Get Your Kegging Setup Under Pressure

• 

  Duotight Ball Lock QD Gas In | Quick Disconnect Gas In Push-In Fitting

  1 review

  The humble plastic ball lock disconnect has been around a long time and is used by countless homebrewers around the world. Despite the extensive use they have seen little to no innovation for decades and KegLand wanted to change this. Enter the Duotight Ball Lock QD. The integrated Duotight design means you can connect your beer and gas line directly, easily and reliably with no need for additional fittings or clamps. It is a robust and super compact design that is incredibly easy to assemble and disassemble, making cleaning and sanitizing an absolute breeze! Made from highly chemical resistant materials with stainless springs and ball bearings (no cheap ABS plastics here) this baby is extremely resistant to commonly used chemicals such as phosphoric based sanitizers and caustics. The incredibly small form factor allows for easy stacking of kegs. The new cap design ensures a pressure seal with just hand tightening and it can be completely taken apart for cleaning with no tools required. Duotight Ball Lock QDs are offered in three sizes that correspond to the outer diameters seen on our line of EVABarrier Draft Tubing. 6.35 mm OD – features a very tight 3 mm ID that requires only 3.2 ft of length for adequate flow resistance. This is the ideal size for mobile draft or if you want to keep your kegerator as tidy as possible. 8 mm OD – the most common OD size of EVABarrier tubing. This size comes in two IDs (4 mm & 5 mm) and pairs up with the lion's share of Duotight fittings and accessories. 4 mm ID is our most recommended size for beverage lines, requiring 5-6 ft. lengths. 5 mm ID is commonly used as gas line or when 10-12 ft. beverage lines are required. 9.5 mm OD – suitable for gas lines or long draw beverage lines. At 6.3 mm ID, this size is ideal for beverage lines that will be 20 ft. or longer in length. Duotight Push-to-Connect These Duotight ball lock disconnects already have the Duotight fitting built into the ball lock disconnect. No need for additional threaded fittings. Simply push the beer/gas line in and you are done! Compact The world's most compact ball lock disconnect ever manufactured. This new compact form factor is great for tight spaces or fridges where you want to pack as many kegs in as possible. This is one of the only ball lock disconnects that allows standard ball lock kegs to be double stacked while still connected to beer and gas lines. Overmolded Poppet The overmolded poppet design means you can couple and disconnect this ball lock QD under extreme pressures of up to 150 psi (higher than most kegs working pressure) and will never have issues with the o-ring blowing out. Tool-less Disassembly Other ball lock disconnects require a tool such as a flat head screw driver or spanner to take them apart for cleaning. The new caps on these allow for easy disassembly by hand, making these easier to break down for cleaning. It's literally never been easier to remove hop particles from your ball lock disconnects. Extreme Chemical Resistance No cheap ABS plastic or nitrile seals. This ball lock disconnect is made from stainless spring and ball bearings, with an engineering polyketone resin body, EPDM and PP/EPDM overmolded poppet. This makes the quick disconnect resistant to extreme chemicals such as phosphoric and acetic acid, caustic soda, peroxide and many other acid or base chemicals which are commonly used in homebrewing. Toughness This ball lock disconnect is more robust than any other plastic ball lock disconnect ever manufactured due to the use of new engineering plastics. Don't be fooled by the small form factor — these bad boys are tough! High Flow The internal design of these allows for faster flow meaning you can slightly quicker transfers when compared to other plastic ball lock disconnects. Features: Ball Lock Quick Disconnect - Gas In Direct connect EVABarrier tubing Compact design won't interfere with keg stacking Made from highly chemical resistant materials Disassemble by hand for quick and easy cleaning Three sizes available: 6.35 mm (KL24242) 8 mm (KL20756) 9.5 mm (KL20770)

  Read more less

  $8.79

• 

  Duotight Ball Lock QD Beverage Out | Quick Disconnect Bev Out Push-In Fitting

  2 reviews

  The humble plastic ball lock disconnect has been around a long time and is used by countless homebrewers around the world. Despite the extensive use they have seen little to no innovation for decades and KegLand wanted to change this. Enter the Duotight Ball Lock QD. The integrated Duotight design means you can connect your beer and gas line directly, easily and reliably with no need for additional fittings or clamps. It is a robust and super compact design that is incredibly easy to assemble and disassemble, making cleaning and sanitizing an absolute breeze! Made from highly chemical resistant materials with stainless springs and ball bearings (no cheap ABS plastics here) this baby is extremely resistant to commonly used chemicals such as phosphoric based sanitizers and caustics. The incredibly small form factor allows for easy stacking of kegs. The new cap design ensures a pressure seal with just hand tightening and it can be completely taken apart for cleaning with no tools required. Duotight Ball Lock QDs are offered in three sizes that correspond to the outer diameters seen on our line of EVABarrier Draft Tubing. 6.35 mm OD – features a very tight 3 mm ID that requires only 3.2 ft of length for adequate flow resistance. This is the ideal size for mobile draft or if you want to keep your kegerator as tidy as possible. 8 mm OD – the most common OD size of EVABarrier tubing. This size comes in two IDs (4 mm & 5 mm) and pairs up with the lion's share of Duotight fittings and accessories. 4 mm ID is our most recommended size for beverage lines, requiring 5-6 ft. lengths. 5 mm ID is commonly used as gas line or when 10-12 ft. beverage lines are required. 9.5 mm OD – suitable for gas lines or long draw beverage lines. At 6.3 mm ID, this size is ideal for beverage lines that will be 20 ft. or longer in length. Duotight Push-to-Connect These Duotight ball lock disconnects already have the Duotight fitting built into the ball lock disconnect. No need for additional threaded fittings. Simply push the beer/gas line in and you are done! Compact The world's most compact ball lock disconnect ever manufactured. This new compact form factor is great for tight spaces or fridges where you want to pack as many kegs in as possible. This is one of the only ball lock disconnects that allows standard ball lock kegs to be double stacked while still connected to beer and gas lines. Overmolded Poppet The overmolded poppet design means you can couple and disconnect this ball lock QD under extreme pressures of up to 150 psi (higher than most kegs working pressure) and will never have issues with the o-ring blowing out. Tool-less Disassembly Other ball lock disconnects require a tool such as a flat head screw driver or spanner to take them apart for cleaning. The new caps on these allow for easy disassembly by hand, making these easier to break down for cleaning. It's literally never been easier to remove hop particles from your ball lock disconnects. Extreme Chemical Resistance No cheap ABS plastic or nitrile seals. This ball lock disconnect is made from stainless spring and ball bearings, with an engineering polyketone resin body, EPDM and PP/EPDM overmolded poppet. This makes the quick disconnect resistant to extreme chemicals such as phosphoric and acetic acid, caustic soda, peroxide and many other acid or base chemicals which are commonly used in homebrewing. Toughness This ball lock disconnect is more robust than any other plastic ball lock disconnect ever manufactured due to the use of new engineering plastics. Don't be fooled by the small form factor — these bad boys are tough! High Flow The internal design of these allows for faster flow meaning you can slightly quicker transfers when compared to other plastic ball lock disconnects. Features: Ball Lock Quick Disconnect - Bev Out Direct connect EVABarrier tubing Compact design won't interfere with keg stacking Made from highly chemical resistant materials Dissamble by hand for quick and easy cleaning Three sizes available: 6.35 mm (KL24235) 8 mm (KL20749) 9.5 mm (KL20763)

  Read more less

  $8.79

• 

  Blichmann | QuickCarb™ | Keg Carbonator | co2-injection system

  70 reviews

  Quickly carbonate your beer using the same process most large commercial breweries use! Beer is carbonated and ready to drink in less than an hour Easy to clean and sanitize No one likes waiting, and the QuickCarb keg carbonator by Blichmann Engineering is the way to eliminate the wait from carbonating your homebrew.  This high-pressure co2-injection system from Blichmann Engineering™ will carbonate a keg in 30 minutes, with no chance of over carbonating your beer.  All connectors are included, and the unit hangs from the front of your keg. Use is simple,  just sanitize the unit using the built in pump, and connect hoses to your Keg and CO2 system.  Turn on the gas, plug in the unit, and 30-40 minutes later, your beer will be perfectly carbonated.  Cleanup is just as easy, as you can run cleaner and sanitizer through the system using the pump as well.

