This insulated tubing kit was developed specifically for the BrewBuilt Jacketed Conical. It has all the fittings needed to connect an IceMaster Glycol Chiller to the conical jacket's 1.5" tri-clamp inlet and outlet—plus premium quick disconnects with shutoff valves that provide a "dry break" when they're disconnected. That means no cooling solution leaking all over your brewery every time you take the system apart for cleaning. The Female QDs are installed on the insulated tubing, and the Male QDs are installed on the T.C. x FPT Adapters that connect to the cooling jacket's inlet and outlet.
Insulated tubing will now only provide increased chilling efficiency, it will also eliminate line sweating so you don't need to wipe up puddles of condensation that might collect on your brewery's floor during fermentation or cold crashing.
Kit Includes:
1 - Insulated Tubing Set (2 x 6' lines)
2 - High Temp Plastic Female QDs w/ 3/8" Barb
2 - High Temp Plastic Male QDs w/ 1/2" MPT
2 - 1.5" Tri-Clamps
2 - 1.5" T.C. Gaskets
2 - 1.5" T.C. x 1/2" FPT Adapters
Insulated tubing will improve your chilling efficiency and eliminate the troublesome line sweating. This set includes two 6' lengths of 3/8" ID silicone tubing wrapped in elastomeric insulation. Hose clamps are included to secure connection points with your preferred fittings.
Built-in external cooling jacket with 1.5" TC Ports
Pressure Pack lid with floating dip tube and draft style QD connections for sampling/serving
Tri-clamp thermowell, sealed pressure gauge, and pressure relief valve included
Full-draining dish bottom design with center bottom tri-clamp drain
Highest quality mirror polish finish inside and out
Welded, ground, and polished interior welds provide the highest quality and are optimal for sanitation
BrewBuilt Brite Tanks are perfect for carbonation, clarification, maturation, and storage of your finest brews. This tank will fit seamlessly into your brewing setup to help optimize space without compromising capacity. Featuring smooth, polished interior surfaces that make cleaning a breeze and ensures complete sanitation. These units set the standard for affordable brewing tanks without sacrificing quality.
Built to handle high pressures for effective carbonation and conditioning, the BrewBuilt Brite Tank comes standard with a sealed pressure gauge and professional-quality tri-clamp PRV. The Pressure Pack, which installs in the 8" TC lid, features a floating dip tube with filter attachment that draws the clearest beer in the tank from the top down. The Pressure Pack's ball lock keg posts allow for easy integration into your draft system so you can serve directly from the tank.
The tank features a dish-shaped bottom and centered 1.5" drain pipe to allow for easy removal of trub, yeast, and other sediments that settle at the bottom of the tank to help clarify the beer and improve quality. The bottom drain also efficiently transfers beer to kegs, bottles, or cans.
Features:
External cooling jacket with 1.5" tri-clamp connections
Pressure Pack with Clear Float, a floating dip tube that draws beer from the top down
Comes complete with 15 PSI pressure valve and sealed pressure gauge
8" lid cap opening with 8” TC clamp
Extra 1.5" TC hop port on the lid
1.5" TC thermowell for inserting thermal probe
Extra 1.5" TC port at the front for installing a carbonation stone or sample valve
Centered bottom drain with 1.5" butterfly valve
4-leg standing design with reinforced crossbars & threaded feet
Interior welds are the best in the business - uniquely ground and polished
Specs:
Grade 304 Stainless Steel
Mirror Polish Finish Interior & Exterior
Working Volume: 1 bbl
Max Volume: 1.1 bbl
Working Pressure: 1 Bar (14.5)
Overall Height (w/ fittings): 39.5"
All ports are 1.5" TC except 8" TC Top Port and 4" TC Pressure Pack Port
Built-in external cooling jacket with 1.5" TC Ports
Pressure Pack lid with floating dip tube and draft style QD connections for sampling/serving
Tri-clamp thermowell, sealed pressure gauge, and pressure relief valve included
Full draining dish bottom design with center bottom tri-clamp drain
Highest quality mirror polish finish inside and out
Welded, ground, and polished interior welds provide the highest quality and are optimal for sanitation
BrewBuilt Brite Tanks are perfect for carbonation, clarification, maturation, and storage of your finest brews. This tank will fit seamlessly into your brewing setup to help optimize space without compromising capacity. Featuring smooth, polished interior surfaces that make cleaning a breeze and ensures complete sanitation. These units set the standard for affordable brewing tanks without sacrificing quality.
Built to handle high pressures for effective carbonation and conditioning, the BrewBuilt Brite Tank comes standard with a sealed pressure gauge and professional-quality tri-clamp PRV. The Pressure Pack, which installs in the 8" TC lid, features a floating dip tube with filter attachment that draws the clearest beer in the tank from the top down. The Pressure Pack's ball lock keg posts allow for easy integration into your draft system so you can serve directly from the tank.
The tank features a dish-shaped bottom and centered 1.5" drain pipe to allow for easy removal of trub, yeast, and other sediments that settle at the bottom of the tank to help clarify the beer and improve quality. The bottom drain also efficiently transfers beer to kegs, bottles, or cans.
Features:
External cooling jacket with 1.5" tri-clamp connections
Pressure Pack with Clear Float, a floating dip tube that draws beer from the top down
Comes complete with 15 PSI pressure valve and sealed pressure gauge
8" lid cap opening with 8” TC clamp
Extra 1.5" TC hop port on the lid
1.5" TC thermowell for inserting thermal probe
Extra 1.5" TC port at the front for installing a carbonation stone or sample valve
Centered bottom drain with 1.5" butterfly valve
4-leg standing design with reinforced crossbars & threaded feet
Interior welds are the best in the business - uniquely ground and polished
Specs:
Grade 304 Stainless Steel
Mirror Polish Finish Interior & Exterior
Working Volume: 2 bbl
Max Volume: 2.2 bbl
Working Pressure: 1 Bar (14.5)
Overall Height (w/ fittings): 62"
All ports are 1.5" TC except 8" TC Top Port and 4" TC Pressure Pack Port
Due to high demand, this item is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this to you when we receive more inventory.
This is a no compromise, professional level hardware kit that allows for safe pressure fermentation in an X-Series Uni Conical. If you plan to ferment, or to seal/cap an active fermentation, in your BrewBuilt X-Series Conical you must use this Brewbult Kit for Fermenting Under Pressure. During fermentation Krausen can potentially clog the PRV that is built into the lid. The hardware in this kit is the same as what you will find on a commercial Unitank. This is not an all-in-one unit. All-in-one units are cheaper but not as safe.
Component Break Down:
Commercial Grade Spunding Valve - The kit is built around a commercial Spunding Valve that allows you to set your desired fermentation pressure. if that ferementation pressure exceeds your set point, it will blow off any excess pressure from the X-Series Conical. The clear cup holds liquid acting as an airlock and allowing krausen to exit. The Spunding valve is also adjustable.
Pro Grade PRV (Pressure Relief Valve) - On all brewery pro tanks, a tri-clamp PRV is always installed in addition to a Spunding Valve. This is because a Spunding Valve still has the potential to clog. The pro PRV has a very wide interior body as to reduce the risk of clogging. The PRV is non-adjustable and comes preset to relieve pressure at 15 PSI.
Sealed Pressure Gauge - This is a liquid filled, sealed gauge. The bottom of the gauge is a thin plate of stainless that moves up or down in relation to pressure in the tank. That causes the oil in the gauge to compress which is what the gauge reads. When properly sealed, there is no way krausen can get into this gauge and cause a false reading. However, it is important to ensure the guage is sealed, otherwise, there is a risk that krasuen clogs the gauge giving you an inaccurate reading.
Foam Axe - Foam Axe is a silica-based krausen cutter used by commercial breweries to reduce krausen blow off while increasing foam retention in your beer. Using Foam Axe is required for every batch fermented under pressure, but we recommend it for all batches fermented in your X-Series Conical. Foam Axe helps keep krausen out of PRVs and other hardware which is always a good idea.
When your BrewBuilt Uni is outfitted with a Kit for Pressure Fermentation there are three devices for relieving pressure, including the PRV that is always built into the lid, the adjustable Spunding Valve, and the pro grade PRV.
Includes:
Commercial Grade BrewBuilt Spunding Valve
1 BAR (0.3–14.5 psi)
Hand Adjustable Blowoff
1.5" tri-clamp Connection
Made from 304 stainless steel with plastic liquid cup
Tri-Clamp Pressure Relief Valve (PRV)
Calibrated to 1 BAR (14.5 psi)
1.5" tri-clamp connection
Made from 304 stainless steel
Sealed, Liquid Filled Pressure Gauge
Calibrated to 2 BAR (30 psi)
1.5" tri-clamp connection
Made from 304 stainless steel
CellarScience Foam Axe Krausen Reducer
Reduces krausen build up inside the fermenter
Connection Hardware
(3) 1.5" T.C. Clamps
(3) 1.5" EPDM T.C. Gaskets
WARNING! The use of the BrewBuilt Kit for Fermenting Under Pressure is required for performing Pressure Fermentations in your X-Series conical. The PRV built into the lid is not designed to be the only release point during a pressure fermentation.
WARNING! The use of Foam Axe is required to reduce krausen (foam from fermentation) production in the fermenter.
WARNING! Always release pressure, then remove the PRV built into the lid to ensure the conical is completely depressurized before removing fittings or the lid clamp. Failure to do so can result in personal injury.
10-gallon propane systems are regularly stocked and ready to ship!
Single tier brew system. Look into and interact with every kettle without the need for a step stool or ladder
Digital Touchscreen Controller comes standard. Control every aspect of your brew day from a single screen
Automatic HERMS mashing. Set up to five mash steps in the digital controller and temperatures will be raised and be maintained automatically
Powerful Gas Burners. Whether you choose Propane or Natural Gas as your fuel source, your burners will be fast, efficient, quiet and have great flame control
The Ultimate Sparge Arm. Eliminate hot side aeration with this fully adjustable sparge arm
Built to order in the USA. Every system features a custom-welded stainless steel frame manufactured in the BrewBuilt metal shop
Brew like a pro with the BrewBuilt Low Rider BrewSculpture. Our brewing systems were first introduced in the 1990’s and now have over two decades worth of R&D and customer feedback built into their design. There’s a reason why top level breweries like Sierra Nevada and Russian River use a BrewBuilt BrewSculpture for training, ingredient testing and pilot batches.
Touchscreen Control Panel
From heating strike water to whirlpooling hop additions, you’ll orchestrate your entire brew day from our custom designed 7” touchscreen control panel. The HLT burner and pumps can be controlled from a single touchscreen controller. Program your mash steps and the controller will do the rest—igniting burners and kicking on pumps to recirculate wort as needed. It also offers boil addition timers to remind you when to add hops or clarifiers, as well as manual control of your pumps.
Control Panel Key Features:
Programmable HERMS Mash Steps - choose from 3 preset mash schedules or custom design your own with up to 5 steps. From there the control panel guides your mash through the temp raises and time rests automatically.
Always Hot - Controller maintains the Hot-Liquor tank temperature you choose by turning the burner off and on automatically.
Auto Sparging - Sparge water flow is controlled automatically with integrated Mash Tun float switch.
Timer Alarms - Built in boil timers remind you when to add hops, finings, or anything else.
Manual Mode - allows you to control pumps for anything you want such as cleaning.
Automatic HERMS Mashing
Mash temps are maintained via the HERMS coil made from convoluted copper tubing. This top-of-the-line coil design offers unparalleled efficiency while gently heating your wort. Choose from your saved mash schedules or program one on the fly. When the mash begins, the controller will automatically maintain the temperature of the hot liquor bath that the HERMS coil rests in. When the wort temp drops below your set point, the controller will turn on the pump to circulate wort through the coil. You can also set the pump to continuously circulate wort for the whole mash if you prefer, and the HLT will continue to maintain your mash temp automatically. When each mash step is complete, the controller will turn on the burner to raise the temperature of the HLT and begin the next step.
Powerful Gas Burners
Choose your fuel source! Natural Gas is a nice option for the brewer whose home is already supplied with natural gas. This is a convenient option since you will never have to refill propane tanks, and you will never run out of gas mid batch. However, you do lose the freedom to move your BrewSculpture™ once it has been hard plumbed to your gas line. Whether you prefer the mobility of using propane or the reliable supply of natural gas, your burners will be fast, efficient, quiet and have great flame control.
