Brew Kettles, Burners & Accessories

Ready to dive into distilling, but unsure how to piece together your home still? Check out these complete systems that will set you on the path to producing high quality spirits. This kit comes with the 35L DigiBoil Electric Kettle and the Copper Pot Still Condenser. The Copper Pot Still is perfect when you want the flavor of the wash to come through, whereas a reflux still is more favorable for producing pure, unflavored spirits. If you want to make whiskeys and gins, this pot still top is a great way to start! The classic "V" shape captures the vital esters, aldehydes, and phenolic compounds that are necessary for the complex spirits such as whiskeys and gins. Made from solid copper. When your hot spirit comes into contact with the copper, the copper acts like a catalytic converter to drive sulfur out of the spirit. This leads to less off-flavors and higher quality spirit.  Kit Includes: 35L DigiBoil Gen 2 (110V or 220V) 110V / 15A power and plug (5 ft. cord) 220V / 15A power NEMA 6-15 plug (5 ft. cord) Copper Reflux Still Condenser w/ Barb Connections 13 mm Inlet/Outlet Barbs (0.51 in.) Distillation Lid & Gasket Set of Adjustable Lid Clamps   Warning: Distilling alcohol without permits or licensing is illegal in many countries, including the United States.  It is the customer's responsibility to research their local, state, and federal laws and abide by those laws. Brewmaster is not responsible for any damage or injury caused by either misuse or unlawful use. Stills can also be used to produce essential oils, vinegar, purified water and engine fuel (requires permit in USA). 

Read more less

Use this lid along with the 35L BrewZilla or DigiBoil and a copper still top (DS120 or DS130) to make your own easy-to-use distillery. This lid has a 1.85" (47mm) hole for the still top. Lid gasket included. Note: This lid uses a 6mm gasket to better fit the Gen 4 BrewZilla and Gen 2 DigiBoil. It is also backwards compatible with Gen 3 and older BrewZillas and Gen 1 DigiBoils. To improve the seal further, we highly recommend using the Adjustable Lid Clamps with the Distillation Lid if your unit does not have them. Made from 304 stainless steel Measures 12.25" in diameter. Kegland Part number: KL03483

Read more less

The Copper Reflux Still Condenser is designed to create high percentage pure neutral spirit.  It features a flow management device, which makes it extremely easy to use. No need to worry about fine tuning the water flow speed. As long as your providing enough coolant or cold water running through the condenser, the flow rate doesn't matter. The purity of the spirit can be controlled by two included flow control inserts. These brass inserts come with a 1.0mm hole and 0.6mm hole. As the hole gets smaller, the rate at which the spirit exits the condenser will decrease, thus increasing your reflux ratio and the purity of your spirit. If you want to make whiskeys and gins we recommend checking out the Copper Pot Still! This is only the still top and does not come with a boiler. Combine with a distillation lid to use a BrewZilla or DigiBoil as the base for this Alcoengine brand still top. Comes with 13 mm (0.51") barb connections for the water inlet and outlet.   Kegland Part number: KL16162  

Read more less

Welded 1.5" tri-clamp ports for a lifetime of leak-free use 304 stainless steel construction with mirror polish finish Front and back located handles with silicone grips Induction burner compatible Notched lid provides cover while not interfering with immersion chillers, hop bags, or other accessories The BrewBuilt Pro Brewing Kettle is built for even more versatility than the standard T.C. kettle. A third tri-clamp port is offset from the front and ready to accept an electric heating element, whirlpool return valve, or any other accessory that you want to incorporate with the kettle. Handles are located at the front and back, rather than either side, saving you space when building out a horizontal system and will keep fittings pointed away from you regardless of which side you pick up the kettle from. Designed for Brewing. Built to Last. BrewBuilt brew kettles are made from 304 stainless steel and offer an unparalleled mix of features for the price. At the very top of the list are three welded-in place tri-clamp couplers that offer a lifetime of leak free use.  As you can imagine, welding in a coupler costs more than punching a hole and using a gasketed (i.e. weld-less) fitting. Welded fittings offer a permanent connection that to us is worth every penny.  The second unique feature that we absolutely love about these brew kettles is the notched lid with silicone plug.  This notch allows you so much flexibility; you can use an immersion chiller, one of our Ultimate Sparge Arms for mashing, tie off hop bags, take a temp reading during cooling, or whatever else we all can dream up.   Our T.C. kettles were designed to keep pace with the ever-evolving world of brewing technology. Tri-clamp fittings are standard fare in professional breweries, and they’ve been widely adopted in homebrewing as T.C. fermenters and pumps become more affordable and widely available. Tri-clamp fittings, also known as Tri-clover, allow you to make a sanitary connection that is free of nooks and crannies for contaminants to take hold. They are much easier to break down for cleaning compared to threaded connections, and they don’t require Teflon tape to make a watertight seal. T.C. fittings and accessories also give you the distinct advantage of being able to clean in place (CIP), so you don’t need to break down your entire system after every brew day.   This kettle comes without fittings so you can modify it with whatever tri-clamp accessories best suit your needs.   This Brew Kettle has a lot to offer... Some other features we dig include the internal volume markers from the bottom to the top - so handy for instant reads.  The silicone sleeved handles on the kettle and the lid are a cool feature to protect your hands. The tri-clad bottom with a 4mm core of aluminum sandwiched between two layers of stainless steel offers even heat distribution during the boil and also makes it a perfect choice for anyone wanting to use an induction burner.  The bottom coupler is also cool with 1/2" male threads on the outside and 1/2'' female threads on the inside.     Beefy 304 Stainless These kettles are made from 304 grade stainless.  That means you will have less corrosion issues than with a kettle made from lower grade 201 type stainless. We put these kettles through a corrosive salt water test in the MoreBeer! shop and they passed with flying colors. We also made sure the rivets and riveted handles were also made of stainless steel for a long term, trouble free life.  The 10 and 15 gallon size are made from 1.0mm thick stainless steel. The 20, 30 and 50 gallon size are made with 1.2mm stainless - that's pretty thick stuff - and you will know it when you pick one up. The included ball valve is a two piece design that allows for easy cleaning (we prefer these over 3 piece for ease of assembly) and is also made from 304 stainless.    Mirror Polish Finish The mirror polish finish isn’t just for making your Instagram feed pop! This extra slick finish is much easier to clean and sanitize than a standard brushed stainless kettle. Hop trub and other organic solids left behind after a brew day will have a hard time clinging to the interior surface and scrub away with ease.   Size Ratios and Stuff All the BrewBuilt kettles follow the recent trend to a 1.2:1 ratio where the height is 1.2 times the diameter. This is a proven commercial ratio that has been adopted in homebrewing to achieve a more consistent 10% evaporation rate during the boil.  We do like this ratio for boiling. For Mashing we would prefer a little bit shallower but that is a small compromise. Dimensions for a hot-liquor tank, if you are thinking brewing system down the road, are irrelevant as any ratio kettle will do.     Final Words With welded tri-clamp fittings, mirror polish finish, a bunch of cool features, and a solid, thick 304 stainless steel core this kettle is a pretty amazing value. Remember, if you order from MoreBeer! we ship free anywhere in the continental USA!   Features: Three welded T.C. couplers for a lifetime of leak free use Notched lid with silicone plug for flexibility 304 Stainless construction for longevity 1.0mm (10 & 15 gal) or 1.2mm (20, 30 & 50 gal) thick side walls resist denting 4mm Tri-Clad Aluminum bottom sandwiched between two layers of stainless steel for no scorching Internally etched volume markers from top to bottom for easy reading Silicone coated handles for heat protection 1.2:1 Ratio is optimal for boiling evaporation rate Lid is designed to conveniently hang from a handle  Stainless handles with stainless rivets for secure lifting     SKU Size Kettle ID (in.) Height (in.) BE581 10 13.78 16.54 BE582 15 15.75 18.90 BE583 20 17.72 21.26 BE584 30 19.69 23.62 BE585 50 23.62 28.30   Lowest Price Guarantee, this item has MAP pricing so you can be confident you won't find it for less.