  Read more less

  $218.99

• 

  KegLand Oxebar Mono PET Keg | Ball Lock Adapter Tapping Head

  8 reviews

  PCO38 threaded tapping head pairs perfectly with Oxebar Mono PET Kegs for a lightweight, affordable draft dispensing system Dip tube features a filter attachment to keep solids in the keg and out of your glass Includes liquid and gas ball lock posts and pull-ring PRV rated to 36 psi Now includes PCO38 Gen2 black elbow cap insert This handy PCO38 Tapping Head assembly is a great way to get into kegging. Using standard homebrew ball lock disconnects, this is a convenient, light weight, robust and inexpensive solution to kegging beer, cocktails, kombucha, wine, and other beverages. This PCO38 tapping head assembly has been designed to suit standard PCO38 bottle necks such as the 4L or 8L Oxebar Mono PET Keg. KegLand utilizes quality engineering plastics and efficient injection stretch blow mould processes to manufacture economical kegs and tapping heads for both homebrewing and commercial beers. The plastics used in the tapping head can withstand a wide range of chemicals used in the brewing industry and relatively high temperatures (212°F / 100°C). The Ball Lock Tapping Head kit comes with 2.5 BAR (36 psi) PRV, liquid and gas ball lock posts, and dip tube with filter attachment. KegLand Part Number: KL2714   NOTE: The Oxebar Mono Keg shown in the example photos is sold separately.

  Read more less

  $21.99

• 

  Slimline Torpedo Keg | Ball Lock Keg | Stainless Steel Corny Keg | Low2 Keg Lid O-Ring | Superior Oxygen Barrier Properties

  2 reviews

  The Slimline Torpedo Keg series features a smaller diameter to maximize the space in your kegerator or keezer Low2 lid O-ring reduces oxygen ingress by 96% compared to silicone O-rings when measured in a keg! Brand new, all-stainless construction ball lock keg Stackable with ball lock quick disconnects in place Etched In and Out labels near the keg posts for easy identification Rolled handles for a comfortable grip Made by an ISO certified commercial keg manufacturer with high-quality laser welded seams Torpedo Kegs too wide? Want to squeeze another keg in your kegerator? The patented design, D794,899, of the Slimline Torpedo Keg is 9% more slim than the classic model with all the same great features. Coming in at about 1/4" thinner than standard Ball Lock Cornelius Kegs, this keg has welded stainless handles and the ability to stack kegs with fittings still in place all at a great price. Quality First Here at MoreBeer! we love nothing more than quality interior welds. We've spent a decade rejecting kegs made overseas because the interior welds have never met our standards. If a weld is not perfect and shows evident burn marks along with nooks and crannies it cannot be sanitized effectively. Torpedo kegs are machine welded and exceed our standards for quality. This weld quality is possible because these kegs are made by an ISO certified commercial keg manufacturer. Cool Features Torpedo Kegs were designed to stack with Ball Lock quick disconnects in place and serving which is a cool feature for some brewers who have vertical space in their refrigerator. We also like the rolled stainless steel handles. They are comfortable to grab and will never come off like some rubber handles can over time. “In” and “Out” is etched near the keg posts for easy identification which is very handy when you are connecting lines in a refrigerator or kegerator and trying not to make a mistake. Low2 Keg Lid O-ring Give your beverage the absolute best protection from oxygen staling with the Low2 keg lid O-ring. Even the most perfectly sealed keg is susceptible to oxygen ingress through the hatch O-ring—yes, even if the keg is under constant pressure with CO2! Even a leak-free, pressurized keg will release CO2 molecules as they pass through the lid O-ring itself, and conversely, Oxygen molecules will permeate through the O-ring and diffuse into the keg when they reach the surface area on the other side. The level of permeability is wide ranging and highly dependent on what material the O-ring is made from. Rather than the usual EPDM or Silicone, Low2 gaskets are made from a unique composition of Synthetic M-Class and Cross-Link Elastomers. This special blend has superior oxygen barrier properties that results in your beverage staying fresher for longer. Taking your keg on the go? Don't leave home without a custom tailored Slimline Torpedo Keg Sleeve! Specifications: Max Pressure: 130 psi PRV Rating: 85 psi High Quality Laser Welded Seams ISO9001 Quality Assurance Made from 304 Stainless Steel Dimensions:   Height (in.) Diameter (in.) 1.5 Gal 11 8 3/8 2.5 Gal 15 5/8 8 3/8 5 Gal 25 1/2 8 3/8   For a slightly shorter keg, see our Standard Torpedo Kegs!  

  Read more less

  $119.99 - $149.99

• 

  KegLand Oxebar Mono PET Keg | Ball Lock Keg | Floating Dip Tube | 5.2 Gallons | 20L

  9 reviews

  Getting into kegging has never been more affordable! Grab this 5-gallon ball lock keg for less than half the cost of a stainless corny keg of the same size! Transparent Oxebar Mono plastic makes it easy to see how much beer you have left in the keg. Especially handy when dispensing on the go Floating dip tube comes standard—a huge upgrade over traditional ball lock kegs. Draw the clearest beer inside the keg while leaving sediment behind Oxebar Mono Kegs are made from Nylon impregnated PET and Polyketone (POK) fittings for superior oxygen barrier properties compared to standard PET plastic Wedge seals on the Tapping Head and Ball Lock Caps eliminate points of oxygen ingress found where rubber is traditionally used Lower total oxygen pickup compared to a standard corny keg with silicone lid seal This 5-gallon keg is lightweight, compact and has high oxygen barrier properties with 3x better (meaning less) gas transmission than traditional PET grades of plastic making it suitable for beer storage or other oxygen sensitive carbonated and non-carbonated beverages. The included Ball Lock Tapping Head comes complete with Red & Yellow Ball Lock Caps for gas and beverage, floating dip tube with filter screen, and pull-ring PRV. Molded handles make it easy to remove the tapping head for cleaning and also allow you to stack the kegs on top of each other, even with your ball lock quick disconnects in place. Being made from the Mono Barrier PET Polymer Matrix, rather than stainless steel, this keg is lightweight and an ideal choice for draft dispensing on the go. But with all the key features of a standard corny homebrew keg, plus the added feature of the floating dip tube, the Oxebar Mono Keg makes for an affordable keg option for home dispensing as well. Fit up to 3 of these bad boys in a KOMOS Standard or Deluxe Kegerator, or fit up to 6 in the KOMOS Double-Wide Kegerator. Includes: 20L Amber Mono Barrier PET Oxebar Keg Dual PCO1881 Lid Assembly with Oxebar Black Handles Green Pull Ring PRV (65 PSI) Silicone Floating Dip Tube w/ Filter Attachment Red & Yellow Ball Lock Quick Disconnect (QD) Caps Specs: Height: 25.1" Diameter: 9.2" Volume: 5.28 Gallons Fit up to 3 kegs in the KOMOS Standard & Deluxe Kegerators NOTE: Oxebar Mono kegs are marked with a manufacture date. 2 years after production, and every 2 years after first use, it is recommended that the keg be hydro tested to ensure the keg is holding pressure. Hydro test instructions are below. You will also need a 100 PSI Gray PRV to perform the test. Fill the keg to the brim with room temperature water Replace the Green PRV with a Gray PRV rated to 6 BAR or higher Pressurize the tank to 6 BAR (87 psi) Hold the keg at 6 BAR for 1 minute Release the pressure and immediately remove the Gray PRV and swap back to the Green PRV If leaks or potential points of failure are found, replace the tank KegLand Part Number: KL36054 NOTE: Oxebar kegs are marked with a manufacturer’s “expiry date”. This does not indicate that the keg is bad after this date; it simply indicates that a hydro test may be in order. 2 years after production and every 2 years after first use, it is recommended that the keg be hydro tested to ensure the tank is holding pressure. Hydro test instructions are available here. You will also need the KG520 Tapping Head and D1072 Green PRV to perform the test. If you do not plan to pressurize the keg, the test is not necessary.