The Ultimate Sparge Arm
No other system protects against hot side aeration quite like the BrewSculpture. While other systems simply pump wort back to the top of the mash tun and let it splash back down over the grain bed, the Ultimate Sparge Arm will make sure your wort circulates with virtually zero aeration. The Ultimate Sparge Arm features adjustable height and adjustable flow. Depending on what beer you’re brewing, the surface of the mash will be at different heights. Simply lower the sparge arm to just below the surface of the mash and your recirculation will be splash-free. The ball valve at the inlet of the sparge arm allows you to dial in the flow and reduce turbulence as you see fit.
Custom Welded Frame Made in the USA
Every BrewBuilt BrewSculpture is made to order and built around a custom TIG welded 304 stainless steel stand. While other companies cut corners by using generic stainless steel tables for their systems, our extra beefy stand is fabricated in our California-based metal shop and designed to outlive even you. Every stand comes with rolling casters and folding handlebar so you can easily move your system whenever needed.
What Sets the Digital BrewSculpture Apart?
Only system with a heavy-duty, purpose-built, welded stainless frame as standard.
Only system with digital touch screen as standard.
Only system with programmable mash steps on touch screen.
Welded fittings for a lifetime of easy-to-clean, leak-free performance.
Ultimate Sparge Arm reduces hot side aeration.
Keep sparge water warm while preheating the boil.
Key Features of the Low Rider BrewSculpture
Made in USA by BrewBuilt
304 Stainless Steel TIG welded stands. The ultimate frame material that will outlast you. No paint or powder coating.
Every BrewSculpture includes folding handles and built-in rear casters that allow you to move your BrewSculpture with ease.
Oversized 304 stainless BrewBuilt Kettles with welded fittings, notched lids, internally etched volume markers, aluminum clad bottoms, and silicone handles. Built to last.
Our "Large" option will come with 22 gallon kettles
The fluid path is easy to use and clean. We've included the time tested, top of the line March pumps along with heat resistant food-grade silicone tubing and our own specially designed stainless quick disconnects.
Burners are fast, efficient, quiet and have great flame control.
Mashtun includes the Ultimate Sparge Arm with innovative design to eliminate hot-side aeration. The center draw outlet with quick disconnect is locked in during mashing but easily disconnects for cleaning. The mash screen has a very low volume of base water under the screen to aid with efficiency and mash consistency. The perforated stainless mash screen is reinforced for use with pump recirculation and includes a silicone gasket to make a perfect seal with the kettle wall. Internally etched volume markers make mash water additions super easy.
Boil Kettle includes innovative Whirlpool maker for leaving hops and trub behind. Volume markers are etched on the inside so you know exactly how much wort you have at all times. The lid notch is super handy for hanging hop bags, using an immersion chiller, etc., but when not is use an included silicone plug seals the notch. The bottom of the boil kettle is tri-clad with a 4mm aluminum core sandwiched between two layers of 304 stainless. The aluminum core eliminates scorching and the cleaning that comes with a scorched kettle.
Includes all of the tubing you'll need with:
4 x 40 in. Hoses with male and female quick disconnects
32 in. Hose with 2 female quick disconnects
32 in. Hose with 1 female quick disconnect and 1 open end
Dimensions / Specifications:
Stainless Frame measures 73" L x 19.5" W x 29" H
Requires 110/120V power source
Please Note: Natural Gas Sculptures require installation by a professional plumber. These units terminate in a ¾” Male Flare connection.
We Supply front and back handles on the XXL Kettles to allow removing the kettles from the stand more easily.
Now available for pre-order! The BrewBuilt® V5 BrewSculpture will be released in late June. Place your pre-order now to lock in priority fulfillment as soon as the unit is available.
Introducing the Next-Generation BrewBuilt BrewSculpture™
Professional-Grade Control: Manage your entire brew day from a single, intuitive digital touchscreen. Easily program mash steps and control pumps and heating elements with a tap, providing a centralized and seamless brewing experience.
Full-Draining Kettles: The completely redesigned, true welded dish bottoms ensure you get every last drop of your wort. This revolutionary design eliminates the need for tilting and makes cleanup significantly easier.
Innovative Mash Tun with Grain Door: Say goodbye to scooping heavy, spent grain. Our integrated grain door and stainless steel grain chute let you easily empty the mash tun into a disposal bucket, keeping your brew day clean and efficient.
Tangential Boil Kettle: The integrated tangential whirlpool arm creates a powerful vortex, compacting hop and trub matter into a tight cone for a clear, sediment-free transfer to your fermenter. An integrated cooling jacket also helps rapidly chill your wort.
Experience the pinnacle of home brewing with the new BrewBuilt BrewSculpture™. This all-in-one electric brewing system combines the trusted control and performance of our original designs with the latest innovations in brewing vessel technology, all managed through a unique digital touchscreen controller. The result? A pro-grade, all-electric sculpture engineered for efficiency, precision, and an unbelievably clean brew day, with the entire system controlled from one intuitive interface.
At the Heart of the System: Full-Draining Kettles and Integrated Work Table
We've completely redesigned our kettles to be the most drainable on the market. Featuring a true welded dish bottom, these kettles ensure you get every last drop of your precious wort. The revolutionary design means no more tilting, no more lost volume, and a far easier cleanup. Complementing this, a new integrated work table, sourced overseas, features a recessed top and drain, providing a dedicated and convenient space for all your brewing tasks.
Mash Tun with Grain Door: Say goodbye to scooping heavy, water-logged grain. Our innovative mash tun features an integrated grain door, allowing you to simply open the chute and empty spent grains directly into a bucket or disposal bag. The included stainless steel grain chute ensures a clean and mess-free transfer.
Boil Kettle with Tangential Arm and Cooling Jacket: Our new boil kettle is built for performance. The integrated tangential whirlpool arm creates a powerful vortex, compacting hop and trub matter into a tight cone at the center of the kettle, leaving you with a clear, sediment-free transfer to your fermenter. Additionally, the integrated cooling jacket allows for rapid chilling, bringing your wort down to pitching temperature faster than ever.
Unmatched Power and Control with a Single Interface
Powered by our proven control system, the new BrewSculpture puts you in command of your entire brew day through its unique digital touchscreen controller. The intuitive touchscreen interface allows you to program mash steps and control every pump and element with a tap of your finger, providing a seamless and centralized brewing experience.
SlingBlade™ Heating Elements: Our unique crescent-shaped SlingBlade™ heating elements are engineered to promote a vigorous, rolling boil without scorching your wort. Their ultra-low watt density design transfers heat efficiently while staying out of the way of your whirlpool arm and other kettle accessories.
Built for Life: Like all BrewBuilt products, this Brew Sculpture is built to last. The heavy-duty, TIG-welded 304 stainless steel frame is designed for a rock-solid, corrosion-resistant foundation for a lifetime of brewing.
The new BrewBuilt BrewSculpture™ is more than just a brewing system—it's a professional-grade, all-electric brewery that fits in your home, controlled effortlessly from a single, advanced digital interface. It’s a testament to over two decades of R&D and a commitment to helping you brew your best beer.
Please Note: The BrewSculpture™ power box includes a 6 ft cord with an L6-30P plug (two for the 1BBL model); if your outlet is further than 6 ft away, we offer a compatible 10 ft extension cord. For your safety, DO NOT string multiple extension cords together, as the increased electrical resistance creates a significant fire hazard. Please ensure your setup reaches your power source using only a single extension.
Upgrade standard and Plus model X-Series conicals with increased cooling performance Chill down to cold crashing temps when used with glycol and insulation; compatible with any vessel with a 4" T.C. opening Keg Connects and Floating Racking Buoy enable you to pressure transfer the clearest beer at the top of your fermenter 1.5" tri-clamp ferrule for use with additional T.C. accessories like the Pressure Fermentation Kit or Hop Bong Sanitary all stainless steel construction with 3/8" OD inlet/outlet for glycol connection Upgrade your standard model X-series conical with the ultimate in-solution chilling coil—the BrewBuilt Ludicrous Coil! Temperature control is one of the most important aspects of a healthy, happy fermentation. When your fermenting beer gets too hot, the yeast will likely impart off-flavors that can easily overwhelm the taste of your finished beer. The Ludicrous Coil offers a ludicrous amount of surface area (which means more cooling capacity) compared to other chilling coils you'll find. Not only does it manage your fermentation temperature with ease, the Ludicrous Coil has the capacity to chill beer to cold crashing temperatures when used with glycol and insulation. A truly unparalleled unit when it comes to in-solution chilling. You will also need a cold water source to provide the cooling solution. For maintaining ale temperatures, a cooler or bucker of ice water is sufficient in most cases and this method works well with the BrewBuilt Chiller Pump Kit. For maintaining lager temperatures or cold crashing, we recommend the IceMaster Max 2 Glycol Chiller and the Insulated Tubing Set. Sanitary all stainless steel construction with 3/8" OD inlet/outlet. Compatible with 3/8" ID flexible tubing & hose clamps or 9.5mm Duotight adapter. Specifications: Size Coil Height Float Tubing Length 7/14 Gal 18.5" 24" 27 Gal 24" 30" 38 Gal 33" 39"
Replacement Gaskets for your BrewBuilt Mash Tun. These are custom pieces we've designed for the BrewBuilt Mash tuns. Their only purpose? Assist you in brewing the best beer possible. Solid single piece silicone molded construction will last you for a number of brews, but whether you lose yours, or manage to break it, we have replacements. For a complete False Bottom Kit that includes the necessary Screen and Pickup Tube, see our BrewBuilt Mash Tun False Bottom Kits. Or for a complete Mash Tun, see our BrewBuilt Mash Tuns. Lowest Price Guarantee, this item has MAP pricing so you can be confident you won't find it for less.
Convert the BrewBuilt T.C. brewing kettle into a mash tun using one of these false bottom kits. The heavy duty false bottom rests low in the kettle, utilizing a tri-clamp style maximizer that reduces dead space and pulls from the very bottom of your kettle, leaving no wort behind. A Silicone gasket rims the False Bottom, ensuring a tight seal to the wall with no chance of grain bypass. A handle is welded to the top of the false bottom for easy removal.
To monitor your mash temperature, we recommend the 1.5" T.C. Thermometer with 6" probe for better grain bed penetration.
1.5" tri-clamp and gasket included
Welded T.C. maximizer
False bottom gasket for tight seal
Welded legs and handle
Made from 304 stainless steel
NOTE: These false bottom kits will fit all BrewBuilt T.C. kettles, including the electric kettle with SlingBlade heating element. We do not recommend converting the electric kettle into a mash tun as the element will scorch the grain. If you wish to use the false bottom in your boil kettle, it should be noted that the screen is designed to filter grain, so fine particle vegetal matter will pass through.
Have you been struggling with fermentation temperature swings? The BrewBuilt Neoprene Carboy Sleeve works great for maintaining the internal temperature of your 5, 6, or 6.5 gallon glass carboy. If you aren't fermenting in a temperature-controlled environment your beer is likely rising and falling with the ambient temperature, and these swings can stress out yeast and have a negative effect on the finished product. This 6 mm thick neoprene sleeve will help retain the heat naturally produced by fermentation activity and provide some protection from the ambient environment, leading to more consistent fermentation temps, happier yeast, and less off flavors in your beer.
We highly recommend the neoprene sleeve for use with the BrewBuilt Carboy CoolStix. The added insulation will lower the amount of cycles needed to maintain fermentation temperatures and is a must-have for cold crashing.
SKU
Size
Height (in.)
Diameter (in.)
FE329A
5 Gal
14.75
10.75
FE329B
6 Gal
17.25
10.90
FE329C
6.5 Gal
17.50
11.20
The perfect pint glass to enjoy that beer you brewed in a BrewBuilt boil kettle or fermented in an X1 Uni conical. Classic 16 oz "shaker pint" style glass with BrewBuilt logo.
Replacement tri-clamp lid for the BrewBuilt X3 Uni Conical and Brite Tanks. Features a 4" T.C. ferrule, (2) 1.5" T.C. ferrules, and a built-in pull-ring PRV. Compatible with all sizes of X3 Conicals and BrewBuilt Brite Tanks via 8" tri-clamp connection.
Not compatible with X2 or X1 Uni Conicals.
Lid only. The replacement lid comes with the PRV but does not include tri-clamps, gaskets, or other parts & accessories.