Read more less

If you prefer a hoppy beer, you’re likely concerned with keeping the hops in your boil kettle and out of your fermenter during your home brewing. The Blichmann Hop Blocker is a handy brewing accessory that promises to keep those hops out of the fermenter and securely in the boil kettle, all without disrupting the rest of the brewing process.   Through rigorous and repetitive testing, Blichmann Engineering has determined that the 90 percent to 95 percent of the hop material is left behind when using the Blichmann Hop Blocker to transfer your brew to the fermenter. While many traditional screen filters draw from the bottom of the kettle and often plug the screen, the Hop Blocker drains the majority of the wort from the top down, enabling the hops and trub to settle undisturbed at the bottom of the kettle. The filter works on just a small portion of the wort instead of the entire thing, making it much less disruptive.   The Blichmann Hop Blocker is designed for use with pellet hops only, not with whole, loose hops, as those could clog the Hop Blocker.  

Read more less

The Gen 2 DigiBoil features two distinct updates that are not currently pictured in the primary images. The stainless steel lid has been upgraded to a glass lid, allowing you to observe and monitor boil activity. The rubber feet have been replaced with a plastic base that provides improved stability and slightly raises the unit for better ground clearance. Updated images coming soon. The most affordable all-in-one automated all-grain brewing system! Mash grains and boil wort in a single vessel External pump kit for recirculating mash will improve efficiency, consistency, and clarity DigiBoil electric kettle automatically maintains mash temperatures with the digital controller Dual heating elements combine for 1500W of power The DigiMash system represents the best value in electric all-grain brewing you'll find. With a 9-gallon DigiBoil electric kettle and the DigiMash stainless steel mashing accessory pack included, this is by far the most affordable way to get into electric all-grain brewing. It may not have all the bells and whistles of the BrewZilla, but it does have everything you need to mash and boil all in one unit. With the Recirculation Pump Kit, you can recirculate sweet wort during the mash to improve starch conversion, maintain a consistent temperature throughout the mash, and improve the clarity. The pump can also be used to move water around your brewery if you use a secondary vessel to hold sparge water, or to transfer the wort from your kettle to your fermenter. With the optional Whirlpool Arm, you can also swap out the Recirculation Arm and use your pump kit to whirlpool after the boil. If you're deciding between the DigiMash and the BrewZilla, there are a couple of key differences worth noting. One of our favorite features of the BrewZilla is the programmable mash steps and delayed start, which the DigiMash does not have. You can still step mash by simply raising the temperature manually on the controller, but the automatic steps are a convenient feature if you want to set it and forget it. One advantage that this setup has over the BrewZilla is that the pump is external. This makes cleaning and fixing pump issues much easier, as you can quickly take apart the pump head to clean and clear out residual gunk at the end of each brew day. This model comes with the 35L DigiBoil, which has two built-in heating elements that run off a 110V plug. One element is 1000w and the other is 500w for a combined 1500 watts! The elements can be individually controlled, allowing you to use a single element to gently hold temperatures, or engage both elements to quickly go from mash temp to boiling. Temperatures are set and automatically maintained through the digital control panel. Simply set your desired temperature and flip on the heating element(s).  DigiBoil Features: 304 stainless steel construction 9-gallon total capacity Digital temperature control 110V / 15A power and plug (5 ft. cord) Dual heating element control (1000w and 500w) Heating elements are concealed for easy cleaning 304 stainless steel 1/2" ball valve with 13mm barb (approx. 1/2") Stamped-in volume markers (gallons & liters) Stainless lid Temperature reads in °F or °C With elements turned off, hold both +/- buttons to switch between °F or °C Recommended max. grain bill - 18 lbs Recommended min. grain bill - 8 lbs External Dimensions: 29" H x 15" W (including handles) Internal Dimensions: 19.5" H x 11.75" W DigiMash Stainless Steel Accessory Pack Includes: False bottom Malt pipe Wire support  Malt pipe handle Malt pipe bottom screen Recirculation Pump Kit Includes: High temp magnetic drive pump Recirculation arm with male camlock Female camlock with barb fitting 1/2" FPT x 1/2" barb fitting 1/2" MPT x 5/8" barb fitting 1/2" ball valve 5 ft. length of silicone tubing 4 x hose clamps Plumber's tape  

Read more less

Anvil Brewing Equipment brew kettles are as durable as they get, with the 5.5 gal version fitting well on a stovetop and the larger versions sitting nicely on the Anvil high performance burner. This rugged kettle is constructed from high quality materials and is designed for a lifetime of demanding use.   Standard Features Include:   -Heavy 18 gauge 304 stainless steel with reinforced lip for durability and easy cleaning. -Induction capable tri-ply clad bottom. -Internal etched level graduations in gal and liters for accurate measurements -A dual scale F/C thermometer – included standard! -Solid cast stainless steel handles for comfort and durability – no rivets to leak or harbor contaminations! -Lid conveniently rests on kettle handle -Ideal 1.2 height to diameter ratio for optimum brewing performance -Purpose built stainless steel ball valve with integral bulkhead seal is rock solid, easy to install and disassemble, and will never leak. -Dip tube drains to within 3/8” of the bottom of the kettle.   Anvil Brewing Equipment provides everything you need in a brew kettle! But if you want more, add a boil kettle strainer for the ultimate in hop and trub filtration or convert your Anvil Brew Kettle to a mash tun with our optional perforated false bottom.   SKU Size Kettle ID (in.) Height (in.) BE340 5.5 12 11.625 BE341 7.5 12.75 14 BE342 10 13.75 16.75 BE343 15 16 19 BE344 20 17.75 21.25   Lowest Price Guarantee, this item has MAP pricing so you can be confident you won't find it for less.

Read more less

Perfect for 5 to 20 gallon batch sizes. 3 7/8'' wide at the widest point. You will need our high-pressure, adjustable pressure regulator to operate burner. This is a ring style burner and not a jet burner. The flame distribution and control is great and not concentrated like a jet burner. Will not work with low pressure propane (house propane) or with natural gas. Ideally you want to install these about 4-6 inches below the kettle. These burners do not come with a brass jet. If you need the brass jet for attaching regulator tubing with flare outputs please purchase the H205J. If you intend on plumbing these you will need either a GSS008 or H233 to connect to your gas system. These item is not intended for indoor use.

Read more less

Ready to dive into distilling, but unsure how to piece together your home still? Check out these complete systems that will set you on the path to producing high quality spirits. This kit comes with the 35L DigiBoil Electric Kettle and the Copper Reflux Still Condenser. The Copper Reflux Still Condenser is designed to create high percentage pure neutral spirit.  It features a flow management device, which makes it extremely easy to use. No need to worry about fine tuning the water flow speed. As long as your providing enough coolant or cold water running through the condenser, the flow rate doesn't matter. The purity of the spirit can be controlled by two included flow control inserts. These brass inserts come with a 1.0mm hole and 0.6mm hole. As the hole gets smaller, the rate at which the spirit exits the condenser will decrease, thus increasing your reflux ratio and the purity of your spirit. If you want to make whiskeys and gins we recommend checking out the pot still kit! Made from solid copper. When your hot spirit comes into contact with the copper, the copper acts like a catalytic converter to drive sulfur out of the spirit. This leads to less off-flavors and higher quality spirit.  Kit Includes: 35L DigiBoil Gen 2 (110V or 220V) Copper Reflux Still Condenser w/ Barb Connections 13 mm Inlet/Outlet Barbs (0.51 in.) Distillation Lid & Gasket Set of Adjustable Lid Clamps   Warning: Distilling alcohol without permits or licensing is illegal in many countries, including the United States.  It is the customer's responsibility to research their local, state, and federal laws and abide by those laws. Brewmaster is not responsible for any damage or injury caused by either misuse or unlawful use. Stills can also be used to produce essential oils, vinegar, purified water and engine fuel (requires permit in USA). 

Read more less

This propane burner is the same as our H210 burner, but for low pressure propane applications. Twenty individual jets combine to produce heat that will boil your water or wort in a hurry. Should be installed and connected by a professional plumber. Flame height is 2 to 3". Ring Diameter is 8" the inlet thread is 1/2" Female Pipe Thread. 20 Jets. This item is not intended for indoor use. These propane burners are not for use on portable propane tanks, they are for use with large propane tanks with regulators that typically feed rural homes where natural gas is not offered.  