  Read more less

  $49.99

• 

  KegLand Ball Lock Quick Disconnect (QD) | Beverage Out | Barbed

  45 reviews

  The most affordable ball lock quick disconnect we offer! Black color easily identifies the QD for beverage use 1/4" barb connection This black, beverage out quick disconnect comes with a barb for attaching to a beverage line, and its high quality construction creates a sturdy seal that won’t leak gas or beer when in use. The barb measures 1/4 inch, so 3/16 inch beverage tubing is recommend for the perfect fit.  Note: Sometiems ball lock fittings can be difficult to get fully seated on a Cornelius keg. We recommend using a quick spray of sanitizer solution to act as a lubricant and giving it a few twists while applying the ball lock. Kegland Part Number: KL02950

  Read more less

  $6.59

• 

  Torpedo Keg | Ball Lock Keg | Stainless Steel Corny Keg | Low2 Keg Lid O-Ring | Superior Oxygen Barrier Properties

  2 reviews

  Brand new, all-stainless construction ball lock keg Low2 lid O-ring reduces oxygen ingress by 96% compared to silicone O-rings when measured in a keg! Stackable with ball lock quick disconnects in place Etched In and Out labels near the keg posts for easy identification Rolled handles for a comfortable grip Made by an ISO certified commercial keg manufacturer with high-quality laser welded seams Set your sights on a brand new Torpedo Keg! The patented, D794,899, sleek all-stainless design represents the pinnacle of quality in ball lock homebrew kegs. With features like welded stainless handles, the ability to stack with fittings in place, amazing quality and a great price we think these kegs will become the standard by which other kegs are measured. Quality First The first thing we at MoreBeer! check out is interior welds. We've spent a decade rejecting kegs made overseas because the interior welds have never met our standards. If a weld is not perfect and shows evident burn marks along with nooks and crannies it cannot be sanitized effectively. These kegs are machine welded and exceed our standards for quality. The weld quality is possible because these kegs made by an ISO certified commercial keg manufacturer. Cool Features Torpedo Kegs were designed to stack with Ball Lock quick disconnects in place and serving which is a cool feature for some brewers who have vertical space in their refrigerator. We also like the rolled stainless steel handles. They are comfortable to grab and will never come off like some rubber handles can over time. In and Out is etched near the keg posts for easy identification which is very handy when you are connecting lines in a refrigerator or kegerator and trying not to make a mistake. Low2 Keg Lid O-ring Give your beverage the absolute best protection from oxygen staling with the Low2 keg lid O-ring. Even the most perfectly sealed keg is susceptible to oxygen ingress through the hatch O-ring—yes, even if the keg is under constant pressure with CO2! Even a leak-free, pressurized keg will release CO2 molecules as they pass through the lid O-ring itself, and conversely, Oxygen molecules will permeate through the O-ring and diffuse into the keg when they reach the surface area on the other side. The level of permeability is wide ranging and highly dependent on what material the O-ring is made from. Rather than the usual EPDM or Silicone, Low2 gaskets are made from a unique composition of Synthetic M-Class and Cross-Link Elastomers. This special blend has superior oxygen barrier properties that results in your beverage staying fresher for longer. Taking your keg on the go? Don't leave home without a custom fitted Torpedo Keg Sleeve! Specifications: Max Pressure: 130 psi PRV Rating: 85 psi High Quality Laser Welded Seams ISO9001 Quality Assurance Made from 304 Stainless Steel Dimensions:   Height (in.) Diameter (in.) 1.5 Gal 10.25 9 2.5 Gal 14.75 9 5 Gal 23 9 Please Note: These are about 1/2" wider than standard Ball Lock Cornelius Kegs. Need something a bit slimmer? Check out our lineup of Slimline Torpedo Kegs!  

  Read more less

  $119.99 - $149.99

• 

  CMBecker Ball Lock Quick Disconnect (QD) | Beverage Out | Flared | High-Quality Plastic QD | NSF Registered | Made in Germany | Assembled in USA

  35 reviews

  The highest quality plastic ball lock quick disconnect available to homebrewers Smooth operation—clicks into place on keg posts and is easily removed Built-in flare washer—no need for a separate nylon washer that is required with stainless steel QDs CMBecker is an international manufacturer of beverage dispensing solutions for both home and professional draft equipment Black plastic clearly identifies the disconnect as the liquid out QD This black, beverage out quick disconnect comes with a flare for attaching to a beverage line, and it's made by CM Becker so you know it is high quality. The flare threads measure 1/4 inch. Note: Sometimes ball lock fittings can be difficult to get fully seated on a Cornelius keg. We recommend using a quick spray of sanitizer solution to act as a lubricant and giving it a few twists while applying the ball lock.  

  Read more less

  $7.29

• 

  CMBecker Ball Lock Quick Disconnect (QD) | Gas In | Flared | High-Quality Plastic QD | NSF Registered | Made in Germany | Assembled in USA

  26 reviews

  The highest quality plastic ball lock quick disconnect available to homebrewers Smooth operation—clicks into place on keg posts and is easily removed Built-in flare washer—no need for a separate nylon washer that is required with stainless steel QDs CMBecker is an international manufacturer of beverage dispensing solutions for both home and professional draft equipment Gray plastic clearly identifies the disconnect as the gas in QD This white, beverage out quick disconnect comes with a barb for attaching to a gas line, and it's made by CM Becker so you know it is high quality. 1/4" flare connection.   Note: Sometiems ball lock fittings can be difficult to get fully seated on a Cornelius keg. We recommend using a quick spray of sanitizer solution to act as a lubricant and giving it a few twists while applying the ball lock.