The ultimate coaster, it won't stick to the bottom of your glass but it will stick to the top. Perfect for marking your beer while you make room for more beer. It will make an air tight but not pressure tight seal with most pint glasses. Designed to seal to the top of a 16oz Libby shaker glass.
The BrewBuilt SlingBlade is an innovative electric heating element designed to promote a rolling boil and even heat distribution. Shaped for Performance and Convenience The SlingBlade's unique crescent-shaped design positions all of the heating power on one side of the kettle, sending thermal energy upward to the surface that then cascades downward on the opposite side of the kettle. This movement creates a dynamic turbulence that evenly distributes heat while creating a vigorous, rolling boil. Other heating elements stick right out into the middle of the kettle or use a full circle design that rings the kettle wall. This can cause an obstruction for immersion chillers or make it difficult to stir without banging into the element. The SlingBlade was designed to avoid these issues. By remaining on one side of the kettle, the element will be out of the way of your immersion chiller, and since the element follows the curvature of the kettle wall, it won't interfere with the flow of wort during whirlpool. Ultra-Low Watt Density An electric element transfers power to your wort by applying heat, but if this heat is too concentrated you will get local heating that is hotter than 212°F. This catalyzes Maillard Reactions, which can lead to darker beer than intended and produce unwanted caramelization. Think of these reactions like roasting a marshmallow. First it gets a light brown, we call this Maillard reactions, a little hotter and it gets a dark brown, we call this caramelization, then it turns black and we call this pyrolysis (burnt or scorched). While all kettles undergo these reactions, an electric element can concentrate more heat into a small area, which can quickly scorch your wort. Our experience is that at 90-watts per square inch recipes need to be modified to account for the element and light beers never come out quite right. The SlingBlade element was designed at 50-watts per square inch to reduce the chance of scorching while still providing a vigorous boil. For even lower watt density, consider the Boil Vigor Controller. Tri-Clamp Connection The SlingBlade installs quickly and easily on any kettle with a T.C. ferrule thanks to the curved, non-circular design. This also makes it a breeze to remove the element for cleaning between uses. The SlingBlade heating elements were designed to fit perfectly with BrewBuilt brewing kettles, but you may find them suitable for other kettles as well. They should be used with T.C. ferrules no longer than 1" in length. For dimensions and recommended minimum kettle diameter, please see the chart below. Features: Made from Incoloy alloy with proprietary coating for long life 1.5" Tri-Clamp connection Unique offset design promotes rolling boil Ultra-Low Watt Density eliminates scorching UL Certified components Specs: 240 Volt L6-30 plug 20 Amp breaker required for 10 & 15 gal element 30 Amp breaker required for 22 & 31 gal element 50-gallon kettle requires 2 x BE538 and 2 x 30 amp circuits SKU Kettle Vol. Wattage Length Radius Min. Kettle Ø BE535 10 gal 3750 13.25" 6.3" 13.78" BE536 15 gal 4500 16.75" 7.3" 15.75" BE537 22 gal 5000 17.25" 8.3" 17.72" BE538 31 gal 5750 19.5" 9.3" 19.69" Please note: Length is measured from the tip of the heating element to the T.C. connection. Radius is measured from the middle of the T.C. connection to the outermost edge of the element's curve. ***In order to avoid injury or death we strongly recommend using a GFCI in any circuit used near water. You can find one here.*** Lowest Price Guarantee, this item has MAP pricing so you can be confident you won't find it for less.
Due to high demand, this item is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this to you when we receive more inventory.
The easiest way to power the BrewBuilt™ SlingBlade! This professionally wired watertight switch gives you a simple On/Off control of your heating element. Switches both legs of a 220V 30AMP circuit and comes with 5 ft. input and output cords with molded LP6-30P ends. It also features two handy tabs for mounting to a wall.
Don't wear out your expensive plugs and sockets hot patching your 220V burner elements. Plugging your element directly into a live power outlet will cause a small spark, and when done repeatedly this can damage the plug and the socket, especially with high voltage 220V appliances. Not only is the power switch more convenient to turn your element on and off during the brew day, it will eliminate the risk of damage done by hot patching.
This BrewBuilt Stainless Steel Ball Valve features a locking mechanism that keeps the valve from being opened by a child or passing dog while you are brewing. Easy to clean 2 piece design, constructed from high grade 304-stainless made to last. 1/2" FPT on input and output side.
TIP: You can take a ball valve apart using two crescent wrenches. This will allow you to open up the valve to get to the ball and the two PTFE gaskets that form the seal when closed.
Features:
1/2" FPT on inlet and outlet
Locking Mechanism on Handle
304 SS construction with PTFE gaskets
Two-Piece Construction for easy cleaning
Full Port design for minimal pressure loss / resistance
BrewBuilt: Designed for Brewing, Built to Last.
The BrewBuilt Butterfly Valve has all the standard advantages you would expect from a butterfly valve in that they are the most sanitary valve, easy to clean and won't trap wort inside. It has a custom polished stainless steel handle which is designed to fit perfectly with the BrewBuilt conical fermenters and tri-clamp kettles.
1.5" tri-clamp
Stainless steel handle
7 locking positions
Squeeze trigger locking handle
Made from 304 stainless steel
Please Note: 2" valve shown as example photo. Updated images coming soon.
The BrewBuilt Butterfly Valve has all the standard advantages you would expect from a butterfly valve in that they are the most sanitary valve, easy to clean and won't trap wort inside. It has a custom polished stainless steel handle which is designed to fit perfectly with the BrewBuilt X-series conical 2" T.C. bottom port.
2" tri-clamp
Stainless steel handle
7 locking positions
Squeeze trigger locking handle
Made from 304 stainless steel
The BrewBuilt Butterfly Valve has all the standard advantages you would expect from a butterfly valve in that they are the most sanitary valve, easy to clean and won't trap wort inside. It has a custom polished stainless steel handle which is designed to fit perfectly with the BrewBuilt X3 Conical's 3" T.C. bottom port.
Not compatible with BrewBuilt X1 or X2 Uni Conicals which feature a 2" bottom port.
3" tri-clamp
Stainless steel handle
7 locking positions
Squeeze trigger locking handle
Made from 304 stainless steel
A sealed pressure gauge is the most sanitary and safest solution for your needs. Designed to prevent krousen from plugging the gauge, it ensures longer-lasting performance and unparalleled reliability.
This 1.5" tri-clamp pressure gauge is included with the BrewBuilt™ Kit for Fermenting Under Pressure but can be used with any stainless steel conical fermenter with 1.5" T.C. ports. Liquid filled gauges offer better performance and longer lifespan compared to dry gauges. Dial face reads in both psi and BAR.
Sealed, liquid filled pressure gauge
0-30 psi
0-2.05 BAR
1.5" tri-clamp connection
Made from 304 stainless steel
Due to high demand, this item is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this to you when we receive more inventory.
Don't fear the Beast, feed the Beast! This heavy duty counterflow wort chiller will gobble up heat from your wort as it passes from kettle to fermenter so you can pitch your yeast as soon as possible. Made from passivated 304 stainless steel, The Beast has a 30 ft. wort line with 1.5" T.C. connections and a 29.5 ft. coolant line with 1/2" male BSPT connections. Tri-clamp connections offer the most sanitary way to pass wort through your heat exchanger and pairs perfectly with BrewBuilt's line of T.C. Kettles and X1 Uni Conical Fermenters. The BSP coolant connections work well with Camlock, Duotight, NPT or other BSP fittings found below. Adding a ball valve to the coolant line inlet is a great way to dial in flow for maximum cooling efficiency!
When it comes to counterflow chillers, we love the coil design for its ease-of-use. Plate chillers are great for their high efficiency and compact size, but if there's too much hop matter running through them, they can quickly clog up. Transferring wort from your kettle to your fermenter is one of the critical steps in the brewing process where you don't want any hiccups. The Beast's wort line is 1/2" ID so it can withstand high amounts of hop additions without clogging!
A cross bar is welded on one side of the coil with pre-drilled mounting holes allowing it to be easily installed under your work bench or mounted directly to your brewing system.
Specs:
Beer Line: 30 ft. long
Beer Connection: 1.5" tri-clamp
Coolant Line: 29.5 ft. long
Coolant Connection: 1/2" BSPT
Crossbar with pre-drilled mounting holes (4mm)
Made from 304 stainless steel
BrewBuilt Bi-Metal Thermometers are top-of-the-line measuring instruments, made in the USA by Tel-Tru manufacturing. Maintain the overall precision of your brew system with these incredibly accurate and generally superior thermometers. These are produced according to strict standards, comparable to ISO9000 quality, and are set up with an 8 year manufacturers warranty boasting that quality.
Bi-metal thermometers are the level of quality you want when a few degree difference results in a completely different malt profile on your beer. While a bit more expensive, you won't ever mess up a batch because of incorrect temperature readings. The 2.5" Stem is a perfect balance of being long enough to get accurate readings, while not protruding far enough to get hit by a wandering mash paddle or spoon.
Are all bi-metal thermometers created equal? Not really. The problem with most bi-metal thermometers is that hang ups occur and you have to tap the thermometer to get an accurate reading. The cause of the problem is that the bimetallic helical coil in the stem of other bi-metal thermometers is tack welded to the stem itself. Our new line of thermometers feature a super sensitive bimetallic helical coil suspended from a copper coated bushing fixed in the stem.
This superior design provides a faster response to temperature changes and assures more accurate readings. What does this mean? You don't have to tap the gauge with your finger as much.
They are also accurate to 1% of the total range, feature a polished 3" 304 s/s housing, a hermetically sealed water proof case, glass face, external calibration capabilities, and a unique anti-parallax dial that provides for easy reading. The reading is actually taken from the last 2.5" of the probe.
Features:
Large 3" Dial Face for easy readings
2.5" Stem perfect for Boil Kettles and HLTs
High Grade Stainless Steel Construction and hermetically sealed casing
Can be calibrated with 1/16" Allen Wrench (Though should never be needed)
Dual Scale Range: 0-220° F, -10 to 100° C
Back Connection is 1/2" MPT, stem is 1/4" SS
8 year Manufacturer Warranty
BrewBuilt Bi-Metal Thermometers are top-of-the-line measuring instruments, made in the USA by Tel-Tru manufacturing. Maintain the overall precision of your brew system with these incredibly accurate and generally superior thermometers. These are produced according to strict standards, comparable to ISO9000 quality, and are set up with an 8 year manufacturers warranty boasting that quality.
Bi-metal thermometers are the level of quality you want when a few degree difference results in a completely different malt profile on your beer. While a bit more expensive, you won't ever mess up a batch because of incorrect temperature readings. The 6" Stem here is perfect for Mash Tuns, as it will reach further into the mash to get a more representative reading.
Are all bi-metal thermometers created equal? Not really. The problem with most bi-metal thermometers is that hang ups occur and you have to tap the thermometer to get an accurate reading. The cause of the problem is that the bimetallic helical coil in the stem of other bi-metal thermometers is tack welded to the stem itself. Our new line of thermometers feature a super sensitive bimetallic helical coil suspended from a copper coated bushing fixed in the stem.
This superior design provides a faster response to temperature changes and assures more accurate readings. What does this mean? You don't have to tap the gauge with your finger as much.
They are also accurate to 1% of the total range, feature a polished 3" 304 s/s housing, a hermetically sealed water proof case, glass face, external calibration capabilities, and a unique anti-parallax dial that provides for easy reading. The reading is actually taken from the last 2.5" of the probe.
Features:
Large 3" Dial Face for easy readings
6" Stem perfect for Boil Kettles and HLTs
High Grade Stainless Steel Construction and hermetically sealed casing
Can be calibrated with 1/16" Allen Wrench (Though should never be needed)
Dual Scale Range: 0-220° F, -10 to 100° C
Back Connection is 1/2" MPT, stem is 1/4" SS
8 year Manufacturer Warranty
This unique thermowell fitting is has the probe offset from the center of the fitting, leaving room for additional hardware such as the BrewBuilt Whirlpool Return Fitting. Pairing the two fittings allows you to recirculate wort in your boil kettle while still getting temperature readings from your thermometer or temperature probe. The thermowell has a 6" probe that fits all BrewBuilt kettles so that you can get the most accurate temperature measurement of your wort.