Read more less

The Blichmann Engineering HellFire™ XL Burner fits kettles up to 25"! Including the 55 Gallon BoilerMaker™ Kettles. There's your everyday homebrew burner, and then there's the HellFire™ Burner! No doubt in a league of its own, the HellFire™ burner is the best burner on the market, and one that will not only make your brew day quicker, but will also last you for years of brewing to come. It's dual mode capability allows you to switch between High Efficiency mode (80,000 BTUs) and HellFire™ mode (140,000 BTUs). Efficient, fast, and versatile.  The new burner from Blichmann Engineering is appropriately named HellFire™!   This dual mode capability burner is unlike anything else on the market and is sure to satisfy all your heating needs.  No wonder it is patent pending!  This custom made burner is tuned to operate in high efficiency mode, and also in a secondary high power mode.  In the high power mode, you'll be amazed with 140,000 BTU/hr output for blazing fast heating - double the power of the previous design.  Waiting for a boil is now a thing of the past.  In the high efficiency mode, you'll get 80,000 BTU/hr and superb heat transfer to the wort and whisper quiet operation. Even our efficiency mode has significantly more power than the competition!  To top off all that power we include a patent pending heat shield to keep that massive power off your valve and thermometer and direct it to your wort. Features: Dual mode capacity High Power Mode: 140,000 BTU/hr Efficiency Mode: 80,000/hr Patent Pending Clip-on Heat Shield keeps valves cool Kettle Retaining bars adjust to accommodate kettles up to 20" in diameter Heavy Gauge Rust free Stainless Steel Construction will keep you brewing for years! Designed for outdoor use, the heat shield and body will protect your brew from wind  

Read more less

Convert the BrewBuilt T.C. brewing kettle into a mash tun using one of these false bottom kits. The heavy duty false bottom rests low in the kettle, utilizing a tri-clamp style maximizer that reduces dead space and pulls from the very bottom of your kettle, leaving no wort behind. A Silicone gasket rims the False Bottom, ensuring a tight seal to the wall with no chance of grain bypass. A handle is welded to the top of the false bottom for easy removal. To monitor your mash temperature, we recommend the 1.5" T.C. Thermometer with 6" probe for better grain bed penetration. 1.5" tri-clamp and gasket included Welded T.C. maximizer False bottom gasket for tight seal Welded legs and handle Made from 304 stainless steel NOTE: These false bottom kits will fit all BrewBuilt T.C. kettles, including the electric kettle with SlingBlade heating element. We do not recommend converting the electric kettle into a mash tun as the element will scorch the grain. If you wish to use the false bottom in your boil kettle, it should be noted that the screen is designed to filter grain, so fine particle vegetal matter will pass through.

Read more less

The DigiBoil is a versatile electric kettle that can be used as a standalone unit or integrated into your current brew system to serve a variety of functions. Easily brew 5-gallon extract batches. Use it to preheat your strike water or sparge water to a precise temperature. Pair it with a pump and heat exchanger to use it for HERMS brewing. Or slap on a still top lid and condenser for distilling! With so many ways to use the DigiBoil, and an affordable price tag to boot, it's hard not to get excited about this electric kettle! The Gen 2 DigiBoil features an upgraded glass lid, allowing you to monitor your heated or boiling liquid. Interested in using the DigiBoil for all-grain brewing? With the Mash Upgrade Kit, you can easily convert the DigiBoil into an electric mash tun! This DigiBoil model has two built-in heating elements that run off a 220V plug. One element is 1900w and the other is 500w for a combined 2400 watts! The elements can be individually controlled, allowing you to use a single element to gently hold temperatures, or engage both elements to quickly go from steeping temp to boiling. Temperatures are set and automatically maintained through the digital control panel. Simply set your desired temperature and flip on the heating element(s). If you have access to 220V power, this is definitely the unit we recommend. Although 110V power is enough to get up to boil, 220V will get you there faster and provide a much more vigorous boil. Integrated stainless ball valve comes with a 13mm barb (approx. 1/2"). The barb can be removed to attach 1/2" FPT fittings if desired. Features: 304 stainless steel construction 9 gallon total capacity Digital temperature control 220V / 15A power NEMA 6-30 plug (5 ft. cord) Dual heating element control (1900w and 500w) Heating elements are concealed for easy cleaning 304 stainless steel 1/2" ball valve with 13mm barb (approx. 1/2") Stamped-in volume markers (gallons & liters) Glass lid Temperature reads in °F or °C With elements turned off, hold both +/- buttons to switch between °F or °C Compatible with reflux and pot still (DS130 & DS120)* External Dimensions: 29" H x 15" W (including handles) Internal Dimensions: 19.5" H x 11.75" W ETL Listed *Distilling: to use the DigiBoil with a distilling condenser, you will need to purchase the Distillation Lid. Warning: Distilling alcohol without permits or licensing is illegal in many countries, including the United States.  It is the customer's responsibility to research their local, state, and federal laws and abide by those laws. Brewmaster is not responsible for any damage or injury caused by either misuse or unlawful use. Stills can also be used to produce essential oils, vinegar, purified water and engine fuel (requires permit in USA). KegLand Part Number: KL07252