  Read more less

  $7.29

• 

  KegLand Ball Lock Quick Disconnect (QD) | Gas In | Barbed

  41 reviews

  The most affordable ball lock quick disconnect we offer! White color easily identifies the QD for gas use 1/4" barb connection This white, gas-in quick disconnect comes with a barb for attaching to a beverage line, and its high quality construction creates a sturdy seal that won’t leak gas when in use. The barb measures 1/4 inch, so it is compatible with either 1/4 inch or 5/16 inch beverage tubing.  Note: Sometiems ball lock fittings can be difficult to get fully seated on a Cornelius keg. We recommend using a quick spray of sanitizer solution to act as a lubricant and giving it a few twists while applying the ball lock. Kegland Part Number: KL02943

  Read more less

  $6.59

• 

  Duotight Flow Control Ball Lock Quick Disconnect (QD) | Beverage Out | Adjustable Flow Rate | 8 mm Duotight

  10 reviews

  If you want an easy way to balance your beer lines, this is the way to do it. One of the benefits of Flow Control disconnects is you don't need to rely on the small ID or line length to apply flow resistance. Rather than adjusting your line length or size, simply apply additional restriction directly on the Quick Disconnect (QD). This is perfect for people who want to serve a large range of beverages with differing carbonation levels without having to customize each line. Now with the added benefit of Duotight fittings built in. Please be aware that even in the fully open position these FC disconnects do have some inherent flow resistance so you should use either shorter line or larger ID line that you would when compared with traditional ball lock disconnects.   Flow Control QD vs. Flow Control Faucet One of the only drawbacks of flow control devices is that they inherently create a small amount of turbulence and therefore can cause foaming. In the past, flow control faucets have been the only common option. Flow control faucets are very popular but due to the fact that they are placed at the very end of the beer line they have no head pressure. As a result, any turbulence created can cause foaming and carbonation to come out of solution. Flow control ball lock disconnects like these on the other hand have the ability to restrict the flow before the beer enters the beer line so the head pressure created by the beer line keeps the carbonation in solution. Even in the instance that high turbulence is created the beer will be far more resistant to foaming issues. For this reason, flow control ball lock disconnects like these have significantly better performance allowing you the flexibility to adjust line resistance easily but without the introduction of turbulence that creates foaming. It cannot fix over-carbonated beer, but it can reduce the amount of beer line you would need to pour without excessive foaming. Duotight Ball Lock QDs The humble plastic ball lock disconnect has been around a long time and is used by countless homebrewers around the world.  Despite the extensive use they have seen little to no innovation for decades and KegLand wanted to change this. Enter the Duotight Ball Lock QD. The integrated Duotight design means you can connect your beer and gas line directly, easily and reliably with no need for additional fittings or clamps. It is a robust and super compact design that is incredibly easy to assemble and disassemble, making cleaning and sanitizing an absolute breeze! Made from highly chemical resistant materials with stainless springs and ball bearings (no cheap ABS plastics here) this baby is extremely resistant to commonly used chemicals such as phosphoric based sanitizers and caustics. The incredibly small form factor allows for easy stacking of kegs. The new cap design ensures a pressure seal with just hand tightening and it can be completely taken apart for cleaning with no tools required. Duotight Push-to-Connect These Duotight ball lock disconnects already have the Duotight fitting built into the ball lock disconnect. No need for additional threaded fittings. Simply push the beer/gas line in and you are done! Compact The world's most compact ball lock disconnect ever manufactured. This new compact form factor is great for tight spaces or fridges where you want to pack as many kegs in as possible. This is one of the only ball lock disconnects that allows standard ball lock kegs to be double stacked while still connected to beer and gas lines. Overmolded Poppet The overmolded poppet design means you can couple and disconnect this ball lock QD under extreme pressures of up to 150 psi (higher than most kegs working pressure) and will never have issues with the o-ring blowing out. Tool-less Disassembly Other ball lock disconnects require a tool such as a flat head screw driver or spanner to take them apart for cleaning. The new caps on these allow for easy disassembly by hand, making these easier to break down for cleaning. It's literally never been easier to remove hop particles from your ball lock disconnects. Extreme Chemical Resistance No cheap ABS plastic or nitrile seals. This ball lock disconnect is made from stainless spring and ball bearings, with an engineering polyketone resin body, EPDM and PP/EPDM overmolded poppet. This makes the quick disconnect resistant to extreme chemicals such as phosphoric and acetic acid, caustic soda, peroxide and many other acid or base chemicals which are commonly used in homebrewing. Toughness This ball lock disconnect is more robust than any other plastic ball lock disconnect ever manufactured due to the use of new engineering plastics. Don't be fooled by the small form factor — these bad boys are tough! Features: Ball Lock Quick Disconnect - Bev Out Adjustable flow rate Direct connect 8 mm EVABarrier tubing Compact design won't interfere with keg stacking Made from highly chemical resistant materials Dissamble by hand for quick and easy cleaning KegLand Part Number: KL21418

  Read more less

  $16.49

• 

  Rebuild Kit | O-Rings | Corny Keg

  31 reviews

  Keep your cherished Corny Kegs in perfect working order with this set of gaskets and o-rings. Having a spare set on hand is usually all you need to get your keg up and running on a moment's notice.   Kit includes two gaskets for the dip tubes, two for the body connects and one lid o-ring. Be sure to replace the gaskets on any used keg you acquire. A corny keg that has been used for soda in the past should have its gaskets replaced because the soda flavor can never be removed from the rubber.   This kit works for Ball Lock and most Pin Lock corny kegs.

  Read more less

  $4.39

• 

  Kegland CO2 Cartridge - 74 g

  These cartridges give the oomph to your mini-regulator dispensing unit! Perfect for dispensing your beer on the go. One canister will push between 1-4 Cornelius kegs, depending on how it is used and the CO2 consumption required. With the 74g adapter piece, these cartridges can be used with the KegLand Core 360 Mini Regulator or Torpedo Mini CO2 Regulator. 5/8-18 UNF threading Kegland Part Number: KL16889 Please note: due to air shipping restrictions, this product is only eligible for ground shipment within the contiguous United States.

  Read more less

  $12.99

• 

  Flash Brewing® Kegging Kit

  2 reviews

  Due to high demand, some of these items are currently out of stock but available for pre-order. Please check status notes below when selecting a size option to see if it is In Stock or tagged as PreBook. We will automatically ship this to you when we receive more inventory. Compact, all-in-one design for cost-effective, space-saving kegging. Leak-proof Duotight fittings for fast, tool-free assembly. EVABarrier tubing preserves flavor with superior oxidation resistance. Portable and fridge-friendly—easily tap beverages from any cooler or refrigerator. Discover the simplest and most cost-effective solution for kegging and dispensing your home-crafted beverages, ranging from beer and cider to cold brew coffee and draft cocktails. Designed to eliminate the need for expensive, bulky equipment, this all-in-one system provides a convenient pouring experience with a compact, space-saving footprint. The kit utilizes advanced components, including oxidation-resistant EVABarrier tubing and tool-free Duotight fittings, ensuring your setup is leak-proof and capable of preserving superior flavor stability. Whether you are looking to tap a drink directly from your kitchen refrigerator or need a portable option for a cooler, this complete package offers the most accessible path to enjoying draft quality at home. The 1-gallon kit option comes with two 1-gallon kegs and two tapping heads. We recommend this setup if you are using a standard kitchen fridge or want a portable system for a cooler. Since these kegs stand roughly 13" tall with the tapping head installed, they easily fit into tight spaces where height is an issue. Complete Kit Includes: Oxebar Keg Options: Choice 5-Gallon, 2-Gallon, or 2x 1-Gallon kegs Duotight Mini Regulator Duotight Handheld Beer Faucet Duotight Push-In Fittings Duotight Check Valve EVABarrier Gas and Beverage Tubing Easy Setup Instructions Flexible CO₂ Options Use single-use 16 g or 74 g CO₂ cartridges (not included); 74 g cartridges are recommended for best performance. Push-Fit Convenience Duotight fittings ensure quick, tool-free assembly with no clamps or Teflon tape required. Incredibly Cost-Effective The lowest-cost path into kegging and serving your own beverages, with professional-style pouring and carbonation using compact CO₂ cartridges. Ultra-Clean, Oxidation-Free Lines EVABarrier double-wall tubing is kink-resistant, oxygen-blocking, and PVC/BPA-free—perfectly matched to Duotight fittings. Why Choose Flash Kegging? Fast, clean, and compact setup. No CO₂ tank rentals or refills—just cartridges. Tap your drink straight from your fridge or picnic cooler. Keg Dimensions: 1-Gallon: 12.7" H x 6.1" D 2-Gallon: 20.5" H x 6.1" D 5-Gallon: 25.1" H x 9.2" D  

  Read more less

  $99.99 - $129.99

• 

  16g Threaded CO2 Cartridge | Pack of 6

  9 reviews

  16g threaded CO2 cartridges that work great with the KegLand Core 360 Mini CO2 Regulator or the Duotight Mini CO2 Regulator. Comes in a package of 6 cartridges. Please note: due to air shipping restrictions, this product is only eligible for ground shipment within the contiguous United States.

