Thin walled tubing perfect for siphoning or tranferring liquids when not under pressure. This is the most common size hose for homebrewing that you would need to fit onto the plastic spigots (FE347), 3/8'' OD bottle fillers, and the 3/8'' OD racking canes.
3/8" ID, 1/2" OD
1/8" thick wall
FDA approved food grade tubing for transferring liquids. Made of Vinyl (PVC). Will not impart flavors or odors into your product.
5/16 inch ID tubing is recomended for use with Mini and Regular Auto Siphons.
Thin wall tubing is recomended for siphoning and transferring liquids. For pumping, keg lines, or other pressurized applications, see our thick wall and keg tubing.
Starts siphon with a single stroke
Made from BPA-free acrylic plastic
Includes anti-sediment tip
Easy to dissasemble for cleaning and drying
7/8" outer diameter fits glass carboys, 1-gallon jugs or Growlers
The name says it all! No more struggling with all the different techniques to get a siphon started. The Easy-Siphon will get your transfer started quickly and with zero fuss. Simply submerge the the siphon, pull the inner tube up about halfway, then pump down to start the siphon. New design features 7/8" OD racking tube to better fit carboys, 1-gallon jugs, or growlers.
To prolong the life of your Easy Siphon, make sure that every time you assemble the unit, the inner walls of the outside acrylic tube and the O-Ring are wet.
Comes with 3/8" cane and 24" racking tube. 5/16" or 3/8" ID tubing must be purchased separately. Also available in 1/2" and 3/8" Mini models.
Maximum Temperature: 140°F (60°C)
Instructions:
Sanitize and rinse your Easy-Siphon.
Get the inner tube gasket and the outer tube wet.
Attach the curved siphon to a hose.
Submerge the end of Easy-Siphon into your container.
If bottling directly, attach the correct bottle for the tubing you are using and place it inside your bottle wand. Otherwise place the the tubing into the container you're racking to.
Pull the inner tube up about 7" until the liquid fills the tube.
Pump the inner tube down and siphon will begin.
Pull out inner tube and sanitize Easy-Siphon for storage.
This product is not resistant to high levels of alcohol. Do not sanitize with alcohol.
Acrylic is safe for long exposure to ABV up to 15%. It is safe up to 30% ABV for short periods of time (10 minutes or so). Not safe to expose acrylic to more than 30% ABV. Exceeding those limits will damage the Acrylic and could potentially leach into liquid. If you need to exceed these limits, we recommend using a stainless racking cane.
Starts siphon with a single stroke
Made from BPA-free acrylic plastic
Includes anti-sediment tip
Easy to dissasemble for cleaning and drying
7/8" outer diameter fits glass carboys, 1-gallon jugs or Growlers
The name says it all! No more struggling with all the different techniques to get a siphon started. The Easy-Siphon will get your transfer started quickly and with zero fuss. Simply submerge the the siphon, pull the inner tube up about halfway, then pump down to start the siphon. New design features 7/8" OD racking tube to better fit carboys, 1-gallon jugs, or growlers.
To prolong the life of your Easy Siphon, make sure that every time you assemble the unit, the inner walls of the outside acrylic tube and the O-Ring are wet.
Comes with 1/2" cane and 24" racking tube. 7/16" or 1/2" ID tubing must be purchased separately. Also available in 3/8" and 3/8" Mini models.
Maximum Temperature: 140°F (60°C)
Instructions:
Sanitize and rinse your Easy-Siphon.
Get the inner tube gasket and the outer tube wet.
Attach the curved siphon to a hose.
Submerge the end of Easy-Siphon into your container.
If bottling directly, attach the correct bottle for the tubing you are using and place it inside your bottle wand. Otherwise place the the tubing into the container you're racking to.
Pull the inner tube up about 7" until the liquid fills the tube.
Pump the inner tube down and siphon will begin.
Pull out inner tube and sanitize Easy-Siphon for storage.