Read more less

Welded 1.5" tri-clamp ports for a lifetime of leak-free use 304 stainless steel construction with mirror polish finish SlingBlade electric heating element with Tri-Clamp connections Front and back located handles with silicone grips Notched lid provides cover while not interfering with immersion chillers, hop bags, or other accessories The BrewBuilt Electric Kettle The BrewBuilt Electric Brewing Kettle features an offset welded tri-clamp ferrule for easy installation of the SlingBlade electric heating element. The SlingBlade elements were designed specifically for the BrewBuilt kettles and each element fits the corresponding kettle like a glove, perfectly matching the curvature of the kettle wall and providing the appropriate amount of power for the volume size. The unique crescent-shaped design places the element on one side of the kettle, leaving the opposite side clear for an immersion chiller or other accessories. Positioning the element in this way also promotes a rolling boil that evenly ditributes heat throughout the kettle. You'll love the results you get with the SlingBlade's ultra-low watt density, which won't scorch your wort. The kettle does not come with a power cord so you'll need to provide your own extension cord, or add our watertight On/Off power switch for the most convenient way to power the element. Handles are located at the front and back, rather than either side, saving you space when building out a horizontal system and will keep fittings pointed away from you regardless of which side you pick up the kettle from. This model includes a T.C. x FPT ball valve with oversized 5/8" barb—ideal for using 1/2" ID silicone transfer tubing. Also available with Butterfly Valve or T.C. x T.C. Ball Valve hardware packs. Designed for Brewing. Built to Last. BrewBuilt brew kettles are made from 304 stainless steel and offer an unparalleled mix of features for the price. At the very top of the list are two welded-in place tri-clamp couplers that offer a lifetime of leak free use.  As you can imagine, welding in a coupler costs more than punching a hole and using a gasketed (i.e. weld-less) fitting. Welded fittings offer a permanent connection that to us is worth every penny.  The second unique feature that we absolutely love about these brew kettles is the notched lid with silicone plug.  This notch allows you so much flexibility; you can use an immersion chiller, one of our Ultimate Sparge Arms for mashing, tie off hop bags, take a temp reading during cooling, or whatever else we all can dream up. Our T.C. kettles were designed to keep pace with the ever-evolving world of brewing technology. Tri-clamp fittings are standard fare in professional breweries, and they’ve been widely adopted in homebrewing as T.C. fermenters and pumps become more affordable and widely available. Tri-clamp fittings, also known as Tri-clover, allow you to make a sanitary connection that is free of nooks and crannies for contaminants to take hold. They are much easier to break down for cleaning compared to threaded connections, and they don’t require Teflon tape to make a watertight seal. T.C. fittings and accessories also give you the distinct advantage of being able to clean in place (CIP), so you don’t need to break down your entire system after every brew day. This Brew Kettle has a lot to offer... Some other features we dig include the internal volume markers from the bottom to the top - so handy for instant reads.  The silicone sleeved handles on the kettle and the lid are a cool feature to protect your hands. The tri-clad bottom with a 4mm core of aluminum sandwiched between two layers of stainless steel offers even heat distribution during the boil and also makes it a perfect choice for anyone wanting to use an induction burner.  The bottom coupler is also cool with 1/2" male threads on the outside and 1/2'' female threads on the inside.   Beefy 304 Stainless These kettles are made from 304 grade stainless.  That means you will have less corrosion issues than with a kettle made from lower grade 201 type stainless. We put these kettles through a corrosive salt water test in the MoreBeer! shop and they passed with flying colors. We also made sure the rivets and riveted handles were also made of stainless steel for a long term, trouble free life.  The 10 and 15 gallon size are made from 1.0mm thick stainless steel. The 20, 30 and 50 gallon size are made with 1.2mm stainless - that's pretty thick stuff - and you will know it when you pick one up. The included ball valve is a two piece design that allows for easy cleaning (we prefer these over 3 piece for ease of assembly) and is also made from 304 stainless.  Mirror Polish Finish The mirror polish finish isn’t just for making your Instagram feed pop! This extra slick finish is much easier to clean and sanitize than a standard brushed stainless kettle. Hop trub and other organic solids left behind after a brew day will have a hard time clinging to the interior surface and scrub away with ease. Size Ratios and Stuff All the BrewBuilt kettles follow the recent trend to a 1.2:1 ratio where the height is 1.2 times the diameter. This is a proven commercial ratio that has been adopted in homebrewing to achieve a more consistent 10% evaporation rate during the boil.  We do like this ratio for boiling. For Mashing we would prefer a little bit shallower but that is a small compromise. Dimensions for a hot-liquor tank, if you are thinking brewing system down the road, are irrelevant as any ratio kettle will do.   Final Words With welded tri-clamp fittings, mirror polish finish, a bunch of cool features, and a solid, thick 304 stainless steel core this kettle is a pretty amazing value. Remember, if you order from MoreBeer! we ship free anywhere in the continental USA! SlingBlade Heating Elements The BrewBuilt SlingBlade's unique crescent-shaped design promotes a rolling boil and even heat distribution. This electric heating element places all of the heating power on one side of the kettle, sending thermal energy upward to the surface that then cascades downward on the opposite side of the kettle. This movement creates a natural turbulence that evenly distributes heat while creating a vigorous boil. By being located on one side of the kettle, the other side is clear for immersion chillers, and the curved shape won't obstruct the flow of wort during whirlpool. Thanks to the non-circular design, the SlingBlade can easily be installed on any kettle with a 1.5" tri-clamp ferrule. This also makes removing the element for cleaning between uses a breeze. Kettle Key Features: Three welded T.C. couplers for a lifetime of leak free use 50-gal kettle has four welded T.C. couplers to use with two heating elements T.C. x FPT ball valve with 5/8" barb AISI304 Stainless Steel construction for longevity and excellent corrosion resistance Stainless handles and rivets for secure lifting Silicone coated kettle and lid handles for heat protection Lid is designed to conveniently hang from a handle 4 mm Tri-Clad Bottom with Aluminum Core heats quickly and disperses heat evenly to prevent scorching Induction burner compatible 1.0mm (10 & 15 gal) or 1.2mm (20, 30 & 50 gal) thick side walls resist denting 1.2:1 height to diameter ratio provides optimal evaporation rate during boiling Industry-First notched lid with silicone plug accommodates an immersion chiller or sparge arm Internally etched volume markers from top to bottom for easy filling SlingBlade Key Features: Made from Stainless Steel with proprietary coating for long life 1.5" Tri-Clamp connection Unique offset design promotes rolling boil Ultra-Low Watt Density eliminates scorching UL Certified components 240 Volt L6-30 plug 20 Amp breaker required for 10 & 15-gallon kettle 30 Amp breaker required for 20 & 30-gallon kettle 50-gallon kettle uses 2 x heating elements and requires 2 x 30 amp circuits SKU Size Element Wattage Kettle ID (in.) Height (in.) BE581A 10 3750 13.78 16.54 BE582A 15 4500 15.75 18.90 BE583A 20 5000 17.72 21.26 BE584A 30 5750 19.69 23.62 BE585A 50 (2) 5750 23.6 28.30   ***In order to avoid injury or death we strongly recommend using a GFCI in any circuit used near water. You can find one here.***   Lowest Price Guarantee, this item has MAP pricing so you can be confident you won't find it for less.

Read more less

Preheat your mash before beginning the brewing process with this 1000W Electric Bucket Heater. This handy little tool works in conjunction with a product like the Ranco or Johnson temperature controller by enabling you to set an exact hot liquid temperature on the controller, and then attaching it to the bucket heater. The temperature controller will turn off the bucket heater once it reaches your desired temperature. Our bucket water heater is designed to use with water in a bucket or cooler where an open flame cannot be used, and you can even use it to heat a bucket of water for cleaning with a powdered brewery wash. This water bucket heater measures 17 inches from the handle to the tip and comes with a 6-foot long cord. It requires at least 6 inches of water for full submersion, and it can only be used with a maximum depth of 14 inches.  Unit has stainless steal heating element and guard.  Does not include clip for mounting.  Please Note - Having electrical devices around liquid can be hazardous, and should not be left unattended. Please use caution while using this device, and read the instruction manual prior to use.

Read more less

Kettle Maximizer allows you to pull liquor or wort from below the depth of your kettle's bottom port Angle straight down in hot liquor tanks to maximize pick up Rotate to your preferred pick-up height in boil kettles to leave trub behind when transferring to fermenter The tri-clamp maximizer is recommended for boil kettles and hot liquor tanks with 1.5" T.C. bottom ports. This fitting will allow you to pull liquor or wort from below the depth of your kettle's bottom port without the need to tip your vessel. For hot liquor tanks, point the end of the tube straight down to maximize pick up. For boil kettles, you can rotate the maximizer to position the end of the tube at your preferred height above the bottom of the kettle, leaving room for a layer of trub that will be left behind in the kettle when you transfer wort to your fermenter. 1.5" tri-clamp Tube Length: 6.5" Overall Length: 8.18" Made from stainless steel

Read more less

Using an electric Recirculation Infusion Mash System heater to heat your mash is one of the safest and most energy-efficient ways to get your brew to the perfect temperature, and the Blichmann RIMS-Rocket is one of the most popular models on the market today. This innovative heater is designed especially for use with the popular Blichmann HopRocket™ canister, and to install it all you have to do is secure it inside of the canister, plug it in, and monitor the temperature.   The RIMS-Rocket operates with 3500 W, 240V and ultra low watt density in order to perform optimally in your RIMS system. It features a "plug and play" 12-foot long factory wired cable with a molded twist-lock L6-30P plug on one end and a removable plug on the other end, making it easy to clean because there are no dangling cords attached to the side of your heater. Best of all, the ultra low watt density ensures that you’ll never scorch your mash during the heating process!    Features: The RIMS-Rockettm heating element is 3500 W, 240V, ultra low watt density and is engineered to perform optimally in your RIMS system Removable custom engineered plug means cleaning is a snap - no dangling power cord tethered to your heater and the terminal pins are spray-down capable!  The RIMS-Rockettm includes a "plug and play" 12ft factory wired cable with a molded twist-lock L6-30P plug on one end, and our custom removable plug on the other end. Less than Ultra low watt density means NO chance of scorching, and dry-fire capable (although we certainly don't recommend this!) Please note: mounting bracket sold separately.