  Read more less

  $11.99

• 

  Beer Line Assembly with Quick Disconnect (QD)

  26 reviews

  A quick and easy draft tubing setup for dispensing your homebrew! This Beer Line Assembly has everything you need to hook a line to your keg and pour. Great for when you're out serving brew on the go or for parties. Includes the ball lock beverage-out quick disconnect, 5 feet of 3/16" beverage tubing, a hand held faucet, and two hose clamps.

  Read more less

  $15.99

• 

  KegLand Cold Activated Keg Filler Stickers | Pack of 4

  Quickly check your fill volume when filling kegs with cold beverage Sticker reacts to cold temperature, turning from yellow to green Apply two stickers on 5-gallon kegs to run the full length of the keg These keg filler stickers are designed to help you quickly check the fill volume, especially when filling cold beverages like cold-crashed beer. When the liquid inside is cold, the color changes from yellow to green. For 5-gallon kegs, you will need to apply 2 stickers if you want the gauge to run the full length of your keg. Size: 8.85" x 0.47" Color Warm: Yellow Color Cold: Green KegLand Part Number: KL42659

  Read more less

  $4.99

• 

  New Corny Keg Lid

  31 reviews

  We love these keg lids as either a replacement or an upgrade to the stock lid featured on many homebrew kegs. Most homebrew kegs feature a straight, parallel bale that sits extemely close to the lid when in the closed position. So close that it can be hard to get a finger or two under the bale to open it. The arms on this lid bend outward creating a nice, easy-to-grip handle to open and close the bale. For use with Torpedo, Cornelius, and Firestone kegs. Comes with a pull-ring pressure relief valve and o-ring. PRV rated to 85 psi.

  Read more less

  $19.99

• 

  Flare Fitting Set - 1/4 in. Nut & 5/16 in. Barb

  9 reviews

  This is a special 1/4" nut and 5/16" barb that will attach to threaded quick disconnects or other 1/4" male flare fittings and allow 5/16" gas tubing to be attached. Stainless Steel barb with a chrome plated Brass nut.

  Read more less

  $4.99

• 

  KegLand Ball Lock Quick Disconnect (QD) | Beverage Out | Flared

  3 reviews

  The most affordable ball lock quick disconnect we offer! Black color easily identifies the QD for beverage use 1/4" flare thread connection The black, beverage-out quick disconnect with male flare fitting. Convenient to use, easy to clean.  Find out for yourself why so many brewers prefer to work with flared keg fittings. Because the fitting-tubing junction is threaded, it can be easily disconnected for cleaning without having to clip your line. Also makes swapping between ball lock and pin lock kegs in the same draft system a snap! Kegland Part Number: KL02974

  Read more less

  $6.59

• 

  KegLand Core 360 Mini CO2 Regulator | Interchangeable Gas Outlet | Swappable Pressure Gauge | SodaStream Compatible

  12 reviews

  Unique Core Puncturing / Actuator results in zero gas lost from screwing in CO2 cartridges Interchangeable ball lock disconnect orientations. 45° for plastic QDs or 90° for stainless QDs 6.5mm Duotight compatible hose barb Swappable mini pressure gauge remains well protected within solid cast brass regulator body Corny-style 65psi Green PRV for added safety and manual depressurizing Switch from 16g to 74g CO2 cartridges with an adapter fitting The new Core 360 Mini CO2 Regulator from KegLand represents a huge jump forward in the mini regulator market. After much feedback on how to make mini regulators more compact, sturdy and efficient, the brilliant engineers at KegLand have come up with this mini-beast. The analog gauge is removable and can be swapped out with a gauge of a different pressure range or it can be swapped out for the Digital Mini Pressure Gauge. Heavy Duty Construction Starting with the body of the regulator, this unit is made from chrome-plated solid cast brass which means it will stand up to quite a bit of abuse. Unlike most mini regulators, the pressure gauge on the Core 360 is safely recessed in the regulator body, so if you ever drop it there is little chance that you'll damage the gauge. What's more, the gauge is removable, so you can swap it out with another mini gauge with a pressure range that better suits your application. Unique Cartridge Connection What really sets this unit apart from other mini regulators is the way in which you insert a CO2 cartridge. A common complaint with these types of regulators is that you can lose a lot of gas from the cartridge just from threading it into the regulator. There's that brief period where the cartridge has been punctured but you haven't fully threaded it into the regulator to form a seal. If you're not quick enough, this can result in a significant amount of lost gas. The Core 360 has a unique design feature where inserting the cartridge is a 2-step process. First you fully thread in the cartridge so it forms a seal before it's opened, and then you screw down the actuator pin to release gas into the regulator. Simple and effective. Furthermore, the Core 360 Mini Regulator is designed to be compatible with both 16g and 74g cartridges. Out of the box it will be ready to accept 16-gram 3/8"-24 UNF threaded cartridges. But with a simple adapter you can switch to 74-gram 5/8"-18 UNF threaded cartridges. Interchangeable Gas Outlet Another feature we haven't seen before on a mini regulator is the interchangeable gas outlet. You can use the swivel nut connection to directly attach the regulator to a flare ball lock disconnect, or you can swap to the 6.5mm Duotight-compatible barb and connect draft tubing. This is a great option if you want to dispense a commercial keg without the need of a ball lock to sanke coupler adapter. The regulator also has two outlet options at either a 45° or 90° angle which makes this the ideal mini regulator regardless of whether you use plastic or stainless steel ball lock disconnects. SodaStream Compatible If you remove the 16g cartridge bushing, you'll find TR21-4 female threads for use with SodaStream gas cylinders. These can be a great option for mobile dispensing as they provide much more gas than a CO2 cartridge and are more easily transported than a full CO2 tank. Includes: KegLand Core 360 Mini Regulator 6.5mm Duotight-compatible hose barb Female Flare Fitting for MFL Disconnects Port end cap 65psi Green PRV SodaStream to 16g thread bushing KegLand Part Number: KL20404 Warning: Do not overtighten onto your cylinder. It is recommended that you use a spanner to hold the neck of your SodaStream cylinder while attaching and detaching the Mini 360 Core Actuator Regulator. Mini 360 Core Actuator Regulator | User Guide

  Read more less

  $82.99

• 

  Used Ball Lock Keg | Corny Keg | Pressure Tested, Cleaned & Sanitized | 5 gal.