This product is not resistant to high levels of alcohol. Do not sanitize with alcohol.
Acrylic is safe for long exposure to ABV up to 15%. It is safe up to 30% ABV for short periods of time (10 minutes or so). Not safe to expose acrylic to more than 30% ABV. Exceeding those limits will damage the Acrylic and could potentially leach into liquid. If you need to exceed these limits, we recommend using a stainless racking cane.
Give yourself peace of mind with this Reinforced Vinyl Brewing Tubing!
This 1/2" Reinforced Vinyl Tubing is FDA approved, food grade, rated to 158 degrees F, and 200 PSI. It is the perfect tubing to use in your homebrewery with our pumps, or anywhere you want the extra security that your tubing will not kink or burst. This type of tubing is essential when putting back pressure on a system. Standard vinyl tubing and silicone are great for their own purposes, but are not designed to handle pressure, and can balloon up or explode if too much pressure is used.
1/2" ID and 3/4" OD
FDA approved food grade tubing for transferring liquids. Made of Vinyl (PVC). Will not impart flavors or odors into your product.
7/16 inch ID tubing is recomended for use with 1/2 inch Auto Siphons.
Thin wall tubing is recomended for siphoning and transferring liquids. For pumping, keg lines, or other pressurized applications, see our thick wall and keg tubing.
Siphon starter for transferring liquids and bottling. Very easy to use and sanitize. A single stroke starts the siphon without disturbing the sediment. Precision designed for smooth, leak-free operation.
The Regular Auto Siphon is recommended for use with standard buckets and carboys. We strongly recommend you use 5/16 in ID tubing (not 3/8 in) to prevent air leaks from stopping the siphon. Outer diameter of the siphon shaft is 7/8 inches.
Leave the gunk behind and keep your beer clear with this racking cane filter. A great solution at the right price.
This Racking Cane Filter Screen is very effective when racking with whole hops, oak, or fruit in the fermenter. Simply slide this over the bottom of the racking cane and begin the siphon! Made from Stainless Steel mesh. Some customer are also using this in the their keg attached to the bev out dip tube.
Fits on a 3/8" stainless steel racking cane.
Note: You may want to use a hose clamp to tighten this to the racking cane.
Clamps to buckets, carboys and other containers. Holds the Auto Siphon securely above the sediment while transferring. To use, simply snap on the Auto Siphon, slide down to the desired level, and then snap off when done. Use the 3/8 inch Auto Siphon Clip for Mini and Regular 3/8 inch Auto Siphons.
The Easy Siphon Clip holds your Easy Siphons to Carboys, Pails, Fermonsters, Buckets and more! Made from lasting plastic materials, so you can clip and unclip your Easy Siphons without issues.
Works with:
Easy Siphon 3/8" & 1/2" (R511 / R513)
2022 models - 7/8" thick
Mini Easy Siphon
The Sample Taker (MT342)
Legacy Easy Siphon 3/8" & 1/2" (R510 / R512)
pre-2022 Models - 1" thick
Please note: if the clip is used with the Legacy Easy Siphons (pre-2022 models), it will not work with the new models afterwards as the clamps will stretch to adapt to the bigger diameter of the older models.
An inline plastic valve with 3/8" barbed inlet and outlet. Not designed to work with hot liquids or situations involving pressure (use a brass or stainless ball valve in those situations.)
Clear plastic racking cane with curve. Good for 6.5 gallon carboys. 3/8" diameter is the standard size for filling beer bottles.
3/8" OD
30" total length (including bend)
27" from tip to bend
Clear plastic racking cane with curve. Good for 5 gallon carboys. 3/8" diameter is the standard size for filling beer bottles.
3/8" OD
24" total length (including bend)
21" from tip to bend
FDA approved food grade tubing for transferring liquids. Made of Vinyl (PVC). Will not impart flavors or odors into your product.