Kettle Maximizer allows you to pull liquor or wort from below the depth of your kettle's bottom port
Angle straight down in hot liquor tanks to maximize pick up
Rotate to your preferred pick-up height in boil kettles to leave trub behind when transferring to fermenter
The tri-clamp maximizer is recommended for boil kettles and hot liquor tanks with 1.5" T.C. bottom ports. This fitting will allow you to pull liquor or wort from below the depth of your kettle's bottom port without the need to tip your vessel. For hot liquor tanks, point the end of the tube straight down to maximize pick up. For boil kettles, you can rotate the maximizer to position the end of the tube at your preferred height above the bottom of the kettle, leaving room for a layer of trub that will be left behind in the kettle when you transfer wort to your fermenter.
1.5" tri-clamp
Tube Length: 6.5"
Overall Length: 8.18"
Made from stainless steel
The BrewBuilt T.C. spunding valve will give you the highest level of accuracy when fermenting under pressure. Designed for use with the BrewBuilt X-Series Uni Conical Fermenter, the spunding valve attaches to the lid's 1.5" tri-clamp port where the blow off fitting is normally installed. It can also be used with any pressurizable stainless steel conical with 1.5" T.C. top ports. The polycarbonate cylinder that surrounds the spunding valve can be filled with water or sanitizer to keep your tank 100% sanitary throughout the fermentation process.
Adjustable from 0.3–14.5 psi, designed for the X3
Made from 304 stainless steel
11.75" H x 4" Ø
For Your Safety: Never exceed the maximum rated working pressure of your vessel at any time during operation. The fixed-pressure PRV on your conical should always remain in place while using this spunding valve.
Made specifically for whirlpooling, this fitting angles ricrculating wort along the kettle wall for a more efficient whirlpool effect
Doubles as a kettle maximizer, allowing you to pull wort from below the depth of your kettle's bottom port
Rotate to your preferred pick-up height in the kettle to leave trub behind when transferring to fermenter
Compatible with kettles 12" in diameter and larger
This unique tri-clamp fitting works perfectly for whirlpooling hops at the end of the boil and doubles as kettle maximizer when transferring out to your fermenter. When recirculating wort through the bottom port, wort will be returned to flow along the kettle wall for a more efficient whirlpool effect, drawing vegetal matter into the center of your kettle. When transferring wort out, the fitting will then pull from the side of the kettle where matter has been cleared, and by angling the end of the tube downwards, you'll be able to pull liquid from below the depth of your kettle's bottom port without the need to tip your vessel.
1.5" tri-clamp
Length from T.C. to tube bend: 7" (approx.)
Length from tube bend to outlet: 9" (approx.)
Made from stainless steel
Recirculate wort in your boil kettle without sacrificing one of your tri-clamp ports. The BrewBuilt Whirlpool Return Fitting & Thermowell Offset kit allows you to use any tri-clamp kettle's thermometer port to recirculate wort while also taking temp readings. This kit is perfect for kettles that only have two tri-clamp ports—eliminating the need to drill out a hole in your kettle to add a third port for wort recirculation. Attach your preferred valve or tri-clamp fitting to the side inlet and, during whirlpool, draw wort from your bottom port and pump it back through the Whirlpool Return Fitting.
Kit Includes:
Whirlpool Return Fitting
Thermowell Offset
(1) 1.5" Tri-Clamp
(1) 1.5" Tri-Clamp Gasket (EPDM)
The BrewBuilt Whirlpool Return Fitting allows you to recirculate wort in your boil kettle without sacrificing one of your tri-clamp ports. Install it in any tri-clamp kettle's thermometer port and attach your preferred valve to the side inlet. The front of the fitting can be capped off with a 1.5" T.C. end cap, or you can pair with the BrewBuilt Thermowell Offset to install a thermometer or temperature probe.
Go mobile with this heavy-duty caster set for the BrewBuilt X-Series Uni Conical. Your fermenter moves around the brewery a lot, so why not give it some glide? Roll from sanitizing to kettle transfer to keg transfer to cleaning with minimal effort. Moving a stainless conical around can be taxing, give your back a break and upgrade your X-Series Conical with a set of rolling casters.
Simply remove the thread-in adjustable feet from your conical and replace them with the casters. The set includes two locking and two non-locking wheels. In general, we recommend putting the pair of locking wheels at the front of the conical.
Add dry hops without introducing oxygen to your fermenting or finished beer!
Load hops into the Hop Bong, fill it with CO2 via the ball lock cap, and pull the PRV to release oxygen
This is the perfect accessory to protect your finished beer from oxygen ingress when it's still in the fermenter
6 oz capacity per "hop drop"—easily repeat the process if you just gotta have More!
Compatible with all BrewBuilt X-Series fermenters and any stainless conical with 1.5" T.C. top port
The Hop Bong is a versatile pressurizable tri-clamp accessory that is perfect for purging oxygen from your dry hops before dropping them into your fermenter. Load up the Hop Bong, flush it with CO2, purge out oxygen with the handy PRV on top, then simply open the Butterfly Valve to inject your beer with a 6 oz payload of dry hops.
This kit is specifically adapted for use with the BrewBuilt X-Series conical fermenters and can be used with any stainless fermenter with 1.5" tri-clamp top port. The 2" T.C. Hop Bong attaches to a stainless 2" butterfly valve that then connects to a 2" x 1.5" T.C. reducer. This allows the largest capacity Hop Bong to be used with any of the 1.5" T.C. accessory ports on the BrewBuilt Conical's lid.
Hop Pellet Capacity: 150–180g (5.2–6.3 oz)
Kit Includes:
2" Hop Bong
Stainless Ball Lock Cap
Red PRV & PCO1881 Cap Combo
2" BrewBuilt Butterfly Valve
2" x 1.5" Tri-Clamp Reducer
(3) 2" Tri-Clamps
(3) 2" T.C. Gaskets
Warning: Always depressurize your system COMPLETELY before removing fittings from your fermenter.
The BrewBuilt X2 Conical Lid comes with one 4" T.C. port and two 1.5" T.C. ports. This is a direct replacement to the lid that comes standard on the X2 Uni, but X1 Uni owners can also upgrade to this lid if they want to take advantage of the second 1.5" port. This extra port is great for adding hops or other flavor additions without needing to remove and reinstall the Blowoff U Barb or other accessories attached to the primary 1.5" port. Also features a pull ring PRV built into the lid.
The 25/38 gal size will fit X1 28/42 gal fermenters.
NOTE: The lid does not include clamps, gaskets, or other fittings seen in the example photo. The PRV will come pre-installed and all other ports will come bare.
No Need to Upgrade Later, The X3 Comes Fully Loaded:
Built-in external cooling jacket with 1.5" TC Ports
Neoprene jacket for insulation
Pressure Pack lid with floating dip tube, draft style QD connections for sampling/serving, and an extra 1.5" TC for hop bongs.
The Clear Flex Chamber Bottom Dump allows you to see fermentation, collect and remove trub, and has added ports for purging, oxygenating, carbing and more... so flexible.
Highest quality mirror polish finish inside and out
Welded, ground and polished interior welds are the very highest quality and the ultimate for sanitation
New Features:
Professional 8” Tri-Clamp lid replaces the need for a complicated band clamp to attach the lid
Four crossbar reinforced legs, that flare out, create the most stable base and more access to the front fittings and dump system
Horizontal ports on the cone, just like pro tanks, allowing your racking arm, carbstone, and thermometer to have a horizontal placement in your tank. This allows for smaller minimum batch sizes, better carbonation, and more
3" oversized bottom port and Butterfly Valve with 3” tri-clamp Flex Chamber collection vessel
The new X3 from BrewBuilt sets the new standard for quality. We guarantee that you will love the fit and finish of the X3 Uni Jacketed Conical. Made entirely of 304 stainless steel, with flawless welds and a dazzling mirror-polish finish inside and out that is simply the best. The BrewBuilt X3 Uni is easy to sanitize and even easier on the eyes. It is definitely Instagram worthy! #BrewBuilt
External Cooling Jacket
When it comes to temperature control for a homebrew conical fermenter the holy grail has been an external cooling jacket. Internal cooling coils have long been the answer and while they are simpler to make and relatively inexpensive, they are harder to clean and have issues cold crashing in warm environments. The BrewBuilt X3 Jacketed Conical offers maximum cooling power without any compromise of sanitation.
8” Tri-Clamp Top Port
New to the X3, the 8” Tri-Clamp lid is rock solid and easy to use. The 8” opening allows plenty of space to still get in and clean the inside of the conical by hand if desired. A unique 8”, three-piece, tri-clamp is used to make sealing the top very easy and very secure.
Extra Large 3” T.C. Dump Valve
The largest in the industry. Dry hop to your heart's desire. Try as they might, hopheads will have a hard time clogging this conical. With an oversized 3" bottom port, you’ll have all the clearance you need (and even more than some pro brewers) to drop out your dry hop additions with ease. The slick mirror-polish finish on the inside allows flocculating yeast to collect neatly at the bottom of the cone as they slide right down the smooth interior walls. The butterfly dump valve integrates perfectly with the optional Flex Chamber Collection Jar and Yeast Harvester.
Reinforced Four-Leg Foundation
There’s a common complaint about the tippiness of three-legged units. Three legs may be fine when the fermenter is sitting still on an even surface, but users are often forced to purchase a bracing shelf for more stability if they add casters or leg extensions. A conical is only as worthy as its foundation, so BrewBuilt modeled the X3 after professional-level brewery tanks with a four-leg, reinforced base. This seemingly small design feature is more expensive to produce, but it's what makes the X3 conical exceedingly stable when compared to other models. When you fill up your fermenter with delicious fresh wort, you want to trust the vessel that’s holding your latest creation. Brewers shouted from the mountaintops that they wanted stronger, sturdier legs right out of the box that doesn’t require an additional bracing shelf. The four-leg, welded-bar reinforced system is absolutely rock solid. This is an especially critical feature if you plan to add rolling casters so you can easily glide the fermenter around your brewery.
The reinforced four-leg design not only increased the stability and strength of the conical but also allows the unit to stand taller, thereby eliminating the need for extensions in almost every situation. An elbow, a sight glass, or the Flex Chamber can be mounted under the unit with room to spare.
Adjustable Feet
The X3 Jacketed Conical comes standard with reinforced thread-in adjustable feet. If your home brewery has uneven flooring, you can quickly and easily level out the fermenter. The feet can be swapped out with high-quality casters at any time.
Flex Chamber Collection Jar - Trub Separator & Yeast Harvester
Working in collaboration with KegLand, we developed the pressurizable Flex Chamber Collection Jar. It attaches directly to the butterfly dump valve and can be used for removing trub, harvesting yeast, and many other tasks. Since it's made from crystal clear Triton, you'll be able to visually monitor fermentation activity just as you would with a sight glass. Ball lock adapters can be attached to the threaded ports on either side, allowing you to connect oxygenation or carbonation stones, or flush the Flex Chamber with CO2 and use it to inject hops or other ingredients into your conical. Also, a great option for storing yeast! Simply attach a 3" T.C. end cap or PRV and store your harvested yeast in the fridge for your next fermentation.
Pressure Pack with Clear Float Technology
Adding pressure capability will allow you to ferment, carbonate, and even serve all in one vessel. The Pressure Pack features the unique Clear Float Technology racking tube that can be used for taking samples, transferring to keg, or serving finished beer. This innovative feature draws beer from the top down, which means you’re always pulling the clearest, most sediment-free beer possible. Using pressure to draw a sample from the floating dip tube will also eliminate the tiny bit of oxygen that would be injected into your beer every time the traditional sample valve is opened.
Pressure transferring from fermenter to keg is the best way to protect your beer from oxygen when it’s at its most vulnerable state. Kegging could be considered the final hurdle in the brewing process, where limiting oxygen exposure is critical. This could mean the difference between your beer tasting great for months or tasting great for a week. Don’t take any chances. Use the Pressure Pack to keg from the top down and leave sediment behind.
