CO2 tanks & regulators are essential pieces of equipment for kegging and dispensing your homebrew. Using a CO2 regulator to carbonate your beer exactly to the preferred carbonation level is an easy way to improve your homebrew. CO2 can be used to not only force carbonate but also push your beer from the fermenter into the keg, as well purge the keg of oxygen before filling it. We offer multiple sizes of CO2 tanks, as well as many different CO2 regulators, manifolds and CO2 splitters.
Serve beer on tap at home! A quality CO2 tank is a core component to any home draft system.
Made from high-quality aluminum that will never rust like steel tanks
Dispense up to 50 x five-gallon kegs of homebrew
CGA320 valve pairs with standard US-style CO2 gas regulators
KOMOS® offers a full suite of first-rate draft products and draft fittings—from kegs to faucets and everything in between!
This size is large enough for commerical applications—it should last you a while on your home draft system
Brand new aluminum 25 lb CO2 tank made from high strength aluminum alloy and high quality CGA320 valves. Because it is made of aluminum rather than steel you can feel confident that it won’t rust. It’s called a 25 lb tank because it holds 25 lbs of compressed (liquified) CO2. 25 lbs of CO2 is enough to dispense about 50x 5-gallon kegs of homebrew.
Aluminum tanks are superior to steel because they do not rust. All tanks are shipped empty. To have tanks filled you will want to visit your local welding supply shop. Because you are purchasing a new tank you can choose to either have it filled or to exchange it for a filled tank at your local gas supplier. If you have this tank filled the local gas supplier is responsible for affixing the correct neck label that identifies the gas being put in the cylinder.
Tanks should always be stored in an upright position.
Features:
Made from corrosion resistant, engineered Aluminum
Brushed finish
Thick, durable cylinder walls
32.5" T x 8 Ø
DOT approved
New high quality CGA-320 valve
Light weight compared to steel tanks
This stainless pressure relief valve offers precise control and easy to adjust. The elongated body provides room for a taller spring to make small adjustments more accurate. Tune in the pressure setting from 0 to 30 psi using the knurled adjustment knob. 1/4" male pipe thread.
The Taprite beer carbonation tester is designed to be used in the field to verify carbonation levels during equipment installation and keg change-outs. It is a cost effective and accurate tool for troubleshooting and quality control. The carbonation tester's sturdy, 11-ounce acrylic canister includes a handy label noting the appropriate CO2 volume based on your temperature and pressure reading. The tester's cap and fittings are made of lightweight metal with easy to grip knurling. The pressure gauge includes a protective rubber boot (600gps-01) for additional durability. Taprite's beer carbonation tester is easy to handle, easy to use, and easy to clean. Each tester comes with a cushioned carrying case, as well as inlet and outlet hoses with quick disconnects.
Taprite Part Number: 2701-bct
This 3-way stainless steel tee is perfect for splitting gas lines to push multiple kegs with one CO2 cylinder. Slightly oversized at 10 mm OD (0.39") for a tighter fit with 3/8" ID tubing.
Over time the internal diaphragm can wear out and result in drifting pressure or a slow leak through the regulator body. Replacing the diaphragm is usually the best path to the fixing these issues so your regulator can return to holding consistent pressures. Compatible with both the single and dual-body KOMOS regulators.
Contains the o-rings for the piston, the red inlet washer, MK4 seat assembly o-ring, 2 x barb MFL outlet o-rings and a thumb screw o-ring.
For instructions on replacing the seals and/or general maintenance please refer to the product manual below.
KegLand Part Number: KL12584
Use this quick disconnect set to seal a soda bottle under CO2 pressure. An ideal way to bring homebrew to a party without all the accessories.
TIP N' TRICK: Add a CO2 tee inline with your current CO2 setup and install the H481 Kent Shut-Off Female QD w/ 1/4 in Barb included. This way you always have access to CO2 accessible to put your beer under pressure before leaving for the party.
* A single-handed connection and disconnection
* Strong plastic that can handle 250 degrees, very durable, and is medical-grade compliant and made from FDA approved material
* Easy installation into your home brewery
* KENT Systems quarter turn design functions safely
Here at the shop, many of us plan on using these nitrogen cartridges to push wine out of 5 gallon soda kegs, since the nitrogen does not go into solution. You could also use them in beer situations where you want to push out but not carbonate. Please be aware that the nitrogen will only fill 20% of the space that a 12g CO2 cartridge will because Nitrogen exerts a lower partial pressure than CO2.
Nitrogen has a higher PSI than CO2 so these cartridges will not work with CO2 Mini Regulators.
Please note: due to air shipping restrictions, this product is only eligible for ground shipment within the contiguous United States.
This super handy Solenoid Valve is compatible with 1/4" or 6.35 mm OD PE Water Line or EVABarrier tubing. This size tubing is often used on water filtering systems or reverse osmosis systems, and can be used with an Inline Regulator to drop your mains water pressure if needed.
Unlike some other solenoid valves this is a direct acting solenoid valve meaning the solenoid valve can go down to 0 pressure. This makes it quite handy for controlling CO2 flow or other low-pressure gasses. Suitable for pressures up to 115 psi (8 bar) so it will handle water pressure with no problem at all.
Made from high-quality metal and POM engineering plastics so it is durable and suitable for contact with a wide range of chemicals and beverages.