Read more less

This amazing product is an ideal companion with Blichmann’s revolutionary BoilCoil™ immersion heaters, but it’ll also work with all manufacturer’s immersion heaters!  Blichmann’s unique modular power controller lets you precisely control the power of your electric heating element from 0-100% power.  Need to control more than one heating element for large kettles?  Simply add up to 4 additional relay modules and drive them all with one power controller.  Unlike cheap "dimmer switch" based power controllers, whose power output is not linear, the modular power controller is much easier to control the perfect boil intensity and heating rate.  This is accomplished using a tried and true industrial technique called Pulse Width Modulation (PWM).  Simply put, it controls the percentage of time the heater is energized over a very short 1 sec interval.  So turning the knob to “6” energizes the heater for 0.6 seconds, and turns it off for the remainder of the 1 sec interval.  This robust reliable technique is gentle on your heater, is extremely linear, and doesn’t create electrical noise like other techniques can.  See below for other great features. Precise linear control of power from 0-100% with a fast-acting intuitive power knob Industrial grade PWM control methodology is reliable, gentle to heating elements, and very linear Ideal for boil kettle and BIAB applications where temperature control is not needed, but precise power control is.  Note that this product does not read or control temperature Allows you to dial in an exact and repeatable boil off rate to hit your final boil volume batch after batch Perfect match for Blichmann’s BoilCoil™ electric heaters, but also works with any manufacturer’s immersion heater 30A 240V (7200W) single phase, and 20A 120V (2400W) models available L6-30 30A 240V or L6-20 120V with power cable “pigtails” available Have a large kettle with more than on heating element?  Up to 4 optional relay modules can be quickly installed allowing you to drive up to 5 heating elements simultaneously with one power controller Unique enclosure has provisions to route cables out of the back for table mounting, or out of the bottom for wall mounting.  Field changeable Integral DIN rail groove on the back allows connecting multiple controllers and relay modules together for wall or table mounting using readily available DIN mounting channels   Note: Power relay sold separately (BL996). Mounting bracket sold separately (BL997).

Read more less

Use this lid along with the 65L BrewZilla or DigiBoil and a copper still top (DS120 or DS130) to make your own easy-to-use distillery. The lid gasket has two distinct sides, one that is rounded and one that is completely flat. When installing the gasket the flat side should be facing up. Use one hand to stretch the gasket around the lid and the other to push the gasket into the channel. This lid has a 1.85" (47mm) hole for the still top. Lid gasket included. Note: This lid uses a 6mm gasket to better fit the Gen 4 BrewZilla and Gen 2 DigiBoil. It is also backwards compatible with Gen 3 and older BrewZillas and Gen 1 DigiBoils. To improve the seal further, we highly recommend using the Adjustable Lid Clamps with the Distillation Lid if your unit does not have them. Made from 304 stainless steel Measures 16.25" in diameter KegLand Part Number: KL10962

Read more less

11.5 ft. extension cord for Blichmann 240V Power Controller (BL995).

Read more less

Recirculate wort in your boil kettle without sacrificing one of your tri-clamp ports. The BrewBuilt Whirlpool Return Fitting & Thermowell Offset kit allows you to use any tri-clamp kettle's thermometer port to recirculate wort while also taking temp readings. This kit is perfect for kettles that only have two tri-clamp ports—eliminating the need to drill out a hole in your kettle to add a third port for wort recirculation. Attach your preferred valve or tri-clamp fitting to the side inlet and, during whirlpool, draw wort from your bottom port and pump it back through the Whirlpool Return Fitting. Kit Includes: Whirlpool Return Fitting Thermowell Offset (1) 1.5" Tri-Clamp (1) 1.5" Tri-Clamp Gasket (EPDM)

Read more less

Designed to handle up to 15 amp power draw.  This small compact controller is fairly easy to fit into the DigiBoil units. Simply remove the base of the DigiBoil with a Phililips head screwdriver, undo the plastic box then swap out the main board controller. Suitable for 110V 35L DigiBoil.

Read more less

For the peace-of-mind of knowing it will light every time! Easy to install, easy to use.   Using a Camp Chef to boil your homebrew? Lighting it with matches or a lighter can be a source of frustration on brew day. If you're tired of lighting your camp chef manually, this easy-to-install Camp Chef Ignitor will ease your burden. The Camp Chef Ignitor mounts right on to the Camp Chef burner via an existing mounting hole installed specifically for this purpose.    The Camp Chef Igniter operates with a push-button “sparker,” which is similar to the ones found on furnaces, hot water heaters, and BBQs. 

Read more less

Digital temperature control Triple heating element control (2000w, 1000w and 500w) 17 gallon total capacity 304 stainless steel construction 220V / 20A power This is a versatile electric kettle that can be used as a standalone unit or integrated into your current brew system to serve a variety of functions. Easily brew 10-gallon extract batches. Use it to preheat your strike water or sparge water to a precise temperature. Pair it with a pump and heat exchanger to use it for HERMS brewing. Or slap on a still top lid and condenser for distilling! With so many ways to use the DigiBoil, and an affordable price tag to boot, it's hard not to get excited about this electric kettle! The Gen 2 DigiBoil features an upgraded glass lid, allowing you to monitor your heated or boiling liquid. Interested in using the DigiBoil for all-grain brewing? With the Mash Upgrade Kit, you can easily convert the DigiBoil into an electric mash tun! This DigiBoil model has three built-in heating elements that run off a 220V plug. The elements are 2000w, 1000w and 500w for a combined 3500 watts! The elements can be individually controlled, allowing you to use a single element to gently hold temperatures, or engage all three elements to quickly go from steeping temp to boiling. Temperatures are set and automatically maintained through the digital control panel. Simply set your desired temperature and flip on the heating element(s).  Integrated stainless ball valve comes with a 13mm barb (approx. 1/2"). The barb can be removed to attach 1/2" FPT fittings if desired. More! Features: NEMA 6-30R plug (4.5 ft. cord) Heating elements are concealed for easy cleaning 304 stainless steel 1/2" ball valve with 13mm barb (approx. 1/2") Stamped-in volume markers (gallons & liters) Glass lid Temperature reads in °F or °C With elements turned off, hold both the +/- buttons to switch between °F or °C Compatible with reflux and pot still (DS130 & DS120)* External Dimensions: 29" H x 19.5" W (including handles) Internal Dimensions: 20.25" H x 15.75" W ETL Listed *Distilling: to use the DigiBoil with a distilling condenser, you will need to purchase the still top lid (DS127). Warning: Distilling alcohol without permits or licensing is illegal in many countries, including the United States.  It is the customer's responsibility to research their local, state, and federal laws and abide by those laws. MoreBeer! is not responsible for any damage or injury caused by either misuse or unlawful use. Stills can also be used to produce essential oils, vinegar, purified water and engine fuel (requires permit in USA).   Kegland Part number: KL07313 NOTE: Due to the size of this item, it is not eligible for international shipping.    

Read more less

Keep trub out of your fermenter by adding hops to your boil kettle using this Hop Spider Adjustable mounting arms make the Hop Spider compatible with most kettles up to 20 gallon in size Basket is removable for easy cleaning Made from 304 stainless steel and high temp silicone Keeping trub and hop material in your kettle and out of your fermenter is one of the critical components to ensuring clear beer in your pint glass! On top of that, brewing with whole cone hops can introduce a lot of hop leaf material that easily overwhelms and clogs transfer lines creating lots of headaches. Ss Hop Spider helps with these challenges by containing hop material within a fine mesh, photo-chemical etched basket. The basket sits inside a custom-designed ring mount with Silicone Adjustment Arms so you can dial in the Hop Spider for the perfect fit on your kettle.  Intended for use with SVBS, Ss Brewtech TC Brew Kettles (10 gal, 15 gal & 20 gal), and Ss Brewtech eKettles. Not compatible with Ss Brewtech 30 gal & 50 gal Brew Kettles and Ss Brewtech 5.5 gal Mini Brew Kettle.  Features: 400 Micron Photo-Chemical Etching Adjustable Mounting Arm Removable Basket for Easy Cleaning Specifications: 304 Stainless Steel and High Temp Silicone 6” Basket Diameter 15.5” Basket Height 15" Adjustment Arm Minimum Length 18" Adjustment Arm Maximum Length Package Dimensions: 11"H x 9.5"W x 19"L 6lbs

