Need to de-gas a carboy full of wine? Say goodbye to swirling your wine for 10 minutes by hand! “The Whip” Wine Degasser will have it done in no time!
De-gas your wines quickly and easily with this lightweight, drill mounted degassing rod for wines. It features a plastic shaft with an offset ""hook"" for quickly degassing wines.
To use, mount the sanitized degassing rod on an electric drill. Insert through the neck of the carboy, and the slowly increase the speed of the drill. Reduce the speed or stop as the bubbles come out of solution. As the bubbles subside, you can begin again. Repeat until large amount of bubbles stop coming out of solution. Take care to keep the spinning wings submerged, you do not want to agitate the surface of the wine and oxidize it.
Lightweight inexpensive no more swirling for 10 minutes by hand!
Place underneath a carboy to tilt it and siphon every last drop sediment free. Keeps your hands free while you operate the siphon.
Be careful when using this product as the carboy can easily be tipped over. Using two can make a more stable setup.
Brewers love using refractometers for their ability to give quick, accurate readings with a small sample.
The HI 96811 Digital Refractometer is easy to use. Start by calibrating it with deionized or distilled water, then use a small sample from your brew to get a reading within seconds. Readings are displayed in degrees Brix, whch can easily be converted to Specifig Gravity.
Features:
Temperature: (in C or F) is displayed simultaneously with measurement on the large dual level display along with other helpful message codes.
Wide Range: The HI 96811 is versatile enough to fit most applications.
Easy Measurement: Place a few drops of the sample in the well and press the READ key.
Calibrate with Water: Fill the sample well with distilled or deionized water and press the ZERO key.
Automatic temperature Compensation (ATC)
Battery Operated: The HI 96811 is operated by a single 9V battery for portability.
Dual-level LCD: The dual-level LCD displays the measurement as well as temperature readings simultaneously.
Waterproof: The HI 96811 offers IP65 waterproof protection.
Quick, Precise Results: Readings are displayed in approximately 1.5 seconds.
Small Sample Size: The HI 96811 is able to read samples as small as 2 metric drops.
Range
0 to 50% Brix / 0 to 80C (32 to 176F)
Resolution
0.1% Brix / 0.1C (0.1F)
Accuracy
0.2 % Brix / 0.3C (0.5F)
Automatic Temperature Compensation
between 10 and 40C (50 - 104F)
Minimum Sample Volume
2 metric drops
Case Material
ABS
Battery Type / Life
(1) 9V / 5000 readings
Dimensions
19.2 cm (W) x 10.2 cm (D) x 6.7 cm (H)
Weigh
420g
This propane burner is the same as our H210 burner, but for low pressure propane applications. Twenty individual jets combine to produce heat that will boil your water or wort in a hurry. Should be installed and connected by a professional plumber. Flame height is 2 to 3". Ring Diameter is 8" the inlet thread is 1/2" Female Pipe Thread. 20 Jets.
This item is not intended for indoor use. These propane burners are not for use on portable propane tanks, they are for use with large propane tanks with regulators that typically feed rural homes where natural gas is not offered.
Our 3-piece thief is one of our most popular wine thieves. It can be taken apart into 3 sections for cleaning and sanitizing, then fit tightly together for taking samples. 27-1/2 inch length is ideal for taking samples from barrels, or other tall fermenters.
Designed for the small 'Nano' commercial brewery where the H315 series is too small but you don't yet need a full on expensive professional brewery pump. The March Nano Brewery Pump features a robust flow rate of 17 GPM with all the benefits brewers have come to expect from March magnetic drive pumps. Those features include the ability to throttle back flow and the use of food-grade materials where the beer is in contact with the pump.
*Please Note* - This pump must be taken apart and cleaned after every use to prevent the impeller from seizing. To do so, take the bolts out of the pump head, remove the pump head from the pump, then take the impeller shaft and actual impeller apart. Clean well, and reassemble.
Homebrewing Tips:
1. Great for Whirlpooling 20 gallons of wort or more.
2. Ideal for our Counterflow Chillers WC90.
Please note that the pump comes with a three foot cord WITHOUT a plug attached. It has a 16 gauge 3 wire setup.