Specs:
Inlet/Outlet: 6.35 mm (1/4")
Pressure Rating: 0-115 psi (0-8 Bar)
Mode: Normally Closed (NC)
Solenoid Coil Voltage: 12V
Solenoid Coil Amp Draw: 1.1A
KegLand Part Number: KL09478
This replacement spring is intended for use with our adjustable stainless steeel pressure relief valve - D1832L & D1833L. These units are adjustable from 0 to 30 psi.
Example photo shown. The spring you receive may not match the photo exactly.
Use this cap to seal a soda bottle under CO2 pressure. An ideal way to bring homebrew to a party without all the accessories.
TIP N' TRICK: Add a CO2 tee inline with your current CO2 setup and install our H481 Kent Shut-Off Female QD w/ 1/4 in Barb. This way you always have access to CO2 accessible to put your beer under pressure before leaving for the party.
* A single-handed connection and disconnection
* Strong plastic that can handle 250 degrees, very durable, and is medical-grade compliant and made from FDA approved material
* Easy installation into your home brewery
* KENT Systems quarter turn design functions safely regardless of pressure up to 125 p.s.i.
This adapter piece enables legacy Torpedo Mini CO2 Regulators (KEG965A) to be compatible with 74g CO2 cartridges that have a small unthreaded gap at the top of the neck—cartridges similar to KEG969.
This piece now comes standard on the updated Torpedo Mini CO2 Regulator and is a direct replacement part for KEG965B.
Leave your bulky CO2 regulator and cylinder at home!
This Mini CO2 regulator uses 74g cartridges for convenient mobile draft dispensing
Dial in your ideal serving pressure just as you would with your standard regulator
A portable mini-regulator with all the features of a full sized regulator! Perfect for parties and gatherings where you don’t want to haul around a large canister and hoses. A lot of great features packed into a very small package.
The regulator has a range of .5-1.5 bars (7-21 psi). This means that, unlike a button-activated CO2 injector that shoots in CO2 at a fixed pressure, the mini-reg allows you precisely dial in pressure and keep it there. It utilizes a disposable 74 gram CO2 cartridge, which is the largest size that can be shipped full. This is a two stage mini-regulator, meaning that it takes the pressure down from 800 psi (cartridge pressure) to a lower pressure and then to your set pressure of around 10 psi. Two stage regulators are the only way to have consistent pressure. One 74 gram cartridge will typically dispense one 5 gallon keg.
This is the regulator only. Cartridges and quick disconnect (KEG730) sold separately.
Please Note:
This product is only eligible for ground shipment in the Contiguous United States. No air shipment or shipment to Hawaii or Alaska.
The mini CO2 regulator does not have an internal check valve. To add a check valve use the regulator with KEG729 or KEG741.
3/8-24 UNF x TR21-4 adapter ring for the KegLand Core 360 Mini CO2 Regulator. Suitable for 16 g CO2 cartridges. This is a replacement standard ring that is included with the regulator.
An adjustable pressure relieve valve with a range from 0 to 30 psi. Made from stainless steel this is non-threaded and designed to be welded in place.
For a 1/4" MPT option see D1833L.
Use this quick disconnect to seal a soda bottle under CO2 pressure using our H470-Kent Shut-Off Male QD - Soda Bottle Cap. An ideal way to bring homebrew to a party without all the accessories.
TIP N' TRICK: Add a CO2 tee inline with your current CO2 setup and install this H481 Kent Shut-Off Female QD w/ 1/4 in Barb. This way you always have access to CO2 accessible to put your beer under pressure before leaving for the party.
* A single-handed connection and disconnection
* Strong plastic that can handle 250 degrees, very durable, and is medical-grade compliant and made from FDA approved material
* Easy installation into your home brewery
* KENT Systems quarter turn design functions safely regardless of pressure up to 125 p.s.i.
The CMBecker Inline Flow Control 4mm Barb is necessary for those looking to use tubing that has an inner diameter of 3/16"
Use with CMBecker In-Line Flow Control Compensator
Stainless steel nipple, only stainless steel touches your beverage
Works with CMBecker International shanks.
Includes CMBecker beer nut
The size is 4mm. When using with 3/16" hose you may need to slightly heat hose (using hot water) to stretch hose over barb (this is how we do it!) Just make sure you clamp it properly to get a good seal
This will not work with a standard shank, it works with CMBecker shanks. These seal at two places and do not have a flat end (see photo)
The CMBecker Inline Flow Control 7mm Barb is necessary for those looking to use tubing that has an inner diameter of 5/16 or 3/8"
Use with CMBecker In-Line Flow Control Compensator
Stainless steel nipple, only stainless steel touches your beverage
Works with CMBecker International shanks.
Includes CMBecker beer nut
The size is 7mm which is slightly wider than 1/4" at 0.27"
This will not work with a standard shank, it works with CMBecker shanks.
The CMBecker International Inline Flow Control 10mm Barb is necessary for those looking to use tubing that has an inner diameter of 3/8". It is slightly smaller than 1/2", but it will fit a 1/2" ID Hose if properly clamped.
Use with CMBecker In-Line Flow Control Compensator
Stainless steel nipple, only stainless steel touches your beverage
Works with CMBecker International shanks.
Includes CMBecker beer nut
The size is 10mm which is between 1/2" and 3/8". When using with 3/8" hose you may need to slightly heat hose (using hot water) to stretch hose over barb (this is how we do it!) When using with 1/2" it will be loose, but we have used it with syphon hose and thicker high heat (EJ beverage or silicone) hose. Just make sure you clamp it properly to get a good seal.
This will not work with a standard shank, it works with CMBecker shanks