Read more less

Compact and powerful, this little cooker is a homebrewer's dream! The 60,000 btu maximum output high-pressure burner heats mass amounts of liquid in a hurry and will maintain it at boiling temperatures making it a great cooker for home water bath canning, sea food boils, and of course—home brewing beer! If you've been brewing on the stove top and looking to take your brew days outside, the Camp Chef Burner is great intro burner for full volume boils. And thanks to its compact size, it won't take up a ton of room when stored between batches! Features: Includes 3 ft. hose and regulator Includes detachable steel legs for stability and portability High output High pressure Boils and heats water very quickly Durable, rugged design built to last Specs: Dimensions (base): 20 in. x 20 in. Cooking Area: 15 in. diameter Cooker Height: 16 in. Cooker Weight: 11.5 lbs. Output: 60,000 BTUs/Hr. Burner Warranty: One Year  

Read more less

Using an electric Recirculation Infusion Mash System heater to heat your mash is one of the safest and most energy-efficient ways to get your brew to the perfect temperature, and the Blichmann RIMS-Rocket is one of the most popular models on the market today. This innovative heater is designed especially for use with the popular Blichmann HopRocket™ canister, and to install it all you have to do is secure it inside of the canister, plug it in, and monitor the temperature. The RIMS-Rocket operates with 2000 W, 120V and ultra low watt density in order to perform optimally in your RIMS system. It features a "plug and play" 12-foot long factory wired cable with a molded twist-lock L6-30P plug on one end and a removable plug on the other end, making it easy to clean because there are no dangling cords attached to the side of your heater. Best of all, the ultra low watt density ensures that you’ll never scorch your mash during the heating process!  Features: The RIMS-Rockettm heating element is 2000 W, 120V, ultra low watt density and is engineered to perform optimally in your RIMS system Removable custom engineered plug means cleaning is a snap - no dangling power cord tethered to your heater and the terminal pins are spray-down capable!  The RIMS-Rockettm heater assembly clamps right into our HopRockettm canister for added versatility and lower cost. The RIMS-Rockettm includes a "plug and play" 12ft factory wired cable with a molded twist-lock L6-30P plug on one end, and our custom removable plug on the other end. Less than Ultra low watt density means NO chance of scorching, and dry-fire capable (although we certainly don't recommend this!) Please note: mounting bracket sold separately.  

Read more less

If you want to add a false bottom to your beloved 20 Gallon Blichmann BoilerMaker™ Brew Kettle in order to use it as a mash tun, this Blichmann 20 Gallon BoilerMaker False Bottom is designed especially to fit seamlessly for that exact purpose. This high quality false bottom is designed specifically for Blichmann kettles, and is necessary to convert one to a mash tun. The Blichmann 20 Gallon BoilerMaker False Bottom is made with a patent pending button louver design that is a hybrid of a perforated false bottom and a slotted manifold, combining the most beneficial qualities of both styles to truly give you the best of both worlds. MoreBeer! also sells the BoilerMaker False Bottom in the following sizes: ·         Blichmann False Bottom for 7.5 Gallon BoilerMaker Brew Pot ·         Blichmann False Bottom for 10 Gallon BoilerMaker Brew Pot ·         Blichmann False Bottom for 15 Gallon BoilerMaker Brew Pot ·         Blichmann False Bottom for 15 Gallon BoilerMaker G2 Brew Pot ·         Blichmann False Bottom for 30 Gallon BoilerMaker Brew Pot ·         Blichmann False Bottom for 55 Gallon BoilerMaker Brew Pot Please Note: This False Bottom is for the BoilerMaker™ G1 & G2 20 gal Brew Pots by Blichmann Engineering™

Read more less

This new Blichmann Engineering innovation redefines electric heating!  Unrivaled performance, speed, and simplicity.  Just plug in a BoilCoil™ immersion heater for immediate, high efficiency heat.  Ideal for indoor brewing and a perfect companion for your BoilerMaker­™ brew pot.  It is easily installed in your previously purchased BoilerMaker™ pot, or most other manufacturers pots by drilling two small 5/8" holes with our handy drill template.  We include a "plug and play" 12 ft factory wired cable with a molded twist-lock plug on one end, and our custom removable plug on the other end.  Hot, fast, and easy.  Just the way you like it. Features: Each BoilCoil™ is engineered to perform optimally in your BoilerMaker™ brew pot for consistent heating performance, boil quality, and boil-off rates.   Removable custom engineered plug means cleaning is a snap - no dangling power cord tethered to your pot!   Coil configuration hugs the wall of the pot to encourage convective boil characteristics to drive off DMS and other volatiles and doesn't interfere with whirlpooling   The BoilCoil™ includes a "plug and play" 12 ft factory wired cable with a molded twist-lock L6-30P plug on one end, and our custom removable plug on the other end.   LESS THAN Ultra low watt density means NO chance of scorching, and dry-fire capable (although we certainly don't recommend this!).   Simple installation requires drilling only two small 5/8" holes with our handy drill template.   No risky welding or cutting massive holes in your pot to install, and features a professional and reliable connection and sealing system engineered specifically for homebrew kettles.   The BoilCoil™ will fit in most competitive pots too!  See data tab for dimensional drawing.   Couple with the electric BrewCommander™ controller for the ultimate in temperature control.   Kettle Size: For 55 gal Boilermakers™ Rated Voltage (VAC): 240 v Recommended GFCI Breaker Size: 50 amp Power (W): 5750 X 2 W Please Note: The 55 gallon BoilerMaker™ requires two BoilCoil™ elements if it will be used as a boil kettle. If it will be used as a hot liquor tank, one coil is sufficient. 

Read more less

This new Blichmann Engineering innovation redefines electric heating!  Unrivaled performance, speed, and simplicity.  Just plug in a BoilCoil™ immersion heater for immediate, high efficiency heat.  Ideal for indoor brewing and a perfect companion for your BoilerMaker­™ brew pot.  It is easily installed in your previously purchased BoilerMaker™ pot, or most other manufacturers pots by drilling two small 5/8" holes with our handy drill template.  We include a "plug and play" 12 ft factory wired cable with a molded twist-lock plug on one end, and our custom removable plug on the other end.  Hot, fast, and easy.  Just the way you like it. Features: Each BoilCoil™ is engineered to perform optimally in your BoilerMaker™ brew pot for consistent heating performance, boil quality, and boil-off rates.   Removable custom engineered plug means cleaning is a snap - no dangling power cord tethered to your pot!   Coil configuration hugs the wall of the pot to encourage convective boil characteristics to drive off DMS and other volatiles and doesn't interfere with whirlpooling   The BoilCoil™ includes a "plug and play" 12 ft factory wired cable with a molded twist-lock L6-30P plug on one end, and our custom removable plug on the other end.   LESS THAN Ultra low watt density means NO chance of scorching, and dry-fire capable (although we certainly don't recommend this!).   Simple installation requires drilling only two small 5/8" holes with our handy drill template.   No risky welding or cutting massive holes in your pot to install, and features a professional and reliable connection and sealing system engineered specifically for homebrew kettles.   The BoilCoil™ will fit in most competitive pots too!  See data tab for dimensional drawing.   Couple with the electric BrewCommander™ controller for the ultimate in temperature control.   Kettle Size: For 15 gal Boilermakers™ Rated Voltage (VAC): 240 v Recommended GFCI Breaker Size: 20/30 amp Power (W): 4500 W

Read more less

The 10 gallon BoilerMaker™ G2 is a no compromise premium brew pot packed with standard features like a patent pending linear flow drain valve that can be oriented in any direction and disassembles in seconds for cleaning.  This US made single piece construction pot carries a lifetime limited warranty.  From the sleek easy to clean surface finish, to the cool touch custom molded grips, durable easy to read level gauge, snap-in drain tube, the informative BrewMometer™ and broad suite of accessories like our patented Button Louver™false bottom, patented HopBlocker™ and AutoSparge™, this pot defines awesomeness.  The BoilerMaker™ G2 is clearly in a class of its own. All the items you need come standard, installed, and ready to use on the G2 10 gallon brew pot: Heavy gauge, 304 single piece, deep drawn, weld-free American made construction will turn this 10 gallon pot into a family heirloom* Blichmann Engineering was the innovator of the 1.2 height to diameter ratio not the imitator!  All of our pots perform consistently and flawlessly with homebrewers in mind Patent pending parabolic valve provides linear flow for unparalleled flow control. Built in 90 degree outlet can be oriented at any angle to make hose routing simple and kink free.Cool touch silicone grip makes handling under fire easy. Fixed angle BrewMometer™ with their unique patented brewing dialface - the ultimate in brewing convenience Improved surface finish hides finger-prints and cleans impeccably.  Sleek brush on the outside and a silky smooth satin finish on the inside. Standard heavy-duty borosilicate glass level gauge never clouds or scratch. Features rugged stainless steel guard with engraved volume graduations, cleaning brush and clean-out ports.  Much easier and more accurate than internal graduations.  It will also act as a mash manometer and warn you of impending stuck mashes! Exclusive snap-in dip tube design installs without tools and drains to within 3/8” of bottom! Handle orientation that makes carrying easier and lid storage on the pot handle. Cool touch high impact glass filled nylon handles are durable, comfortable, and cool to the touch. Stepped bottom on pot supports mash screen and virtually eliminates sidewall shunting. A great way to start with high-quality equipment equipped with all the options.