  41 reviews

  An affordable option for your first keg or adding to your growing collection These kegs are cleaned, de-labeled, sanitized, pressure tested and guaranteed to hold pressure upon delivery Used kegs may have minor cosmetic damage but are in perfect working order Rubber top and bottoms protect floors from dings These Ball Lock Corny Kegs are a sturdy, reliable keg with the MoreBeer! seal of approval. These corny kegs are cleaned, de-labeled, sanitized, pressure tested and guaranteed to hold pressure upon delivery. Every Ball Lock Cornelius Keg has a 5 gallon capacity and a rubber top and bottom. While these are used kegs with slight cosmetic damages, these light dings and scratches have no effect the keg’s performance. The relief valves, poppets and gaskets on these used kegs are not replaced before shipping, but we sell all of these items separately if you’d like to replace them yourself at home (part numbers KEG540, KEG450 & KEG500). If you’re looking for a truly economical way to serve your beer at home, this Ball Lock Cornelius Keg is a great option. Used keg with minor cosmetic damage only Ball lock corny kegs measure approximately 8.5" (diameter) x 25" (height) x 26 1/4" Height with flare fittings Soda kegs may come with either 11/16 inch body connects or 7/8" body connects Purchase deep sockets to remove body connects (part numbers KEG991 and KEG992)

  Read more less

  $79.99

• 

  Blichmann | QuickCarb™ | Commercial Sankey Keg Coupler Adapter Kit | 12v DC power

  2 reviews

  Love the Blichmann QuickCarb, but want to use it on a commercial sankey keg? Now's your chance! Quickly carbonate beer in commercial sankey style kegs This coupler adapter kit adapts the QuickCarb to work with commercial sanke keg couplers. It also increases the power supplied to the pump to be able to handle full sized 1/2 bbl kegs. Includes: 2 x coupler wing nuts 2 x 1/4 in male flare 2 x coupler washers 12v DC power adapter

  Read more less

  $38.49

• 

  Torpedo Cocktail Keg | US D-Style Spear | Stainless Steel Keg | Low2 Keg Lid O-Ring | Superior Oxygen Barrier Properties

  1 review

  The ideal vessel for serving pre-mixed cocktails and other concoctions on draft Easily pour in your beverage of choice through the wide corny-style lid opening without needing to remove the spear Doubles as a line cleaning keg Rolled handles for a comfortable grip Low2 lid O-ring reduces oxygen ingress by 96% compared to silicone O-rings when measured in a keg! Made by an ISO certified commercial keg manufacturer with high-quality laser welded seams The Torpedo Cocktail Keg is the ideal vessel for serving pre-mixed cocktails and other concoctions on draft. The corny keg style lid makes it easy to pour in your beverage of choice without having to fuss with removing the spear like with standard commercial sanke kegs. Hook up a D-Style keg coupler to begin carbonating the beverage from the bottom up. These kegs provide the added advantage of fully carbonating the entire cocktail. When making drinks on the fly, carbonation is lost quickly since you're mixing carbonated and still ingredients together. But when served from a fully carbonated keg, you can enjoy the bubbles in your glass for longer! Draft lines needing some love? The Torpedo Cocktail keg easily doubles as a line cleaning keg. Simply fill with a batch of LLC or BLC to give your bev lines a little TLC. Low2 Keg Lid O-ring Give your beverage the absolute best protection from oxygen staling with the Low2 keg lid O-ring. Even the most perfectly sealed keg is susceptible to oxygen ingress through the hatch O-ring—yes, even if the keg is under constant pressure with CO2! Even a leak-free, pressurized keg will release CO2 molecules as they pass through the lid O-ring itself, and conversely, Oxygen molecules will permeate through the O-ring and diffuse into the keg when they reach the surface area on the other side. The level of permeability is wide ranging and highly dependent on what material the O-ring is made from. Rather than the usual EPDM or Silicone, Low2 gaskets are made from a unique composition of Synthetic M-Class and Cross-Link Elastomers. This special blend has superior oxygen barrier properties that results in your beverage staying fresher for longer. Specifications: Max Pressure: 130 psi PRV Rating: 85 psi High Quality Laser Welded Seams ISO9001 Quality Assurance Made from 304 Stainless Steel Dimensions:   Height (in.) Diameter (in.) 1.5 Gal 10 9 3/8 2.5 Gal 13 1/4 9 3/8  

  Read more less

  $179.99 - $189.99

• 

  Continuous Soda Carbonator Keg Lid

  14 reviews

  Enjoy a never-ending supply of soda water on tap with the Continuous Soda Carbonator Keg Lid. SodaStream units are great, but filling up those tiny 1L bottles is a pain, they're expensive to swap, and they run out quickly. Hook up your mains water supply to this Carbonator Keg Lid, compatible with any standard ball lock homebrew keg, and you'll never have to think about running out of sparkling water. Setup: Position the keg inside your fridge or kegerator (ideally below 40°F). Attach your beverage draft line to the soda water out post. Attach your gas line to the gas-in post. Set your CO2 regulator to 30-50 psi, depending on how highly carbonated you like your soda water. We highly recommend using a check valve on your CO2 line. On first use, purge the air from the headspace of the keg. Connect the mains water to the water inlet post on the lid of the keg. We recommend also using a check valve on your mains water line to prevent soda water from going back into your house mains. Depending on your mains water pressure, you may need to reduce it using the Duotight In-Line Regulator. For the Carbonator Keg Lid to work well, the mains water pressure should be 10-15 psi higher than your regulator set pressure (from Step 4). That's it. This simple unit will give you continuous soda water connected to your mains water. Please note: if you are using a CO2 regulator that uses a corny-style PRV, such as the KOMOS® regulator, you will need to swap out the standard Green PRV with the 0-100 psi Gray PRV so you can raise the pressure above 60 psi. Always check the pressure rating of your keg(s) before swapping the PRV.   KegLand Part Number: KL10955    

  Read more less

  $76.99

• 

  Duotight Mini CO2 Regulator | 16g & 74g Cartridge Compatible | 6.35mm Duotight Compatible

  Perfect for home use with compact keg setups or on the go for mobile dispensing Compatible with both 16g and 74g CO2 cartridges Features a 6.35mm Duotight-compatible barb for fast, hassle-free keg attachments The Duotight Mini CO2 Regulator is a simple, affordable choice for mini kegs and Oxebar keg setups. This compact regulator is designed to work with both 16g and 74g CO2 cartridges, making it ideal for home use or when you're on the go. With the 6.35mm Duotight-compatible barb you can connect just about anything within a matter of seconds. Simply pair it with the 6.35mm Duotight Ball Lock QD for a quick and hassle-free connection to your kegs. Or, with the Duotight Reducer, you can adapt the regulator for use with the most common and widely used 8mm Duotight accessories. For additional protection against liquid backflow, you can integrate a check valve along with some hosing to safeguard your regulator. Please note if liquid enters the regulator, it's no longer functional. Be extremely careful with overfilling your kegs or tipping them over when the gas has run out. The regulator is capped at 30 psi to ensure you do not accidentally over carbonate or exceed your keg's pressure rating. The gauge reads up to 60 psi to account for potential heat expansion so that it does not break the gauge. Suitable Gas Cartridges: 16g Cartridge 6-pack (KEG993) 74g Cartridge (KEG969) KegLand Part Number: KL42000

  Read more less

  $38.99

• 

  KegLand Ball Lock Quick Disconnect (QD) | Gas In | Flared

  4 reviews

  The most affordable ball lock quick disconnect we offer! White color easily identifies the QD for gas use 1/4" flare thread connection The gray, gas-in quick disconnect with male flare fitting. Convenient to use, easy to clean. Find out for yourself why so many brewers prefer to work with flared keg fittings. Because the fitting-tubing junction is threaded, it can be easily disconnected for cleaning without having to clip your line. Also makes swapping between ball lock and pin lock kegs in the same draft system a snap! Kegland Part Number: KL02967

  Read more less

  $6.59

• 

  Sanke Keg Valve & Spear Removal Tool | D-Style

  35 reviews

  Remove the keg spear from your sanke kegs for cleaning and maintenance For use with US-standard D-Style sanke kegs Safe and easy hand operation Easily and safely remove the valve and spear on American Sanke kegs with this Sanke Valve/Spear Removal Tool from MoreBeer! This economical tool is available for a very competitive price when you order from MoreBeer!, and it is great for anyone who needs to remove their spear on a Sanke keg for cleaning or to repair damage. Note that this tool only presses the spear down to relieve pressure on the retaining ring, you will have to remove the ring by hand.

