3ºC
Flange: TC 1.5". Ø25mm minimum
Length: 200mm from flange
Connector: LP12 5-pin (CAN bus + 24V)
Note: Accuracy and function can vary based on trub, yeast health, yeast flocculation, rapid temperature changes, dry-hopping and other additions and distance to tank wall/heating elements etc. Pressure fermentation can increase accuracy. Accuracy and features will improve over time with software updates.
Brewtools Product Number: 7713723
Coming soon! The Brewtools FCS Agitator is now available for pre-order. Place your order now and we will automatically ship it to you when it's available. The current estimated availability is early 2026.
Optimal Liquid Consistency: Magnetic-drive impeller evens out temperature gradients and maximizes hop utilization.
Smart Integration: Fully adjustable via FCS Display Module with support for automated interval mixing in future profiles.
Universal Compatibility: Fits most fermentation and brite tanks using tri-clamp adapters for flexible installation.
Agitator for FCS
Impeller based stirring system with magnetic drive for fermentation and brite tanks. The agitator mixes the liquid to even out temperature differences and can in many cases increase the utilization of hops and other additives. Speed is adjustable from the FCS Display Module. The agitator will also be able to be run at intervals in the upcoming advanced fermentation profiles in FCS.
The agitator can also be used without FCS with an adapter (BT1328) and a power supply (BT1324). The motor can be started with the button of top of the drive unit. Speed is controlled by pushing it multiple times and holding the button stops the motor.
Our agitator can be used on most fermentation and brite tanks with the help of adapters, as long as the impeller stays clear of the vertical wall.
Specifications:
Motor: Brushed DC motor, 500 RPM, 24V, 0.5A
Impeller material: POK, acid proof and food grade
Flange: TC 34mm. Ø19mm minimum
Length: 380mm / 14.9" from flange
Connector: LP12 5-pin (CAN bus + 24V)
Note: For F40 and other smaller tanks, it might be necessary to lift the agitator to avoid touching the cone wall using a tee or short pipe.
Coming soon! The Brewtools FCS Radar Level Sensor is now available for pre-order. Place your order now and we will automatically ship it to you when it's available. The current estimated availability is early 2026.
Precision Cone Measurement: High-accuracy radar technology tracks volume all the way down to the tank cone, eliminating guesswork during filling or packaging.
Rapid Calibration: Simplified setup process allows you to configure volume and dimensions quickly using a basic water-fill reference.
Direct-Mount Reliability: Optimized for vertical flange installation to ensure a clear signal path and maximum measurement stability.
Radar based level sensor for FCS
The days of guessing tank the volume during filling or kegging/bottling is over. Radar based level sensor designed to measure the tank volume down to the cone in a fermentation tank.
The sensor is configured by setting the volume, tank diameter and distance to the cone. It's easily done by filling water in the tank to the top of the cone.
The sensor must be installed on a vertical flange on the top of the tank, ideally on a single port welded on the curved top surface. Avoid using tees/pipes between the sensor and the tank.
Specifications:
Measuring distance: 0-3m / 0-9.8 ft. (Preliminary)
Flange: TC34mm. Ø19mm minimum
Connector: LP12 5-pin (CAN bus + 24V)
Note: During fermentation the krausen/foam will give incorrect values. Cooling spirals etc inside the tank may give incorrect readings.
The Brewtools DIY Power Cable is available for pre-order. Place your order now and we will automatically ship it to you when it becomes available. The current estimated availability is early 2026.
Power cable for FCS relay module (5A) or heaters.
Connector A: None
Connector B: LP20, 3-pin female plug
Color: Black
Length: 2m (6.5 ft.)
M24 Threads to 34mm T.C. Adapter.
For the MiniUni+, this adapter can be used to replace the Pressure Kit spunding valve with a 34mm T.C. Elbow to install the FCS spunding assembly.
M16 x 1.5mm inside threads for accessories.
Coming soon! The Brewtools LP12-2-Pin to LP12-5-Pin Adapter is now available for pre-order. Place your order now and we will automatically ship it to you when it's available. The current estimated availability is early 2026.
Adapter that allows connecting a power supply to a CAN device without FCS.