Read more less

Welded 1.5" tri-clamp ports for a lifetime of leak-free use Front & back positioned handles reduce the space needed to arrange multiple kettles in a horizontal system 304 stainless steel construction with mirror polish finish Notched lid provides cover while not interfering with immersion chillers, hop bags, or other accessories Choose from Boil Kettle, Hot Liquor Tank or Mash Tun configurations The Boil Kettle comes without fittings The Hot Liquor Tank includes a Kettle Maximizer and Thermometer with 2" Probe The Mash Tun includes a False Bottom Kit and Thermometer with 6" Probe Add your preferred Valve Hardware Pack when choosing your kettle above or purchase your own valve & fittings separately Designed for Brewing. Built to Last. BrewBuilt brew kettles are made from 304 stainless steel and offer an unparalleled mix of features for the price. At the very top of the list are two welded-in place tri-clamp couplers that offer a lifetime of leak free use.  As you can imagine, welding in a coupler costs more than punching a hole and using a gasketed (i.e. weld-less) fitting. Welded fittings offer a permanent connection that to us is worth every penny.  The second unique feature that we absolutely love about these brew kettles is the notched lid with silicone plug.  This notch allows you so much flexibility; you can use an immersion chiller, one of our Ultimate Sparge Arms for mashing, tie off hop bags, take a temp reading during cooling, or whatever else we all can dream up. Our new T.C. kettles were designed to keep pace with the ever-evolving world of brewing technology. Tri-clamp fittings are standard fare in professional breweries, and they’ve been widely adopted in homebrewing as T.C. fermenters and pumps become more affordable and widely available. Tri-clamp fittings, also known as Tri-clover, allow you to make a sanitary connection that is free of nooks and crannies for contaminants to take hold. They are much easier to break down for cleaning compared to threaded connections, and they don’t require Teflon tape to make a watertight seal. T.C. fittings and accessories also give you the distinct advantage of being able to clean in place (CIP), so you don’t need to break down your entire system after every brew day. Configurations The base boil kettle comes without fittings so you can modify it the specific tri-clamp accessories that best suit your needs. Add one of the optional Brewing Kettle Valve Packs above which include your choice of valve and all the hardware you'll need to connect 1/2" ID transfer tubing, as well as an end cap to seal the top port if a thermometer or other accessory is not in place. The Hot Liquor Tank includes the base kettle plus a kettle maximizer for the bottom port and thermometer with 2" probe for the top port. Clamps and gaskets are included to attach the tri-clamp kettle maximizer and the thermometer. The Mash Tun includes the base kettle plus a false bottom kit for the bottom port and thermometer with 6" probe for the top port. Clamps and gaskets are included to attach the tri-clamp false bottom maximizer and the thermometer. Kettles do not come with a valve or additional fittings for the bottom port as standard. Add one of our pre-configured Valve Packs or purchase your preferred valve and fittings separately. This Brew Kettle has a lot to offer... Some other features we dig include the internal volume markers from the bottom to the top - so handy for instant reads.  The silicone sleeved handles on the kettle and the lid are a cool feature to protect your hands. The tri-clad bottom with a 4mm core of aluminum sandwiched between two layers of stainless steel offers even heat distribution during the boil and also makes it a perfect choice for anyone wanting to use an induction burner.   Beefy 304 Stainless These kettles are made from 304 grade stainless.  That means you will have less corrosion issues than with a kettle made from lower grade 201 type stainless. We put these kettles through a corrosive salt water test in the MoreBeer! shop and they passed with flying colors. We also made sure the rivets and riveted handles were also made of stainless steel for a long term, trouble free life.  The 10 and 15 gallon size are made from 1.0mm thick stainless steel. The 20, 30 and 50 gallon size are made with 1.2mm stainless - that's pretty thick stuff - and you will know it when you pick one up.  Mirror Polish Finish The mirror polish finish isn’t just for making your Instagram feed pop! This extra slick finish is much easier to clean and sanitize than a standard brushed stainless kettle. Hop trub and other organic solids left behind after a brew day will have a hard time clinging to the interior surface and scrub away with ease. Size Ratios and Stuff All the BrewBuilt kettles follow the recent trend to a 1.2:1 ratio where the height is 1.2 times the diameter. This is a proven commercial ratio that has been adopted in homebrewing to achieve a more consistent 10% evaporation rate during the boil.  We do like this ratio for boiling. For Mashing we would prefer a little bit shallower but that is a small compromise. Dimensions for a hot-liquor tank, if you are thinking brewing system down the road, are irrelevant as any ratio kettle will do. Features: Two welded T.C. couplers for a lifetime of leak free use Front & back oriented handles with silicone coated handles for heat protection Notched lid with silicone plug for flexibility 304 stainless steel construction for longevity 1.0mm (10 & 15 gal) or 1.2mm (20, 30 & 50 gal) thick side walls resist denting 4mm Tri-Clad Aluminum bottom sandwiched between two layers of stainless steel for no scorching Internally etched volume markers from top to bottom for easy reading 1.2:1 Ratio is optimal for boiling evaporation rate Lid is designed to conveniently hang from a handle  Stainless handles with stainless rivets for secure lifting   Size Kettle ID (in.) Height (in.) 10 Gallon 13.78 16.54 15 Gallon 15.75 18.90 20 Gallon 17.72 21.26 30 Gallon 19.69 23.62 50 Gallon 23.62 28.30    

Read more less

Have a weak burner that needs an upgrade? Putting together your own 3 Vessel brewing system? Then this burly Multi-Jet burner is just the ticket.   Twenty individual jets combine to produce heat that will boil your water or wort in a hurry. Should be installed and connected by a professional plumber.    Specifications: Cast Iron body with Brass burner jets 2-3" Flame Height  8" Ring Diameter  1/2" Female Pipe Thread Inlet 20 Jets This item is not intended for indoor use.

Read more less

The 20 gallon BoilerMaker™ G2 is a no compromise premium brew pot packed with standard features like a patent pending linear flow drain valve that can be oriented in any direction and disassembles in seconds for cleaning.  This US made single piece construction pot carries a lifetime limited warranty.  From the sleek easy to clean surface finish, to the cool touch custom molded grips, durable easy to read level gauge, snap-in drain tube, the informative BrewMometer™ and broad suite of accessories like our patented Button Louver™false bottom, patented HopBlocker™ and AutoSparge™, this pot defines awesomeness.  The BoilerMaker™ G2 is clearly in a class of its own. All the items you need come standard, installed, and ready to use on the G2 Brew Pot: Heavy gauge, 304 single piece, deep drawn, weld-free American made construction will turn this pot into a family heirloom* Blichmann Engineering was the innovator of the 1.2 height to diameter ratio not the imitator!  All of our pots perform consistently and flawlessly with homebrewers in mind Patent pending parabolic valve provides linear flow for unparalleled flow control. Built in 90 degree outlet can be oriented at any angle to make hose routing simple and kink free.Cool touch silicone grip makes handling under fire easy. Fixed angle BrewMometer™ with their unique patented brewing dialface - the ultimate in brewing convenience Improved surface finish hides finger-prints and cleans impeccably.  Sleek brush on the outside and a silky smooth satin finish on the inside. Standard heavy-duty borosilicate glass level gauge never clouds or scratch. Features rugged stainless steel guard with engraved volume graduations, cleaning brush and clean-out ports.  Much easier and more accurate than internal graduations.  It will also act as a mash manometer and warn you of impending stuck mashes! Exclusive snap-in dip tube design installs without tools and drains to within 3/8” of bottom! Handle orientation that makes carrying easier and lid storage on the pot handle. Cool touch high impact glass filled nylon handles are durable, comfortable, and cool to the touch. Stepped bottom on pot supports mash screen and virtually eliminates sidewall shunting. A great way to start with high-quality equipment equipped with all the options.