  Read more less

  $96.99

• 

  Torpedo Keg Picnic Tap Holder

  11 reviews

  Tired of fishing your picnic faucet out of the dirt or the bottom of your kegerator? This holder from Torpedo fits over most ball lock keg posts and holds your hand faucet in convenient, clean position. Made from stainless steel with the Torpedo Keg logo etched in.   Does not fit pin lock kegs.

  Read more less

  $7.99

• 

  Ball Lock Post Bulkhead - Gas In

  3 reviews

  This gas in ball lock bulkhead assembly allows you to add a ball lock post just about anywhere. Create your own pressure vessel or attach it to one of our aluminum gas manifolds for a quick connect option. 1/4" BSP threads and locking nut. Kegland Part Number: KL03179

  Read more less

  $14.49

• 

  KegLand Mini Keg | Ball Lock Tapping Head

  1 review

  Force carbonate and dispense from your KegLand Mini Keg Equipped with Gas-In and Bev-Out keg posts for quick and easy attachment of ball lock disconnects Features a flexible silicone dip tube that draws liquid from the bottom, allowing you to serve from your mini keg whether it's upright or on its side Includes a 35 PSI pressure relief valve (PRV) for safe and controlled carbonation and dispensing Force carbonate and serve from your KegLand Mini Keg with the Ball Lock Tapping Head. The Tapping Head features Gas-In and Bev-Out keg posts and PRV rated to 35 PSI. The flexible silicone dip tube will sink and draw liquid from the bottom of the keg, allowing you to dispense from the keg whether it's standing upright or lying on its side, whichever orientation is more convenient for your refrigerator or cooler. The Tapping Head will add approximately 2.5" to the overall height of your Mini Keg, not including the additional height of your Bev-Out Ball Lock QD. For a more compact dispensing solution, see the Low Profile Tapping Head. Please Note: The dip tube is designed to fit all Mini Kegs, including the largest 10L size. If using a smaller size keg, we recommend cutting the dip tube to the appropriate length so it doesn't bunch up at the bottom of the keg. KegLand Part Number: KL06972

  Read more less

  $39.99

• 

  Torpedo Keg | Ball Lock Keg | Stainless Steel Corny Keg | Low2 Keg Lid O-Ring | Superior Oxygen Barrier Properties | 6 Gallon

  3 reviews

  Oversized corny keg, great for bigger batches and fermentation Low2 lid O-ring reduces oxygen ingress by 96% compared to silicone O-rings when measured in a keg! Brand new, all-stainless construction ball lock keg Stackable with ball lock quick disconnects in place Etched In and Out labels near the keg posts for easy identification Rolled handles for a comfortable grip Made by an ISO certified commercial keg manufacturer with high-quality laser welded seams Set your sights on a brand new Torpedo Keg! The patented, D794,899, sleek all-stainless design represents the pinnacle of quality in ball lock homebrew kegs. With features like welded stainless handles, the ability to stack with fittings in place, amazing quality and a great price we think these kegs will become the standard by which other kegs are measured. Quality First The first thing we at MoreBeer! check out is interior welds. We've spent a decade rejecting kegs made overseas because the interior welds have never met our standards. If a weld is not perfect and shows evident burn marks along with nooks and crannies it cannot be sanitized effectively. These kegs are machine welded and exceed our standards for quality. The weld quality is possible because these kegs made by an ISO certified commercial keg manufacturer. Cool Features Torpedo Kegs were designed to stack with Ball Lock quick disconnects in place and serving which is a cool feature for some brewers who have vertical space in their refrigerator. We also like the rolled stainless steel handles. They are comfortable to grab and will never come off like some rubber handles can over time. In and Out is etched near the keg posts for easy identification which is very handy when you are connecting lines in a refrigerator or kegerator and trying not to make a mistake. Stainless Fermenter We've seen a lot our customers having great success using the 6-gallon Torpedo Keg as a stainless steel fermenter or "kegmenter". The extra headroom that this size offers makes it a great option for fermenting 5-gallon batches. We highly recommend using CellarScience Foam Axe if you're fermenting in the keg. Foam Axe will help reduce krausen buildup, cutting down the chance of clogging issues with the ball lock poppets and the PRV in the keg lid. It should also be noted that leaving your finished beer on the leftover trub from fermentation for too long will eventually lead to off-flavors. If it won't be consumed in 2-3 weeks, transfer your beer to a fresh keg using the Torpedo Keg Buoy which will pick up the clearest beer and leave the sediment behind. Low2 Keg Lid O-ring Give your beverage the absolute best protection from oxygen staling with the Low2 keg lid O-ring. Even the most perfectly sealed keg is susceptible to oxygen ingress through the hatch O-ring—yes, even if the keg is under constant pressure with CO2! Even a leak-free, pressurized keg will release CO2 molecules as they pass through the lid O-ring itself, and conversely, Oxygen molecules will permeate through the O-ring and diffuse into the keg when they reach the surface area on the other side. The level of permeability is wide ranging and highly dependent on what material the O-ring is made from. Rather than the usual EPDM or Silicone, Low2 gaskets are made from a unique composition of Synthetic M-Class and Cross-Link Elastomers. This special blend has superior oxygen barrier properties that results in your beverage staying fresher for longer. Specifications: Max Pressure: 130 psi PRV Rating: 85 psi High Quality Laser Welded Seams ISO9001 Quality Assurance Made from 304 Stainless Steel Dimensions: 27.15" H x 9" D

  Read more less

  $159.99

• 

  Torpedo Keg Ball Lock Quick Disconnect (QD) | Beverage Out | Stainless Steel | Flared

  32 reviews

  Heavy-duty ball lock quick disconnect made from 304 stainless steel for lifetime longevity Etched "Out" label to clearly identify the QD for gas use Pairs perfectly with stainless steel Torpedo Kegs and compatible with all ball lock corny kegs 1/4" flare thread connection Your Kegs are made out of stainless steel, why settle for plastic Quick Disconnects? Upgrade your serving setup to fully Stainless with a pair of Torpedo Ball Lock QDs! These hefty pieces are constructed of 304 SS, designed for lifetime longevity. Printed clearly with "In" and "Out" so even after a few they're easy to work with. Available for both Beer Out and Gas In, with either Barbed or Flared connections. See YMAN's below for the appropriate connectors! A flare fitting washer (KEG602) is recommended for use with this product. Perfect with our Torpedo Kegs, these will work with any Ball Lock Corny Keg. Features: 304 SS Construction - Built to last a lifetime 1/4" Flare connection Ball Lock Beverage Out 2" Height

  Read more less

  $24.99

• 

  Red PRV 1881 Cap Combo (35 psi)

  1 review

  Designed for use with the PCO38 Tapping Head. With female PCO1881 threads, it can also be used with the FermZilla Collection Container or Hop Bong Sight Glasses. The Red PRV is rated to 35 psi (2.5 BAR). Warning: Never exceed the pressure capabilities of your vessel. PRV's are not spunding valves! KegLand Part Number: KB10537

  Read more less

  $12.49

• 

  CMBecker Ball Lock Quick Disconnect (QD) | Built-In Check Valve | Gas In | Flared | High-Quality Plastic QD | NSF Registered | Made in Germany | Assembled in USA

  9 reviews

  The highest quality plastic ball lock quick disconnect available to homebrewers Built-in check valve to prevent liquid from backflowing into your draft system Smooth operation—clicks into place on keg posts and is easily removed Built-in flare washer—no need for a separate nylon washer that is required with stainless steel QDs CMBecker is an international manufacturer of beverage dispensing solutions for both home and professional draft equipment Gray plastic clearly identifies the disconnect as the gas in QD Sleep a little easier knowing this gas in ball lock with built-in check valve has your back. The internal check valve allows gas to flow out, but won't allow backflow of liquid into your gas system. Many manifolds and regulators already feature check valves, but this disconnect will keep liquid from ever entering your gas lines in the first place. Especially handy if you force carbonate your beer using the bev out dip tube! Why we love it:  Because we've had beer shoot back into our gas line and that sucks. At some point you will have a keg that is pressurized more than the pressure in your gas system. This could be caused by different carbonation levels, a keg sitting at room temperature, etc. So for example if the pressure in your keg is at 20 psi and your regulator is set at 12 psi, when you connect your gas in quick-disconnect liquid shoots from the keg into the gas line. Eliminate that possibility with this ingenious fitting.      Features: Internal Check Valve protects your system from liquid back flow Made in Germany and assembled in the USA by CMB. Extremely high quality for years of service. NSF Approved for Food Grade Service!