Statistics
Motor: 1/8HP 110v/60Hz Max Flow: 17 G.P.M at zero head
Max Head: 27 ft. at 1 GPM
Inlet: 1" FPT
Outlet: 1/2" MPT
Materials in Contact with Beer
Polysulfone
Stainless Steel
Buna N
Ceramic
Our Ball Valves will last for years. Easy to clean. High grade 304-stainless made to last. 3/8" FPT on input and output side.
TIP: You can take a ball valve apart using two crescent wrenches. This will allow you to open up the valve to get to the ball and two gaskets that form the seal when closed.
If you're a brewer with an eye for detail, you’ll want to own this sight glass. The glass insert allows you to watch the flow of your beer during transfer.
Place this Tri-Clamp Sight Glass in-line when you transfer your wort from kettle to fermenter. It is great for monitoring flow and to see how your in-line oxygenator is flowing.
Made from 304-type stainless steel with Tri-Clamp ends. The maximum pressure is 150 PSI, about 10 bar.
H664 features 1.5" TC connections and a 1" ID flow path.
H664B features 1.5" TC connections and a 1.5" ID flow path
H664C features 2" TC connections and a 2" ID flow path
A metal shield that protects the thermometer, but still allows for easy reading. Loop on end of shield allows for convenient hanging. Fits both of our 12" glass thermometer (MT360A).
Precise hydrometer for measuring the sugar content and progress of fermentation in wine ferments. Comes with a thermometer/correction scale built-in. Please Note: Due to the large size of this hydrometer, it does not work with our standard 11" or 14" hydrometer jars. We recommend using our 500mL Graduated Cylinder (MT636D) with this hydrometer.
The beautiful Deconstructing Craft Beer poster is packed with information about the amazing beverage that is craft beer. From perception to ingredients, this poster textually and visually deconstructs craft beer in a way never seen before.
“Craft beer lovers are proud to hold a beer in their hands and admire and discuss the tastes, aromas and colors in their glass,” said Julia Herz, Craft Beer Program Director for the Brewers Association. ”Now those same beer lovers can proudly display their appreciation of craft beer with one of the most informative and beautiful posters on the topic.”
You’ll be seeing this poster in brewery taprooms and better beer bars across the country, and now you can proudly hang it on your wall.
Measures 24"x36"
This shortened malt pipe will enable our 50L Braumeister to brew 25L batches (from 10 gallons to 5 gallons). The way these Braumeisters function during the mashing stage, a smaller batch than 50L is usually not an option. By utilizing this shortened mash pipe, you can now brew either a 5 or 10 gallon batch with your 50L Braumeister!
This is a replacement assembly for our H315HF pump. It has the polysulfone head and the impeller as well. This unit is set up with the new impeller, and will replace the head of an H315HF unit, or upgrade an older H315 to the High Flow model.
Replacement Lock Nut for our Stainless Steel Weldess Bulkhead Kits.
Please Note: These lock nuts are not standard size NPT and will only work with our Weldless Bulkhead Kits.
When you want to customize your own setup, it’s good to have the right fitting on hand.
This stainless steel compression fitting gives you the versatility to put your setup together in the way that works best for you.
304-Type Stainless Steel compression fitting.
1/2" Comp. x 1/2" FPT
This is a Stainless Steel one way Check Valve. It has 2" T.C. Fittings on either side, and releases pressure at ~1 p.s.i.
Can be used to inhibit a siphon in certain applications, or to vent gas pressure in a tank.
Produce even tastier beers with your Speidel Braumeister by limiting oxygen exposure during the brewing process. Exposure to oxygen in the brewing process can impact the flavor of the final beer and negatively affect the flavor retention and shelf life. This is especially crucial for lighter, malt-forward beers that have less hops, such as lagers, pilsners and wheat beers. With the Low Oxygen kit you can minimize oxygen exposure during mashing, cooling, and transferring to your fermenter. Make the malt character in your beers shine brighter and last longer!
Accessory kit for Low Oxygen Brewing with the Braumeister 20 L
Limits oxygen exposure during mashing (and cooling for BM-Plus users)
The higher fixed filter plate allows for more malt -- up to about 15.5 lbs
Includes swimming lid, support ring for filter plate and fixing nut
Half Coupler with 1/2" Female Pipe Thread. Half couplers have thread for insertion from one side only. 304 stainless. Weld into place. You will need to punch a 7/8" hole to install.