Other Features You’ll Love:
Downward-facing Blowoff U Barb prevents blow off tubing from kinking and is much easier to remove and clean than a fixed stainless blow off
Stainless steel lid clamp with single-piece molded silicone gasket
In our GEN 3 redesign, we've added two more 1.5" T.C. ports to the cone and body for additional flexibility with current and upcoming product add-ons
X3 Accessories:
BrewBuilt Kit for Fermenting Under Pressure (Required to ferment or seal/cap an X3 with an active fermentation)
The Pressure Relief Valve (PRV) that comes with the conical is not sufficient for fermentation as it can become clogged with Krausen. To ferment or seal/cap an active fermentation requires the use and safety of the Pressure Fermentation Kit. This no-compromises kit includes the same hardware you will find on a commercial unitank, including a dedicated pro level spunding valve, a sealed pressure gauge, and a dedicated commercial PRV. Read more about these key hardware features in the kit copy. Also included is liquid Foam-Axe which helps reduce Krausen. Please read and follow all special instructions that come with the kit as well as your instruction manual.
Hop Bong Oxygen-Free Dry Hopping Device
The Hop Bong is a versatile pressurizable tri-clamp accessory that is perfect for purging oxygen from your dry hops before dropping them into your fermenter. Load up the Hop Bong, flush it with CO2, purge out oxygen with the handy PRV on top, then simply open the Butterfly Valve to inject your beer with a 6 oz payload of dry hops.
High Roller Caster Set
Go mobile with this heavy-duty caster set. Your fermenter moves around the brewery a lot, so why not give it some glide? Roll from sanitizing to kettle transfer to keg transfer to cleaning with minimal effort. Moving a stainless conical around can be taxing. Give your back a break and upgrade your conical with a set of rolling casters.
IceMaster Max 2
Built to pair perfectly with the IceMaster Max 2 glycol chiller. Easily and efficiently control your fermentation temperature and cold crash for conditioning and clarifying. Pair with our BrewBuilt Insulated Tubing Kit that comes complete with premium quick disconnects with shutoff valves that provide a “dry break” when they’re disconnected.
Immersion Heater
The X3's cone features a 2" tri-clamp port specifically for installing an Immersion Heater. The low watt density heating element gently warms your fermenting beer without scorching. A must-have for brewers living in colder climates or if you want the peace of mind that your temperature will never drop too low for your ale or kveik strains regardless of the time of year.
Full List of X3 Conical Features:
External Cooling Jacket with 1.5" Tri-Clamp connections
Pressure Pack with Clear Float, a floating dip tube that draws beer from the top down.
Flex Chamber Collection Jar, a clear, pressure capable bottom jar that allows you to see fermentation, remove trub, and connect additional accessories
Neoprene insulation sleeve
Wide base with 4 legs for stability
304 stainless steel construction
Mirror polish finish
Interior welds are the best in the business - uniquely ground and polished
(1) 2“ TC port for direct immersion heaters
(3) Horizontal welded cone ports
(1) 8" Lid Cap Opening with 8” TC Clamp
(5) 1.5" TC Lid Openings
3" TC bottom dump with 3" TC butterfly valve
1.5" Thermowell for inserting thermal probe
(4) Adjustable feet
Silicone tube for blow off
Stainless 8” Three Piece Tri Clamp & one piece molded gasket
Built-in 15 psi PRV (Not sufficient for fermentation - optional Pressure Fermentation Kit required for pressure fermentations)
For volume and dimensional specs, Download the PDF.
Installation Note: The Pressure Pack's Clear Float floating dip tube is sized to fit all models of the BrewBuilt Conical. Depending on the size of your fermenter, you may need to shorten the silicone tube for better performance. When installed on your empty fermenter, you ideally want the dip tube to hang freely with just enough length for the end of the dip tube to touch the bottom of the tank.
No Need to Upgrade Later, The X3 Comes Fully Loaded:
Built-in external cooling jacket with 1.5" TC Ports
Neoprene jacket for insulation
Pressure Pack lid with floating dip tube, draft style QD connections for sampling/serving, and an extra 1.5" TC for hop bongs.
The Clear Flex Chamber Bottom Dump allows you to see fermentation, collect and remove trub, and has added ports for purging, oxygenating, carbing and more... so flexible.
Highest quality mirror polish finish inside and out
Welded, ground and polished interior welds are the very highest quality and the ultimate for sanitation
New Features:
Professional 8” Tri-Clamp lid replaces the need for a complicated band clamp to attach the lid
Four crossbar reinforced legs, that flare out, create the most stable base and more access to the front fittings and dump system
Horizontal ports on the cone, just like pro tanks, allowing your racking arm, carbstone, and thermometer to have a horizontal placement in your tank. This allows for smaller minimum batch sizes, better carbonation, and more
3" oversized bottom port and Butterfly Valve with 3” tri-clamp Flex Chamber collection vessel
The new X3 from BrewBuilt sets the new standard for quality. We guarantee that you will love the fit and finish of the X3 Uni Jacketed Conical. Made entirely of 304 stainless steel, with flawless welds and a dazzling mirror-polish finish inside and out that is simply the best. The BrewBuilt X3 Uni is easy to sanitize and even easier on the eyes. It is definitely Instagram worthy! #BrewBuilt
External Cooling Jacket
When it comes to temperature control for a homebrew conical fermenter the holy grail has been an external cooling jacket. Internal cooling coils have long been the answer and while they are simpler to make and relatively inexpensive, they are harder to clean and have issues cold crashing in warm environments. The BrewBuilt X3 Jacketed Conical offers maximum cooling power without any compromise of sanitation.
8” Tri-Clamp Top Port
New to the X3, the 8” Tri-Clamp lid is rock solid and easy to use. The 8” opening allows plenty of space to still get in and clean the inside of the conical by hand if desired. A unique 8”, three-piece, tri-clamp is used to make sealing the top very easy and very secure.
Extra Large 3” T.C. Dump Valve
The largest in the industry. Dry hop to your heart's desire. Try as they might, hopheads will have a hard time clogging this conical. With an oversized 3" bottom port, you’ll have all the clearance you need (and even more than some pro brewers) to drop out your dry hop additions with ease. The slick mirror-polish finish on the inside allows flocculating yeast to collect neatly at the bottom of the cone as they slide right down the smooth interior walls. The butterfly dump valve integrates perfectly with the optional Flex Chamber Collection Jar and Yeast Harvester.
Reinforced Four-Leg Foundation
There’s a common complaint about the tippiness of three-legged units. Three legs may be fine when the fermenter is sitting still on an even surface, but users are often forced to purchase a bracing shelf for more stability if they add casters or leg extensions. A conical is only as worthy as its foundation, so BrewBuilt modeled the X3 after professional-level brewery tanks with a four-leg, reinforced base. This seemingly small design feature is more expensive to produce, but it's what makes the X3 conical exceedingly stable when compared to other models. When you fill up your fermenter with delicious fresh wort, you want to trust the vessel that’s holding your latest creation. Brewers shouted from the mountaintops that they wanted stronger, sturdier legs right out of the box that doesn’t require an additional bracing shelf. The four-leg, welded-bar reinforced system is absolutely rock solid. This is an especially critical feature if you plan to add rolling casters so you can easily glide the fermenter around your brewery.
The reinforced four-leg design not only increased the stability and strength of the conical but also allows the unit to stand taller, thereby eliminating the need for extensions in almost every situation. An elbow, a sight glass, or the Flex Chamber can be mounted under the unit with room to spare.
Adjustable Feet
The X3 Jacketed Conical comes standard with reinforced thread-in adjustable feet. If your home brewery has uneven flooring, you can quickly and easily level out the fermenter. The feet can be swapped out with high-quality casters at any time.
Flex Chamber Collection Jar - Trub Separator & Yeast Harvester
Working in collaboration with KegLand, we developed the pressurizable Flex Chamber Collection Jar. It attaches directly to the butterfly dump valve and can be used for removing trub, harvesting yeast, and many other tasks. Since it's made from crystal clear Triton, you'll be able to visually monitor fermentation activity just as you would with a sight glass. Ball lock adapters can be attached to the threaded ports on either side, allowing you to connect oxygenation or carbonation stones, or flush the Flex Chamber with CO2 and use it to inject hops or other ingredients into your conical. Also, a great option for storing yeast! Simply attach a 3" T.C. end cap or PRV and store your harvested yeast in the fridge for your next fermentation.
Pressure Pack with Clear Float Technology
Adding pressure capability will allow you to ferment, carbonate, and even serve all in one vessel. The Pressure Pack features the unique Clear Float Technology racking tube that can be used for taking samples, transferring to keg, or serving finished beer. This innovative feature draws beer from the top down, which means you’re always pulling the clearest, most sediment-free beer possible. Using pressure to draw a sample from the floating dip tube will also eliminate the tiny bit of oxygen that would be injected into your beer every time the traditional sample valve is opened.
Pressure transferring from fermenter to keg is the best way to protect your beer from oxygen when it’s at its most vulnerable state. Kegging could be considered the final hurdle in the brewing process, where limiting oxygen exposure is critical. This could mean the difference between your beer tasting great for months or tasting great for a week. Don’t take any chances. Use the Pressure Pack to keg from the top down and leave sediment behind.
Other Features You’ll Love:
Downward-facing Blowoff U Barb prevents blow off tubing from kinking and is much easier to remove and clean than a fixed stainless blow off
Stainless steel lid clamp with single-piece molded silicone gasket
In our GEN 3 redesign, we've added two more 1.5" T.C. ports to the cone and body for additional flexibility with current and upcoming product add-ons
X3 Accessories:
BrewBuilt Kit for Fermenting Under Pressure (Required to ferment or seal/cap an X3 with an active fermentation)
The Pressure Relief Valve (PRV) that comes with the conical is not sufficient for fermentation as it can become clogged with Krausen. To ferment or seal/cap an active fermentation requires the use and safety of the Pressure Fermentation Kit. This no-compromises kit includes the same hardware you will find on a commercial unitank, including a dedicated pro level spunding valve, a sealed pressure gauge, and a dedicated commercial PRV. Read more about these key hardware features in the kit copy. Also included is liquid Foam-Axe which helps reduce Krausen. Please read and follow all special instructions that come with the kit as well as your instruction manual.
Hop Bong Oxygen-Free Dry Hopping Device
The Hop Bong is a versatile pressurizable tri-clamp accessory that is perfect for purging oxygen from your dry hops before dropping them into your fermenter. Load up the Hop Bong, flush it with CO2, purge out oxygen with the handy PRV on top, then simply open the Butterfly Valve to inject your beer with a 6 oz payload of dry hops.
High Roller Caster Set
Go mobile with this heavy-duty caster set. Your fermenter moves around the brewery a lot, so why not give it some glide? Roll from sanitizing to kettle transfer to keg transfer to cleaning with minimal effort. Moving a stainless conical around can be taxing. Give your back a break and upgrade your conical with a set of rolling casters.
IceMaster Max 2
Built to pair perfectly with the IceMaster Max 2 glycol chiller. Easily and efficiently control your fermentation temperature and cold crash for conditioning and clarifying. Pair with our BrewBuilt Insulated Tubing Kit that comes complete with premium quick disconnects with shutoff valves that provide a “dry break” when they’re disconnected.
Immersion Heater
The X3's cone features a 2" tri-clamp port specifically for installing an Immersion Heater. The low watt density heating element gently warms your fermenting beer without scorching. A must-have for brewers living in colder climates or if you want the peace of mind that your temperature will never drop too low for your ale or kveik strains regardless of the time of year.
Full List of X3 Conical Features:
External Cooling Jacket with 1.5" Tri-Clamp connections
Pressure Pack with Clear Float, a floating dip tube that draws beer from the top down.
Flex Chamber Collection Jar, a clear, pressure capable bottom jar that allows you to see fermentation, remove trub, and connect additional accessories
Neoprene insulation sleeve
Wide base with 4 legs for stability
304 stainless steel construction
Mirror polish finish
Interior welds are the best in the business - uniquely ground and polished
(1) 2“ TC port for direct immersion heaters
(3) Horizontal welded cone ports
(1) 8" Lid Cap Opening with 8” TC Clamp
(5) 1.5" TC Lid Openings
3" TC bottom dump with 3" TC butterfly valve
1.5" Thermowell for inserting thermal probe
(4) Adjustable feet
Silicone tube for blow off
Stainless 8” Three Piece Tri Clamp & one piece molded gasket
Built-in 15 psi PRV (Not sufficient for fermentation - optional Pressure Fermentation Kit required for pressure fermentations)
For volume and dimensional specs, Download the PDF.
Installation Note: The Pressure Pack's Clear Float floating dip tube is sized to fit all models of the BrewBuilt Conical. Depending on the size of your fermenter, you may need to shorten the silicone tube for better performance. When installed on your empty fermenter, you ideally want the dip tube to hang freely with just enough length for the end of the dip tube to touch the bottom of the tank.