Connector A: LP12, 5-pin male plug (in-line connector)
Connector B: LP12, 5-pin female plug
Color: Black
Length: 0.1m
Coming soon! The Brewtools FCS Radar Level Sensor is now available for pre-order. Place your order now and we will automatically ship it to you when it's available. The current estimated availability is early 2026.
Precision Cone Measurement: High-accuracy radar technology tracks volume all the way down to the tank cone, eliminating guesswork during filling or packaging.
Rapid Calibration: Simplified setup process allows you to configure volume and dimensions quickly using a basic water-fill reference.
Direct-Mount Reliability: Optimized for vertical flange installation to ensure a clear signal path and maximum measurement stability.
Radar based level sensor for FCS
The days of guessing tank the volume during filling or kegging/bottling is over. Radar based level sensor designed to measure the tank volume down to the cone in a fermentation tank.
The sensor is configured by setting the volume, tank diameter and distance to the cone. It's easily done by filling water in the tank to the top of the cone.
The sensor must be installed on a vertical flange on the top of the tank, ideally on a single port welded on the curved top surface. Avoid using tees/pipes between the sensor and the tank.
Specifications:
Measuring distance: 0-3m / 0-9.8 ft (Preliminary)
Flange: TC 1.5". Ø19mm minimum
Connector: LP12 5-pin (CAN bus + 24V)
Note: During fermentation the krausen/foam will give incorrect values. Cooling spirals etc inside the tank may give incorrect readings.
The Brewtools Power Supply for Gas Release Solenoid Valve is available for pre-order. Place your order now and we will automatically ship it to you when it becomes available. The current estimated availability is early 2026.
24V, 40W Power supply with LP12 2-pin plug.
The Brewtools Type B Adapter for Gas Release Solenoid Valve is available for pre-order. Place your order now and we will automatically ship it to you when it becomes available. The current estimated availability is early 2026.
Cable for use between 2-pin cable and 24 VDC solenoid valves (gas).
Connector A: LP12, 2-pin male plug (in-line connector)
Connector B: DIN 43650 Form B
Color: Black
Length: 0.1m (3.9")
The Brewtools Gas Release Solenoid Valve is available for pre-order. Place your order now and we will automatically ship it to you when it becomes available. The current estimated availability is early 2026.
Solenoid valve made from stainless steel. Designed for air/co2.
TC3mm ports in both ends for maximum flexibility.
Coil and plunger Italian-made by ACL.
The valve can easily be disassembled and cleaned.
Coil has DIN 43650 Type B connector (not included).
Specifications:
Ports: TC34mm / TC34mm
Operation: NC (normally closed)
Power supply: DC24V, 6.5W
Orifice: Ø2.0mm
Pressure rating: Max 3 bar / 43 PSI
The Brewtools LP20-3-Pin Power Cable is available for pre-order. Place your order now and we will automatically ship it to you when it becomes available. The current estimated availability is early 2026.
Power cable for use between FCS relay module (5A) and sanitary heaters or water heater.
Connector A: LP20, 3-pin male plug
Connector B: LP20, 3-pin female plug
Color: Black
Length: 2m (6.5 ft.)
The Brewtools LP12-7-Pin Cable for Relay Modules is available for pre-order. Place your order now and we will automatically ship it to you when it becomes available. The current estimated availability is early 2026.
Cable for use between FCS I/O module and FCS relay module (5A).
Connector A: LP12, 7-pin male plug
Connector B: LP12, 7-pin female plug
Color: Black
Length: 3m (9.8 ft.)
The Brewtools FCS Relay Module is available for pre-order. Place your order now and we will automatically ship it to you when it becomes available. The current estimated availability is early 2026.
Relay Module for use with FCS. Specifically designed for small heating elements.
Control signal is 5V and the devices measures current draw.
The module has a 2-pole relay and several protective circuits for noise, over voltage etc.
For maximum safety, the device also has one fuse per phase.
Specifications:
110-240V AC, Max 5A
Power in: LP20 3-pin male
Power out: LP20 3-pin female
Signal: LP12 7-pin
Fuse: 2x 5x20 6.3A Fast Blow
Installation:
4 screw holes with 5mm diameter. Designed for countersunk screws.