Read more less

Welded 1.5" tri-clamp ports for a lifetime of leak-free use 304 stainless steel construction with mirror polish finish SlingBlade electric heating element with Tri-Clamp connections Front and back located handles with silicone grips Notched lid provides cover while not interfering with immersion chillers, hop bags, or other accessories The BrewBuilt Electric Kettle The BrewBuilt Electric Brewing Kettle features an offset welded tri-clamp ferrule for easy installation of the SlingBlade electric heating element. The SlingBlade elements were designed specifically for the BrewBuilt kettles and each element fits the corresponding kettle like a glove, perfectly matching the curvature of the kettle wall and providing the appropriate amount of power for the volume size. The unique crescent-shaped design places the element on one side of the kettle, leaving the opposite side clear for an immersion chiller or other accessories. Positioning the element in this way also promotes a rolling boil that evenly ditributes heat throughout the kettle. You'll love the results you get with the SlingBlade's ultra-low watt density, which won't scorch your wort. The kettle does not come with a power cord so you'll need to provide your own extension cord, or add our watertight On/Off power switch for the most convenient way to power the element. Handles are located at the front and back, rather than either side, saving you space when building out a horizontal system and will keep fittings pointed away from you regardless of which side you pick up the kettle from. This model includes a Butterfly Valve with 1/2" barb. Also available with T.C. x FPT or T.C. x T.C. Ball Valve hardware packs. Designed for Brewing. Built to Last. BrewBuilt brew kettles are made from 304 stainless steel and offer an unparalleled mix of features for the price. At the very top of the list are two welded-in place tri-clamp couplers that offer a lifetime of leak free use.  As you can imagine, welding in a coupler costs more than punching a hole and using a gasketed (i.e. weld-less) fitting. Welded fittings offer a permanent connection that to us is worth every penny.  The second unique feature that we absolutely love about these brew kettles is the notched lid with silicone plug.  This notch allows you so much flexibility; you can use an immersion chiller, one of our Ultimate Sparge Arms for mashing, tie off hop bags, take a temp reading during cooling, or whatever else we all can dream up. Our T.C. kettles were designed to keep pace with the ever-evolving world of brewing technology. Tri-clamp fittings are standard fare in professional breweries, and they’ve been widely adopted in homebrewing as T.C. fermenters and pumps become more affordable and widely available. Tri-clamp fittings, also known as Tri-clover, allow you to make a sanitary connection that is free of nooks and crannies for contaminants to take hold. They are much easier to break down for cleaning compared to threaded connections, and they don’t require Teflon tape to make a watertight seal. T.C. fittings and accessories also give you the distinct advantage of being able to clean in place (CIP), so you don’t need to break down your entire system after every brew day. This Brew Kettle has a lot to offer... Some other features we dig include the internal volume markers from the bottom to the top - so handy for instant reads.  The silicone sleeved handles on the kettle and the lid are a cool feature to protect your hands. The tri-clad bottom with a 4mm core of aluminum sandwiched between two layers of stainless steel offers even heat distribution during the boil and also makes it a perfect choice for anyone wanting to use an induction burner.  The bottom coupler is also cool with 1/2" male threads on the outside and 1/2'' female threads on the inside.   Beefy 304 Stainless These kettles are made from 304 grade stainless.  That means you will have less corrosion issues than with a kettle made from lower grade 201 type stainless. We put these kettles through a corrosive salt water test in the MoreBeer! shop and they passed with flying colors. We also made sure the rivets and riveted handles were also made of stainless steel for a long term, trouble free life.  The 10 and 15 gallon size are made from 1.0mm thick stainless steel. The 20, 30 and 50 gallon size are made with 1.2mm stainless - that's pretty thick stuff - and you will know it when you pick one up. The included ball valve is a two piece design that allows for easy cleaning (we prefer these over 3 piece for ease of assembly) and is also made from 304 stainless.  Mirror Polish Finish The mirror polish finish isn’t just for making your Instagram feed pop! This extra slick finish is much easier to clean and sanitize than a standard brushed stainless kettle. Hop trub and other organic solids left behind after a brew day will have a hard time clinging to the interior surface and scrub away with ease. Size Ratios and Stuff All the BrewBuilt kettles follow the recent trend to a 1.2:1 ratio where the height is 1.2 times the diameter. This is a proven commercial ratio that has been adopted in homebrewing to achieve a more consistent 10% evaporation rate during the boil.  We do like this ratio for boiling. For Mashing we would prefer a little bit shallower but that is a small compromise. Dimensions for a hot-liquor tank, if you are thinking brewing system down the road, are irrelevant as any ratio kettle will do.   Final Words With welded tri-clamp fittings, mirror polish finish, a bunch of cool features, and a solid, thick 304 stainless steel core this kettle is a pretty amazing value. Remember, if you order from MoreBeer! we ship free anywhere in the continental USA! SlingBlade Heating Elements The BrewBuilt SlingBlade's unique crescent-shaped design promotes a rolling boil and even heat distribution. This electric heating element places all of the heating power on one side of the kettle, sending thermal energy upward to the surface that then cascades downward on the opposite side of the kettle. This movement creates a natural turbulence that evenly distributes heat while creating a vigorous boil. By being located on one side of the kettle, the other side is clear for immersion chillers, and the curved shape won't obstruct the flow of wort during whirlpool. Thanks to the non-circular design, the SlingBlade can easily be installed on any kettle with a 1.5" tri-clamp ferrule. This also makes removing the element for cleaning between uses a breeze. Kettle Key Features: Three welded T.C. couplers for a lifetime of leak free use 50-gal kettle has four welded T.C. couplers to use with two heating elements Butterfly Valve with 1/2" barb AISI304 Stainless Steel construction for longevity and excellent corrosion resistance Stainless handles and rivets for secure lifting Silicone coated kettle and lid handles for heat protection Lid is designed to conveniently hang from a handle 4 mm Tri-Clad Bottom with Aluminum Core heats quickly and disperses heat evenly to prevent scorching Induction burner compatible 1.0mm (10 & 15 gal) or 1.2mm (20, 30 & 50 gal) thick side walls resist denting 1.2:1 height to diameter ratio provides optimal evaporation rate during boiling Industry-First notched lid with silicone plug accommodates an immersion chiller or sparge arm Internally etched volume markers from top to bottom for easy filling SlingBlade Key Features: Made from Stainless Steel with proprietary coating for long life 1.5" Tri-Clamp connection Unique offset design promotes rolling boil Ultra-Low Watt Density eliminates scorching UL Certified components 240 Volt L6-30 plug 20 Amp breaker required for 10 & 15-gallon kettle 30 Amp breaker required for 20 & 30-gallon kettle 50-gallon kettle uses 2 x heating elements and requires 2 x 30 amp circuits SKU Size Element Wattage Kettle ID (in.) Height (in.) BE581B 10 3750 13.78 16.54 BE582B 15 4500 15.75 18.90 BE583B 20 5000 17.72 21.26 BE584B 30 5750 19.69 23.62 BE585B 50 (2) 5750 23.6 28.30   ***In order to avoid injury or death we strongly recommend using a GFCI in any circuit used near water. You can find one here.*** Lowest Price Guarantee, this item has MAP pricing so you can be confident you won't find it for less.

Read more less