No Need to Upgrade Later, The X3 Comes Fully Loaded:
Built-in external cooling jacket with 1.5" TC Ports
Neoprene jacket for insulation
Pressure Pack lid with floating dip tube, draft style QD connections for sampling/serving, and an extra 1.5" TC for hop bongs.
The Clear Flex Chamber Bottom Dump allows you to see fermentation, collect and remove trub, and has added ports for purging, oxygenating, carbing and more... so flexible.
Highest quality mirror polish finish inside and out
Welded, ground and polished interior welds are the very highest quality and the ultimate for sanitation
New Features:
Professional 8” Tri-Clamp lid replaces the need for a complicated band clamp to attach the lid
Four crossbar reinforced legs, that flare out, create the most stable base and more access to the front fittings and dump system
Horizontal ports on the cone, just like pro tanks, allowing your racking arm, carbstone, and thermometer to have a horizontal placement in your tank. This allows for smaller minimum batch sizes, better carbonation, and more
3" oversized bottom port and Butterfly Valve with 3” tri-clamp Flex Chamber collection vessel
The new X3 from BrewBuilt sets the new standard for quality. We guarantee that you will love the fit and finish of the X3 Uni Jacketed Conical. Made entirely of 304 stainless steel, with flawless welds and a dazzling mirror-polish finish inside and out that is simply the best. The BrewBuilt X3 Uni is easy to sanitize and even easier on the eyes. It is definitely Instagram worthy! #BrewBuilt
External Cooling Jacket
When it comes to temperature control for a homebrew conical fermenter the holy grail has been an external cooling jacket. Internal cooling coils have long been the answer and while they are simpler to make and relatively inexpensive, they are harder to clean and have issues cold crashing in warm environments. The BrewBuilt X3 Jacketed Conical offers maximum cooling power without any compromise of sanitation.
8” Tri-Clamp Top Port
New to the X3, the 8” Tri-Clamp lid is rock solid and easy to use. The 8” opening allows plenty of space to still get in and clean the inside of the conical by hand if desired. A unique 8”, three-piece, tri-clamp is used to make sealing the top very easy and very secure.
Extra Large 3” T.C. Dump Valve
The largest in the industry. Dry hop to your heart's desire. Try as they might, hopheads will have a hard time clogging this conical. With an oversized 3" bottom port, you’ll have all the clearance you need (and even more than some pro brewers) to drop out your dry hop additions with ease. The slick mirror-polish finish on the inside allows flocculating yeast to collect neatly at the bottom of the cone as they slide right down the smooth interior walls. The butterfly dump valve integrates perfectly with the optional Flex Chamber Collection Jar and Yeast Harvester.
Reinforced Four-Leg Foundation
There’s a common complaint about the tippiness of three-legged units. Three legs may be fine when the fermenter is sitting still on an even surface, but users are often forced to purchase a bracing shelf for more stability if they add casters or leg extensions. A conical is only as worthy as its foundation, so BrewBuilt modeled the X3 after professional-level brewery tanks with a four-leg, reinforced base. This seemingly small design feature is more expensive to produce, but it's what makes the X3 conical exceedingly stable when compared to other models. When you fill up your fermenter with delicious fresh wort, you want to trust the vessel that’s holding your latest creation. Brewers shouted from the mountaintops that they wanted stronger, sturdier legs right out of the box that doesn’t require an additional bracing shelf. The four-leg, welded-bar reinforced system is absolutely rock solid. This is an especially critical feature if you plan to add rolling casters so you can easily glide the fermenter around your brewery.
The reinforced four-leg design not only increased the stability and strength of the conical but also allows the unit to stand taller, thereby eliminating the need for extensions in almost every situation. An elbow, a sight glass, or the Flex Chamber can be mounted under the unit with room to spare.
Adjustable Feet
The X3 Jacketed Conical comes standard with reinforced thread-in adjustable feet. If your home brewery has uneven flooring, you can quickly and easily level out the fermenter. The feet can be swapped out with high-quality casters at any time.
Flex Chamber Collection Jar - Trub Separator & Yeast Harvester
Working in collaboration with KegLand, we developed the pressurizable Flex Chamber Collection Jar. It attaches directly to the butterfly dump valve and can be used for removing trub, harvesting yeast, and many other tasks. Since it's made from crystal clear Triton, you'll be able to visually monitor fermentation activity just as you would with a sight glass. Ball lock adapters can be attached to the threaded ports on either side, allowing you to connect oxygenation or carbonation stones, or flush the Flex Chamber with CO2 and use it to inject hops or other ingredients into your conical. Also, a great option for storing yeast! Simply attach a 3" T.C. end cap or PRV and store your harvested yeast in the fridge for your next fermentation.
Pressure Pack with Clear Float Technology
Adding pressure capability will allow you to ferment, carbonate, and even serve all in one vessel. The Pressure Pack features the unique Clear Float Technology racking tube that can be used for taking samples, transferring to keg, or serving finished beer. This innovative feature draws beer from the top down, which means you’re always pulling the clearest, most sediment-free beer possible. Using pressure to draw a sample from the floating dip tube will also eliminate the tiny bit of oxygen that would be injected into your beer every time the traditional sample valve is opened.
Pressure transferring from fermenter to keg is the best way to protect your beer from oxygen when it’s at its most vulnerable state. Kegging could be considered the final hurdle in the brewing process, where limiting oxygen exposure is critical. This could mean the difference between your beer tasting great for months or tasting great for a week. Don’t take any chances. Use the Pressure Pack to keg from the top down and leave sediment behind.
Other Features You’ll Love:
Downward-facing Blowoff U Barb prevents blow off tubing from kinking and is much easier to remove and clean than a fixed stainless blow off
Stainless steel lid clamp with single-piece molded silicone gasket
In our GEN 3 redesign, we've added two more 1.5" T.C. ports to the cone and body for additional flexibility with current and upcoming product add-ons
X3 Accessories:
BrewBuilt Kit for Fermenting Under Pressure (Required to ferment or seal/cap an X3 with an active fermentation)
The Pressure Relief Valve (PRV) that comes with the conical is not sufficient for fermentation as it can become clogged with Krausen. To ferment or seal/cap an active fermentation requires the use and safety of the Pressure Fermentation Kit. This no-compromises kit includes the same hardware you will find on a commercial unitank, including a dedicated pro level spunding valve, a sealed pressure gauge, and a dedicated commercial PRV. Read more about these key hardware features in the kit copy. Also included is liquid Foam-Axe which helps reduce Krausen. Please read and follow all special instructions that come with the kit as well as your instruction manual.
Hop Bong Oxygen-Free Dry Hopping Device
The Hop Bong is a versatile pressurizable tri-clamp accessory that is perfect for purging oxygen from your dry hops before dropping them into your fermenter. Load up the Hop Bong, flush it with CO2, purge out oxygen with the handy PRV on top, then simply open the Butterfly Valve to inject your beer with a 6 oz payload of dry hops.
High Roller Caster Set
Go mobile with this heavy-duty caster set. Your fermenter moves around the brewery a lot, so why not give it some glide? Roll from sanitizing to kettle transfer to keg transfer to cleaning with minimal effort. Moving a stainless conical around can be taxing. Give your back a break and upgrade your conical with a set of rolling casters.
IceMaster Max 2
Built to pair perfectly with the IceMaster Max 2 glycol chiller. Easily and efficiently control your fermentation temperature and cold crash for conditioning and clarifying. Pair with our BrewBuilt Insulated Tubing Kit that comes complete with premium quick disconnects with shutoff valves that provide a “dry break” when they’re disconnected.
Immersion Heater
The X3's cone features a 2" tri-clamp port specifically for installing an Immersion Heater. The low watt density heating element gently warms your fermenting beer without scorching. A must-have for brewers living in colder climates or if you want the peace of mind that your temperature will never drop too low for your ale or kveik strains regardless of the time of year.
Full List of X3 Conical Features:
External Cooling Jacket with 1.5" Tri-Clamp connections
Pressure Pack with Clear Float, a floating dip tube that draws beer from the top down.
Flex Chamber Collection Jar, a clear, pressure capable bottom jar that allows you to see fermentation, remove trub, and connect additional accessories
Neoprene insulation sleeve
Wide base with 4 legs for stability
304 stainless steel construction
Mirror polish finish
Interior welds are the best in the business - uniquely ground and polished
(1) 2“ TC port for direct immersion heaters
(3) Horizontal welded cone ports
(1) 8" Lid Cap Opening with 8” TC Clamp
(5) 1.5" TC Lid Openings
3" TC bottom dump with 3" TC butterfly valve
1.5" Thermowell for inserting thermal probe
(4) Adjustable feet
Silicone tube for blow off
Stainless 8” Three Piece Tri Clamp & one piece molded gasket
Built-in 15 psi PRV (Not sufficient for fermentation - optional Pressure Fermentation Kit required for pressure fermentations)
For volume and dimensional specs, Download the PDF.
Installation Note: The Pressure Pack's Clear Float floating dip tube is sized to fit all models of the BrewBuilt Conical. Depending on the size of your fermenter, you may need to shorten the silicone tube for better performance. When installed on your empty fermenter, you ideally want the dip tube to hang freely with just enough length for the end of the dip tube to touch the bottom of the tank.
No Need to Upgrade Later, The X3 Comes Fully Loaded:
Built-in external cooling jacket with 1.5" TC Ports
Neoprene jacket for insulation
Pressure Pack lid with floating dip tube, draft style QD connections for sampling/serving, and an extra 1.5" TC for hop bongs.
The Clear Flex Chamber Bottom Dump allows you to see fermentation, collect and remove trub, and has added ports for purging, oxygenating, carbing and more... so flexible.
Highest quality mirror polish finish inside and out
Welded, ground and polished interior welds are the very highest quality and the ultimate for sanitation
New Features:
Professional 8” Tri-Clamp lid replaces the need for a complicated band clamp to attach the lid
Four crossbar reinforced legs, that flare out, create the most stable base and more access to the front fittings and dump system
Horizontal ports on the cone, just like pro tanks, allowing your racking arm, carbstone, and thermometer to have a horizontal placement in your tank. This allows for smaller minimum batch sizes, better carbonation, and more
3" oversized bottom port and Butterfly Valve with 3” tri-clamp Flex Chamber collection vessel
The new X3 from BrewBuilt sets the new standard for quality. We guarantee that you will love the fit and finish of the X3 Uni Jacketed Conical. Made entirely of 304 stainless steel, with flawless welds and a dazzling mirror-polish finish inside and out that is simply the best. The BrewBuilt X3 Uni is easy to sanitize and even easier on the eyes. It is definitely Instagram worthy! #BrewBuilt
External Cooling Jacket
When it comes to temperature control for a homebrew conical fermenter the holy grail has been an external cooling jacket. Internal cooling coils have long been the answer and while they are simpler to make and relatively inexpensive, they are harder to clean and have issues cold crashing in warm environments. The BrewBuilt X3 Jacketed Conical offers maximum cooling power without any compromise of sanitation.
8” Tri-Clamp Top Port
New to the X3, the 8” Tri-Clamp lid is rock solid and easy to use. The 8” opening allows plenty of space to still get in and clean the inside of the conical by hand if desired. A unique 8”, three-piece, tri-clamp is used to make sealing the top very easy and very secure.
Extra Large 3” T.C. Dump Valve
The largest in the industry. Dry hop to your heart's desire. Try as they might, hopheads will have a hard time clogging this conical. With an oversized 3" bottom port, you’ll have all the clearance you need (and even more than some pro brewers) to drop out your dry hop additions with ease. The slick mirror-polish finish on the inside allows flocculating yeast to collect neatly at the bottom of the cone as they slide right down the smooth interior walls. The butterfly dump valve integrates perfectly with the optional Flex Chamber Collection Jar and Yeast Harvester.
Reinforced Four-Leg Foundation
There’s a common complaint about the tippiness of three-legged units. Three legs may be fine when the fermenter is sitting still on an even surface, but users are often forced to purchase a bracing shelf for more stability if they add casters or leg extensions. A conical is only as worthy as its foundation, so BrewBuilt modeled the X3 after professional-level brewery tanks with a four-leg, reinforced base. This seemingly small design feature is more expensive to produce, but it's what makes the X3 conical exceedingly stable when compared to other models. When you fill up your fermenter with delicious fresh wort, you want to trust the vessel that’s holding your latest creation. Brewers shouted from the mountaintops that they wanted stronger, sturdier legs right out of the box that doesn’t require an additional bracing shelf. The four-leg, welded-bar reinforced system is absolutely rock solid. This is an especially critical feature if you plan to add rolling casters so you can easily glide the fermenter around your brewery.