Produce even tastier beers with your Speidel Braumeister by limiting oxygen exposure during the brewing process. Exposure to oxygen in the brewing process can impact the flavor of the final beer and negatively affect the flavor retention and shelf life. This is especially crucial for lighter, malt-forward beers that are lightly hopped, such as lagers, pilsners and wheat beers. With the Low Oxygen kit you can minimize oxygen exposure during mashing, cooling, and transferring to your fermenter. Make the malt character in your beers shine brighter and last longer!
Accessory kit for Low Oxygen Brewing with the Braumeister 50 L
Limits oxygen exposure during mashing (and cooling for BM-Plus users)
The higher fixed filter plate allows for more malt -- up to about 33 lbs
Includes swimming lid, support ring for filter plate and fixing nut
Speidel 1" DIN to 1.5" TC adapter. If you have a mixture of TC and DIN fittings, there is finally an adapter to help you connect everything together. To top it all off it is made with the expert craftmanship of Speidel.
Our Ball Valves will last for years. Easy to clean. High grade 304-stainless made to last. 1" FPT on input and output side.
TIP: You can take a ball valve apart using two crescent wrenches. This will allow you to open up the valve to get to the ball and two gaskets that form the seal when closed.
Please Note: the ball valve may be difficult to turn at first, but it will become less resistant after it is rotated back and forth a couple times.
The H205 55,000 burners come with 90 degree angle jets. These work great with a flexible gas line hook up. However, in some hard piped applications a straight jet is needed, so we made one. Threads directly into burner. We use them on our systems
This Duotight fitting with 1/4" Flare is perfect for flared gas ball lock and pin lock disconnects. Can also be used to connect gas line to the flare fitting found on the KOMOS® CO2 Regulator. Compatible with EVABarrier 9.5 mm OD tubing (D1719). Although this fitting would also fit a beverage disconnect, 9.5 mm OD EVABarrier is only recommended for beverage line in long draw draft set ups. The Duotight fitting does not require a flare washer. See the instructions below for how to ensure a leak-free connection when attaching to flare fittings. Duotight fittings are high-quality push-in fittings that seal tight and offer superior sealing capacity due to the double O-ring sealing design. High Performance Double O-Ring Design:
The secret to Duotight’s superior sealing performance comes from the fact that they use not one, but two high-quality EPDM O-rings. The double O-ring means they have literally twice the sealing surface when compared with other push-in fittings. This makes them more reliable and significantly reduces the chance of leakage. The double O-ring system also means that tubing can be bent at a much tighter radius without causing leaking issues, which can be an issue with other fittings. This combination of factors makes Duotight the most reliable push-in fittings on the market. EPDM offers excellent chemical resistance for a longer life span. When compared with silicone and vinyl, EPDM has much better gas transmission rates, better wear resistance, and is BPA-free. No Clamps Necessary!
We recommend cutting your tubing straight, not on an angle, to ensure the line forms a complete seal. To remove the fitting simply push in the collet and the hose can be removed. Features:
Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. Kegland Part number: KL11037
Who doesn't like a faster brew day? Help your 50L Braumeister get up to strike temp and to a boil faster; and use less energy to maintain the boil with this neoprene sleeve from Speidel. Fits both new models as well as pre-2015 models.
If you like to use whole cone hops with your Braumeister this is a great way to prevent clogs and stop some of the larger pieces of hops from getting into your beer. This hop sieve is built for the Braumeister 20 and 50 liter systems and fits right over the outlet tap.
Justin Crossley (The Brewing Network) and Matt Brynildson (Firestone Walker) discuss the "Perfect American Pale Ale" in a very informative brewing session. During their brew day, Matt walks us through brewing the Pale 31 kit, while Justin keeps us laughing (as always).
From modifying your water, to choosing your grain and hops, to showing you how to use them properly; this DVD has it all. Not to mention the special features which include: A tour of the new Firestone Walker Brewery, a tour of the MoreBeer! Full Digital BrewSculpture with MoreBeer!'s Chris Graham, making a yeast starter with Doc, and more!
This is a premium black neoprene jacket, tailor-made for the 1 bbl MB Conical Fermenter. Made from 6mm neoprene with black fabric on both sides. Perfect for insulating the conical and using alongside our Reactor Rods.