Thick wall tubing is recomended for pumping and pressurized systems. For siphoning and transferring liquids, see our thin wall and transfer tubing.
Siphon starter for transferring liquids and bottling. Very easy to use and sanitize. A single stroke starts the siphon without disturbing the sediment. Precision designed for smooth, leak-free operation.
The Large Auto Siphon is recomended for use with standard buckets and carboys. We strongly recomend you use 7/16 in ID tubing (not 1/2 in) to prevent air leaks from stopping the siphon.
Holds 3/8'' racking cane and clips to carboy or bucket. Great for holding the siphon off the bottom when starting your transfer. Then you can slowly lower the bottom of the siphon cane to the bottom of the carboy/bucket by sliding the cane in the clip to help eliminate disturbing the bottom sediment layer. A must have.
FDA approved food grade tubing for transferring liquids. Made of Vinyl (PVC). Will not impart flavors or odors into your product.
Thick wall tubing is recomended for pumping and pressurized systems. For siphoning and transferring liquids, see our thin wall and transfer tubing.
Stainless Steel racking cane - 3/8 inch OD x 26 inches long from tip to bend (30" total), with curved top. 3/8 inch diameter is the standard size for filling beer bottles.
FDA approved food grade tubing for transferring liquids. Made of Vinyl (PVC). Will not impart flavors or odors into your product.
Thick wall tubing is recomended for pumping and pressurized systems. For siphoning and transferring liquids, see our thin wall and transfer tubing.
Racking canes are the most common tool used to transfer your homebrew from a carboy or other fermentation vessel to your bottling bucket or kegs. This racking cane comes with a tip cover that will help to keep trub out of the bottling bucket or keg, leaving you with a clearer finished product!
1/2" OD
30" total length (including bend)
27" from tip to bend
Starts siphon with a single stroke
Made from BPA-free acrylic plastic
Includes anti-sediment tip
Easy to dissasemble for cleaning and drying
7/8" outer diameter fits glass carboys, 1-gallon jugs or Growlers
Mini Easy Siphon will reduce loss when racking from small vessels
The name says it all! No more struggling with all the different techniques to get a siphon started. The Easy-Siphon will get your transfer started quickly and with zero fuss. Simply submerge the the siphon, pull the inner tube up about halfway, then pump down to start the siphon. New design features 7/8" OD racking tube to better fit carboys, 1-gallon jugs, or growlers.
To prolong the life of your Easy Siphon, make sure that every time you assemble the unit, the inner walls of the outside acrylic tube and the O-Ring are wet.
Comes with 3/8" cane and 15" racking tube. 5/16" or 3/8" ID tubing must be purchased separately.
Maximum Temperature: 140°F (60°C)
Instructions:
Sanitize and rinse your Easy-Siphon.
Get the inner tube gasket and the outer tube wet.
Attach the curved siphon to a hose.
Submerge the end of Easy-Siphon into your container.
If bottling directly, attach the correct bottle for the tubing you are using and place it inside your bottle wand. Otherwise place the the tubing into the container you're racking to.
Pull the inner tube up about 7" until the liquid fills the tube.
Pump the inner tube down and siphon will begin.
Pull out inner tube and sanitize Easy-Siphon for storage.
This product is not resistant to high levels of alcohol. Do not sanitize with alcohol.
Acrylic is safe for long exposure to ABV up to 15%. It is safe up to 30% ABV for short periods of time (10 minutes or so). Not safe to expose acrylic to more than 30% ABV. Exceeding those limits will damage the Acrylic and could potentially leach into liquid. If you need to exceed these limits, we recommend using a stainless racking cane.
An inline plastic valve with 1/2" barbed inlet and outlet. Not designed to work with hot liquids or situations involving pressure (use a brass or stainless ball valve in those situations.)
This is a great addition to most siphon setups as it can be used to control the flow of liquid. 1/2" Diameter tubing will fit onto this, and the switch on the side turns the liquid flow on or off.