The reinforced four-leg design not only increased the stability and strength of the conical but also allows the unit to stand taller, thereby eliminating the need for extensions in almost every situation. An elbow, a sight glass, or the Flex Chamber can be mounted under the unit with room to spare.
Adjustable Feet
The X3 Jacketed Conical comes standard with reinforced thread-in adjustable feet. If your home brewery has uneven flooring, you can quickly and easily level out the fermenter. The feet can be swapped out with high-quality casters at any time.
Flex Chamber Collection Jar - Trub Separator & Yeast Harvester
Working in collaboration with KegLand, we developed the pressurizable Flex Chamber Collection Jar. It attaches directly to the butterfly dump valve and can be used for removing trub, harvesting yeast, and many other tasks. Since it's made from crystal clear Triton, you'll be able to visually monitor fermentation activity just as you would with a sight glass. Ball lock adapters can be attached to the threaded ports on either side, allowing you to connect oxygenation or carbonation stones, or flush the Flex Chamber with CO2 and use it to inject hops or other ingredients into your conical. Also, a great option for storing yeast! Simply attach a 3" T.C. end cap or PRV and store your harvested yeast in the fridge for your next fermentation.
Pressure Pack with Clear Float Technology
Adding pressure capability will allow you to ferment, carbonate, and even serve all in one vessel. The Pressure Pack features the unique Clear Float Technology racking tube that can be used for taking samples, transferring to keg, or serving finished beer. This innovative feature draws beer from the top down, which means you’re always pulling the clearest, most sediment-free beer possible. Using pressure to draw a sample from the floating dip tube will also eliminate the tiny bit of oxygen that would be injected into your beer every time the traditional sample valve is opened.
Pressure transferring from fermenter to keg is the best way to protect your beer from oxygen when it’s at its most vulnerable state. Kegging could be considered the final hurdle in the brewing process, where limiting oxygen exposure is critical. This could mean the difference between your beer tasting great for months or tasting great for a week. Don’t take any chances. Use the Pressure Pack to keg from the top down and leave sediment behind.
Other Features You’ll Love:
Downward-facing Blowoff U Barb prevents blow off tubing from kinking and is much easier to remove and clean than a fixed stainless blow off
Stainless steel lid clamp with single-piece molded silicone gasket
In our GEN 3 redesign, we've added two more 1.5" T.C. ports to the cone and body for additional flexibility with current and upcoming product add-ons
X3 Accessories:
BrewBuilt Kit for Fermenting Under Pressure (Required to ferment or seal/cap an X3 with an active fermentation)
The Pressure Relief Valve (PRV) that comes with the conical is not sufficient for fermentation as it can become clogged with Krausen. To ferment or seal/cap an active fermentation requires the use and safety of the Pressure Fermentation Kit. This no-compromises kit includes the same hardware you will find on a commercial unitank, including a dedicated pro level spunding valve, a sealed pressure gauge, and a dedicated commercial PRV. Read more about these key hardware features in the kit copy. Also included is liquid Foam-Axe which helps reduce Krausen. Please read and follow all special instructions that come with the kit as well as your instruction manual.
Hop Bong Oxygen-Free Dry Hopping Device
The Hop Bong is a versatile pressurizable tri-clamp accessory that is perfect for purging oxygen from your dry hops before dropping them into your fermenter. Load up the Hop Bong, flush it with CO2, purge out oxygen with the handy PRV on top, then simply open the Butterfly Valve to inject your beer with a 6 oz payload of dry hops.
High Roller Caster Set
Go mobile with this heavy-duty caster set. Your fermenter moves around the brewery a lot, so why not give it some glide? Roll from sanitizing to kettle transfer to keg transfer to cleaning with minimal effort. Moving a stainless conical around can be taxing. Give your back a break and upgrade your conical with a set of rolling casters.
IceMaster Max 2
Built to pair perfectly with the IceMaster Max 2 glycol chiller. Easily and efficiently control your fermentation temperature and cold crash for conditioning and clarifying. Pair with our BrewBuilt Insulated Tubing Kit that comes complete with premium quick disconnects with shutoff valves that provide a “dry break” when they’re disconnected.
Immersion Heater
The X3's cone features a 2" tri-clamp port specifically for installing an Immersion Heater. The low watt density heating element gently warms your fermenting beer without scorching. A must-have for brewers living in colder climates or if you want the peace of mind that your temperature will never drop too low for your ale or kveik strains regardless of the time of year.
Full List of X3 Conical Features:
External Cooling Jacket with 1.5" Tri-Clamp connections
Pressure Pack with Clear Float, a floating dip tube that draws beer from the top down.
Flex Chamber Collection Jar, a clear, pressure capable bottom jar that allows you to see fermentation, remove trub, and connect additional accessories
Neoprene insulation sleeve
Wide base with 4 legs for stability
304 stainless steel construction
Mirror polish finish
Interior welds are the best in the business - uniquely ground and polished
(1) 2“ TC port for direct immersion heaters
(3) Horizontal welded cone ports
(1) 8" Lid Cap Opening with 8” TC Clamp
(5) 1.5" TC Lid Openings
3" TC bottom dump with 3" TC butterfly valve
1.5" Thermowell for inserting thermal probe
(4) Adjustable feet
Silicone tube for blow off
Stainless 8” Three Piece Tri Clamp & one piece molded gasket
Built-in 15 psi PRV (Not sufficient for fermentation - optional Pressure Fermentation Kit required for pressure fermentations)
For volume and dimensional specs, Download the PDF.
Installation Note: The Pressure Pack's Clear Float floating dip tube is sized to fit all models of the BrewBuilt Conical. Depending on the size of your fermenter, you may need to shorten the silicone tube for better performance. When installed on your empty fermenter, you ideally want the dip tube to hang freely with just enough length for the end of the dip tube to touch the bottom of the tank.
The X3 Jacketed Conical and IceMaster Max 2 work hand in glove from yeast pitching to cold crashing
External cooling jacket with neoprene insulation allows for unparalleled temperature control for a homebrew fermenter
Max 2 glycol chiller with digital controllers and built-in submersible pumps provides quiet and efficient chilling
Insulated tubing sets eliminate line sweating and feature dry break quick disconnects at the cooling jacket connection points
The BrewBuilt Ultimate Chilling package includes everything you'll need to maintain a precise level of temperature control throughout the fermentation process. The X3 Jacketed Conical is second-to-none in homebrew-level cooling capabilities—mirroring the fermenter design that professional brewers have long relied on to keep their temperatures in check. And what better unit to provide the cooling solution than the IceMaster Max 2? This low-profile glycol chiller provides all the cooling capacity you'll need and is so compact that it only takes up about 12" of extra space next to your conical.
X3 Jacketed Uni Conical & IceMaster Max 2
The X3 Jacketed Uni Conical offers cutting edge design features that have long been reserved for pro-level fermentation tanks. Circulating cooling solution through an external cooling jacket offers superior cooling power when compared to internal cooling coils, and eliminates the need for cleaning a wonky apparatus after you've transferred out your finished beer. This pressurizable fermenter also sports a neoprene jacket for added insulation, Flex Chamber collection container for yeast harvesting or trub dumps, internal floating racking tube for clear beer transfers, and so much more! The IceMaster Max 2 makes for the perfect tag team partner, providing all the cooling capacity you'll need for small-volume batches. And with two built-in submersible pumps with independent controllers, you can always add a sidekick fermenter and control both batches simultaneously.
BrewBuilt Insulated Glycol Tubing Kit
In addition to the conical and chiller, the kit also includes an insulated tubing set that improves chilling efficiency and eliminates line sweating. The kit consists of:
1 - Insulated Tubing Set (2 x 6' lines)
2 - High Temp Plastic Female QDs w/ 3/8" Barb*
2 - High Temp Plastic Male QDs w/ 1/2" MPT*
2 - 1.5" Tri-Clamps
2 - 1.5" T.C. Gaskets
2 - 1.5" T.C. x 1/2" FPT Adapters
*These premium quick disconnects feature shutoff valves that provide a "dry break" when they're disconnected. That means no cooling solution leaking all over your brewery every time you take the system apart for cleaning. The Female QDs are installed on the insulated tubing, and the Male QDs are installed on the T.C. x FPT Adapters that connect to the cooling jacket's inlet and outlet.
Due to high demand, some of these items are currently out of stock but available for pre-order. Please check status notes below when selecting a size option to see if it is In Stock or tagged as PreBook. We will automatically ship this to you when we receive more inventory.
The X3 Jacketed Conical and IceMaster Max 4 work hand in glove from yeast pitching to cold crashing
External cooling jacket with neoprene insulation allows for unparalleled temperature control for a homebrew fermenter
Max 4 glycol chiller with digital controllers and built-in submersible pumps provides quiet and efficient chilling
With room to connect up to 4 conicals, this package is perfect for brewers planning to expand their fermentation capacity over time
Insulated tubing sets eliminate line sweating and feature dry break quick disconnects at the cooling jacket connection points
The BrewBuilt Ultimate Chilling package includes everything you'll need to maintain a precise level of temperature control throughout the fermentation process. The X3 Jacketed Conical is second-to-none in homebrew-level cooling capabilities—mirroring the fermenter design that professional brewers have long relied on to keep their temperatures in check. And what better unit to provide the cooling solution than the IceMaster Max 4? This powerful glycol chiller has more than enough cooling capacity for your chosen X3 Conical with room to add an additional three fermenters down the road.
X3 Jacketed Uni Conical & IceMaster Max 4
The X3 Jacketed Uni Conical offers cutting edge design features that have long been reserved for pro-level fermentation tanks. Circulating cooling solution through an external cooling jacket offers superior cooling power when compared to internal cooling coils, and eliminates the need for cleaning a wonky apparatus after you've transferred out your finished beer. This pressurizable fermenter also sports a neoprene jacket for added insulation, Flex Chamber collection container for yeast harvesting or trub dumps, internal floating racking tube for clear beer transfers, and so much more! The IceMaster Max 4 makes for the perfect tag team partner, providing all the cooling capacity you'll need for up to four fermenters.
BrewBuilt Insulated Glycol Tubing Kit
In addition to the conical and chiller, the kit also includes an insulated tubing set that improves chilling efficiency and eliminates line sweating. The kit consists of:
1 - Insulated Tubing Set (2 x 6' lines)
2 - High Temp Plastic Female QDs w/ 3/8" Barb*
2 - High Temp Plastic Male QDs w/ 1/2" MPT*
2 - 1.5" Tri-Clamps
2 - 1.5" T.C. Gaskets
2 - 1.5" T.C. x 1/2" FPT Adapters
*These premium quick disconnects feature shutoff valves that provide a "dry break" when they're disconnected. That means no cooling solution leaking all over your brewery every time you take the system apart for cleaning. The Female QDs are installed on the insulated tubing, and the Male QDs are installed on the T.C. x FPT Adapters that connect to the cooling jacket's inlet and outlet.
The X3 Jacketed Conical and IceMaster Max 2 work hand in glove from yeast pitching to cold crashing
External cooling jacket with neoprene insulation allows for unparalleled temperature control for a homebrew fermenter
Max 2 glycol chiller with digital controllers and built-in submersible pumps provides quiet and efficient chilling
Insulated tubing sets eliminate line sweating and feature dry break quick disconnects at the cooling jacket connection points
High-quality, stainless steel table with rolling casters saves space in your brewery and can be easily moved whenever needed
The BrewBuilt Ultimate Chilling package includes everything you'll need to maintain a precise level of temperature control throughout the fermentation process. The X3 Jacketed Conical is second-to-none in homebrew-level cooling capabilities—mirroring the fermenter design that professional brewers have long relied on to keep their temperatures in check. And what better unit to provide the cooling solution than the IceMaster Max 2? This low-profile glycol chiller provides all the cooling capacity you'll need and is compact enough to ride shotgun on the included stainless steel work table.
X3 Jacketed Uni Conical & IceMaster Max 2
The X3 Jacketed Uni Conical offers cutting edge design features that have long been reserved for pro-level fermentation tanks. Circulating cooling solution through an external cooling jacket offers superior cooling power when compared to internal cooling coils, and eliminates the need for cleaning a wonky apparatus after you've transferred out your finished beer. This pressurizable fermenter also sports a neoprene jacket for added insulation, Flex Chamber collection container for yeast harvesting or trub dumps, internal floating racking tube for clear beer transfers, and so much more! The IceMaster Max 2 makes for the perfect tag team partner, providing all the cooling capacity you'll need for small-volume batches. And with two built-in submersible pumps with independent controllers, you can always add a sidekick fermenter and control both batches simultaneously.
BrewBuilt Insulated Glycol Tubing Kit
In addition to the conical and chiller, the kit also includes an insulated tubing set that improves chilling efficiency and eliminates line sweating. The kit consists of:
1 - Insulated Tubing Set (2 x 6' lines)
2 - High Temp Plastic Female QDs w/ 3/8" Barb*
2 - High Temp Plastic Male QDs w/ 1/2" MPT*
2 - 1.5" Tri-Clamps
2 - 1.5" T.C. Gaskets
2 - 1.5" T.C. x 1/2" FPT Adapters
*These premium quick disconnects feature shutoff valves that provide a "dry break" when they're disconnected. That means no cooling solution leaking all over your brewery every time you take the system apart for cleaning. The Female QDs are installed on the insulated tubing, and the Male QDs are installed on the T.C. x FPT Adapters that connect to the cooling jacket's inlet and outlet.
Stainless Steel Work Table
The heavy-duty stainless steel work table is the final piece that makes this the Ultimate Chilling Package. Saddle up the X3 Conical and IceMaster Chiller to reduce the footprint of your brewery. And with the swivel rolling casters installed, you'll have easy mobility to move your setup if ever needed.
Please Note: Avoid moving the table while the Conical is resting on top or in use. This can lead to injury or damage to the conical and surrounding area. The table cannot accommodate the 25 or 38 gal X3 conicals.
Replacement clamp for the BrewBuilt X3 Uni Conical 8" tri-clamp lid. This 3-piece stainless steel tri-clamp features two hinges which makes the clamp easier to work with on larger fitting sizes.
Special tri-clamp gasket made for the X3 conical series. Compatible with all sizes of X3 via 8" tri-clamp connection.
Not compatible with X2 or X1 Uni Conicals.
The ultimate control & precision of your fermentation process. Equipped with two built-in temperature controllers and pumps, this advanced chiller enables you to independently regulate the temperature of two separate fermentation vessels simultaneously, ensuring optimal conditions for different batches or styles of beer, making it a game-changer for homebrewers.
2 built-in submersible pumps with independent digital controllers
Control multiple fermentation temperatures independently
Fill with 20% glycol solution for optimal chilling performance
Cold crash with good insulation
Perfect complement to BrewBuilt X-Series Conicals
The IceMaster Max 2 is designed to cool fermentations in small vessels. It features 2 built-in submersible pumps with independent digital temperature controllers and can be used with any vessel that has a glycol jacket or submersed cooling coil/rod. Each controller includes a temperature probe that should be inserted into a thermowell in your vessel or can be taped to the outside of the vessel if you don't have a thermowell. The digital controller then measures the temperature of your tank and turns the submersible pump on or off to cool to your desired set temperature. Up to two tanks can be controlled separately with one IceMaster Max 2.
The Max 2 is the perfect unit for brewers with 1 or 2 fermentation vessels. The IceMaster 100 and IceMaster Max 4 are terrific chillers, but for they have far more cooling capacity than the average homebrewer needs. The Max 2 is the most affordable glycol chiller we offer, and thanks to the built-in submersible pumps and controllers, there's no need to purchase additional pump kits to use with your cooling system(s).
Compatibility
The IceMaster can be used with any fermenter that has a built-in cooling jacket, added CoolStix, or a submersed cooling coil. It works well as the cooling source for the following systems and fermenters.
BrewBuilt Jacketed Uni Conical - we recommend one Insulated Tubing Kit for each tank. These kits feature "dry break" quick disconnects that prevent glycol loss and the insulated tubing will increase chilling efficiency and eliminate line sweating from condensation.
CoolStix - CoolStix can be added to a wide range of carboys, fermenters, and tanks and the IceMaster works really well in combination. Each CoolStix is available with or without a pump kit; for use with the IceMaster Max 2 you will only need the CoolStix and some tubing to connect it to the chiller.
Ss Brewtech Fermenters and Brites - Ss BME Chronicals, BME Brites, and Unitanks come with cooling coils and neoprene as standard. The optional chilling FTSs will not be needed for use with the Max 2.
Spike Conical with Optional Cooling Coil - the cooling coil for Spike CF series conicals is available for purchase independently from the TC-100 cooling system. For use with the Max 2 you will only need the coil and some tubing to connect it to the chiller.
Speidel Tanks with Optional Cooling Jackets - You will need two lengths of tubing to connect the chiller to each tank.
Grainfather Fermenters - Grainfather fermenters have standard cooling jackets. You will need two lengths of tubing for each fermenter.
Blichmann Fermenators with Optional Cooling Coil - You will need two lengths of tubing for each Fermenator.
Capacity
It is always difficult to determine exactly how many tanks can be chilled at one time as it depends on what is happening in each tank, if the tank is insulated, and what the ambient temperature is. Cold crashing always requires the most energy and requires tank insulation. We have experimented with capacities and can provide this general guide based on a 75°F ambient and neoprene insulation. Neoprene provides a modest amount of insulation so you would obtain better results using Armaflex or a higher R rated insulation.
At 75°F ambient temperature with neoprene insulation, the Max 2 can cold crash one 1 BBL BrewBuilt Jacketed Uni or two Jacketed Unis up to 15 gallons in size at one time to 38°F.
Set Up
In order to hook up the IceMaster to your fermenter or tank's cooling system, you will need 2 lengths of tubing per vessel. All tubing connections should be secured with hose clamps. The unit comes with JoinTech Male Quick Disconnects installed as the inlet/outlet bulkheads, and also includes Female QDs with barbs to connect your tubing to the bulkheads. QDs to connect tubing to your cooling system are not included as the connection type depends on your setup.
Length 1: 1st bulkhead (IN) to cooling system outlet
Length 2: 2nd bulkhead (OUT) to cooling system inlet
Specifications:
2 built-in submersible pumps with independent digital controllers
Pump controller reads in °F / °C
Temperature controller reads in °C
Labeled IN and OUT bulkheads with Male QD JoinTech Dry Break Quick Disconnects
(4) Female QD JoinTech Dry Break Quick Disconnect w/ 1/2" Barb included
Tank Capacity: 17 L / 4.5 Gal. Water Capacity
Compressor: 3/8 HP
Cooling Capacity: 500 Watt/1700btu/0.14 tons
Refrigerant: R600a
Voltage: 110V
Dimensions: 19" x 12" x 17.5"
Wheels not included
CE Certified
Note: The sight glass attaches to the front of the unit by threading the elbow fitting to the bottom threaded drain port, and attaching the other end to the upper mount. Note that the top of the sight glass is open to allow overflow to drain out if the reservoir is overfilled.
Warning: Do not set the reservoir temperature controller lower than 28°F (-2ºC). Running the unit below this temperature may negatively affect the unit's efficiency and has the potential to freeze beer which may impact the finished beer's flavor.
The ultimate control & precision of your fermentation process. Equipped with two built-in temperature controllers and pumps, this advanced chiller enables you to independently regulate the temperature of two separate fermentation vessels simultaneously, ensuring optimal conditions for different batches or styles of beer, making it a game-changer for homebrewers.
2 built-in submersible pumps with independent digital controllers
Control multiple fermentation temperatures independently
Fill with 20% glycol solution for optimal chilling performance
Cold crash with good insulation
Perfect complement to BrewBuilt X-Series Conicals
The IceMaster Max 2 is designed to cool fermentations in small vessels. It features 2 built-in submersible pumps with independent digital temperature controllers and can be used with any vessel that has a glycol jacket or submersed cooling coil/rod. Each controller includes a temperature probe that should be inserted into a thermowell in your vessel or can be taped to the outside of the vessel if you don't have a thermowell. The digital controller then measures the temperature of your tank and turns the submersible pump on or off to cool to your desired set temperature. Up to two tanks can be controlled separately with one IceMaster Max 2.
The Max 2 is the perfect unit for brewers with 1 or 2 fermentation vessels. The IceMaster 100 and IceMaster Max 4 are terrific chillers, but for they have far more cooling capacity than the average homebrewer needs. The Max 2 is the most affordable glycol chiller we offer, and thanks to the built-in submersible pumps and controllers, there's no need to purchase additional pump kits to use with your cooling system(s).
Compatibility
The IceMaster can be used with any fermenter that has a built-in cooling jacket, added CoolStix, or a submersed cooling coil. It works well as the cooling source for the following systems and fermenters.
BrewBuilt Jacketed Uni Conical - we recommend one Insulated Tubing Kit for each tank. These kits feature "dry break" quick disconnects that prevent glycol loss and the insulated tubing will increase chilling efficiency and eliminate line sweating from condensation.
CoolStix - CoolStix can be added to a wide range of carboys, fermenters, and tanks and the IceMaster works really well in combination. Each CoolStix is available with or without a pump kit; for use with the IceMaster Max 2 you will only need the CoolStix and some tubing to connect it to the chiller.
Ss Brewtech Fermenters and Brites - Ss BME Chronicals, BME Brites, and Unitanks come with cooling coils and neoprene as standard. The optional chilling FTSs will not be needed for use with the Max 2.
Spike Conical with Optional Cooling Coil - the cooling coil for Spike CF series conicals is available for purchase independently from the TC-100 cooling system. For use with the Max 2 you will only need the coil and some tubing to connect it to the chiller.
Speidel Tanks with Optional Cooling Jackets - You will need two lengths of tubing to connect the chiller to each tank.
Grainfather Fermenters - Grainfather fermenters have standard cooling jackets. You will need two lengths of tubing for each fermenter.
Blichmann Fermenators with Optional Cooling Coil - You will need two lengths of tubing for each Fermenator.
Capacity
It is always difficult to determine exactly how many tanks can be chilled at one time as it depends on what is happening in each tank, if the tank is insulated, and what the ambient temperature is. Cold crashing always requires the most energy and requires tank insulation. We have experimented with capacities and can provide this general guide based on a 75°F ambient and neoprene insulation. Neoprene provides a modest amount of insulation so you would obtain better results using Armaflex or a higher R rated insulation.
At 75°F ambient temperature with neoprene insulation, the Max 2 can cold crash one 1 BBL BrewBuilt Jacketed Uni or two Jacketed Unis up to 15 gallons in size at one time to 38°F.
Set Up
In order to hook up the IceMaster to your fermenter or tank's cooling system, you will need 2 lengths of tubing per vessel. All tubing connections should be secured with hose clamps. The unit comes with JoinTech Male Quick Disconnects installed as the inlet/outlet bulkheads, and also includes Female QDs with barbs to connect your tubing to the bulkheads. QDs to connect tubing to your cooling system are not included as the connection type depends on your setup.
Length 1: 1st bulkhead (IN) to cooling system outlet
Length 2: 2nd bulkhead (OUT) to cooling system inlet
Specifications:
2 built-in submersible pumps with independent digital controllers
Pump controller reads in °F / °C
Temperature controller reads in °C
Labeled IN and OUT bulkheads with Male QD JoinTech Dry Break Quick Disconnects
(4) Female QD JoinTech Dry Break Quick Disconnect w/ 1/2" Barb included
Tank Capacity: 17 L / 4.5 Gal. Water Capacity
Compressor: 3/8 HP
Cooling Capacity: 500 Watt/1700btu/0.14 tons
Refrigerant: R600a
Voltage: 110V
Dimensions: 19" x 12" x 17.5"
Wheels not included
CE Certified
Note: The sight glass attaches to the front of the unit by threading the elbow fitting to the bottom threaded drain port, and attaching the other end to the upper mount. Note that the top of the sight glass is open to allow overflow to drain out if the reservoir is overfilled.
Warning: Do not set the reservoir temperature controller lower than 28°F (-2ºC). Running the unit below this temperature may negatively affect the unit's efficiency and has the potential to freeze beer which may impact the finished beer's flavor.