  Read more less

  $15.99

• 

  Gasket | Dip Tubes | Corny Keg Part

  2 reviews

  Slide gasket onto dip tube and then place dip tube back in keg. 5/16" ID with a 7/64" cross section. Made of FDA BUNA N

  Read more less

  $0.49

• 

  Replacement PRV | Pull Ring Pressure Relief Valve | Gray | 100 PSI

  9 reviews

  A replacement pull-ring style relief valve for your favorite keg!   This is the most common relief valve. Fits most Cornelius and Firestone style kegs, along with many others. Features a long body with spring, and gray top with pull ring.    Max. pressure rating: 100 psi   Kegland Part Number: KL03070

  Read more less

  $8.79

• 

  CoolBrew Corny Keg Cooler 5 gal.

  18 reviews

  Keep your kegs insulated with the new CoolBrew Keg Coolers. Specifically built for Cornelius kegs, these jackets will preserve your precious brew for longer when you take a keg out to share with friends. They come a little oversized to give you extra room for ice or ice packs. This one is perfectly sized for 5 gallon Cornelius kegs. Features: Made from durable polyester Comes with a shoulder strap for easy transport Insulation can keep kegs cold for hours Zipper on top provides easy access to tap and QDs 100% waterproof 26.5 in. Tall x 12 in. Diameter

  Read more less

  $59.99

• 

  Torpedo Keg Ball Lock Quick Disconnect (QD) | Gas In | Stainless Steel | Flared

  30 reviews

  Heavy-duty ball lock quick disconnect made from 304 stainless steel for lifetime longevity Etched "In" label to clearly identify the QD for beverage use Pairs perfectly with stainless steel Torpedo Kegs and compatible with all ball lock corny kegs 1/4" flare thread connection Your Kegs are made out of stainless steel, why settle for plastic Quick Disconnects? Upgrade your serving setup to fully Stainless with a pair of Torpedo Ball Lock QDs! These hefty pieces are constructed of 304 SS, designed for lifetime longevity. Printed clearly with "In" and "Out" so even after a few they're easy to work with. Available for both Beer Out and Gas In, with either Barbed or Flared connections. See YMAN's below for the appropriate connectors! A flare fitting washer (KEG602) is recommended for use with this product. Perfect with our Torpedo Kegs, these will work with any Ball Lock Corny Keg. Features: 304 SS Construction - Built to last a lifetime 1/4" Flare connection Clearly Labeled Ball Lock Gas In 2" Height

  Read more less

  $24.99

• 

  EVABarrier Beer Line Assembly - Ball Lock Quick Disconnect (QD)

  5 reviews

  The most advanced Beer Tubing Assembly we offer, featuring EVABarrier double-walled draft tubing and Duotight push-to-connect fittings. This double walled tubing offers superior protection against oxidation, CO2 loss and microbial growth. Plus, it's BPA and PVC free! EVA tubing is the future of draft line for professional applications, and now you can dispense beer on the go with the same first-class tubing. Includes 5.5 ft. of 4mm ID x 8mm OD EVABarrier, which should give you the perfect back pressure to control foaming issues. The hand held faucet features a Duotight compatible barb so it can connect directly to the Duotight reducer. At the other end is a ball lock quick disconnect with flare Duotight fitting. Inner Diameter - 4 mm (5/32") Outer Diameter - 8 mm (5/16") PVC, BPA , and Plasticizer Free* Outer wall prevents oxidation and CO2 loss Smooth inner wall prevents microbial growth build-up   *EVABarrier does not contain plasticizers, or phthalates, that are used to make PVC flexible. These plasticizers are known to leach out into the beer over time and have adverse health effects. ** Unit does not come pre-assebmled.  

  Read more less

  $19.99

• 

  Universal Poppet | Corny Keg Part

  14 reviews

  A great way to repair your keg, even if you're not sure what type you have! This poppet works on all of the kegs that we sell, Pin or Ball lock! Poppets are pretty easy to damage or lose while cleaning your keg, and having a couple extra universal poppets on hand is a great way to make sure that you can always serve your homebrew! Compatible with our ball and pin lock replacement body connects - KEG460G, KEG470G, KEG1100, KEG1101.

  Read more less

  $4.39

• 

  Megamouth Torpedo Keg | Ball Lock Keg | Stainless Steel Corny Keg

  1 review

  The Megamouth Torpedo Keg series features an extra-large lid opening for easy cleaning Brand new, all-stainless construction ball lock keg Stackable with ball lock quick disconnects in place Etched In and Out labels near the keg posts for easy identification Rolled handles for a comfortable grip Made by an ISO certified commercial keg manufacturer with high-quality laser welded seams The Megamouth Torpedo Kegs are by far the easiest to clean and maintain out of any ball lock homebrew keg you'll find. With an extra-large lid opening, even the buffest of homebrewer (we hear they do exist!) will have no trouble reaching in for a good scrub when it kicks—no expensive keg washing contraptions needed! The Megamouth makes for an excellent pressurizable fermentation vessel and is the ideal choice for brewers who prefer to add dry hops and other flavoring ingredients directly to the keg. Quality First Here at MoreBeer! we love nothing more than quality interior welds. We've spent a decade rejecting kegs made overseas because the interior welds have never met our standards. If a weld is not perfect and shows evident burn marks along with nooks and crannies it cannot be sanitized effectively. Torpedo kegs are machine welded and exceed our standards for quality. This weld quality is possible because these kegs are made by an ISO certified commercial keg manufacturer. Cool Features Torpedo Kegs were designed to stack with Ball Lock quick disconnects in place and serving which is a cool feature for some brewers who have vertical space in their refrigerator. We also like the rolled stainless steel handles. They are comfortable to grab and will never come off like some rubber handles can over time. “In” and “Out” is etched near the keg posts for easy identification which is very handy when you are connecting lines in a refrigerator or kegerator and trying not to make a mistake. Overall for the price and quality, along with free shipping from MoreBeer!, the Torpedo Keg is an amazing value! Specifications: Mouth Opening: 5.8" L x 4.8" W. Max Pressure: 130 psi PRV Rating: 85 psi High Quality Laser Welded Seams ISO9001 Quality Assurance Made from 304 Stainless Steel Dimensions:   Height (in.) Diameter (in.) 3 Gal 13.4 11.4 5 Gal 17.9 11.4 6 Gal 20.5 11.4 10 Gal 30.3 11.4  

  Read more less

  $169.99 - $249.99

• 

  KegLand Mini Keg | Low Profile Ball Lock Tapping Head

  2 reviews

  Force carbonate and dispense from your KegLand Mini Keg Low profile design minimizes overall height to help fit your keg in a cooler or compact refrigerator Includes Gas-In and Bev-Out Ball Lock Caps for quick and easy attachment of ball lock disconnects Dip tube filter attachment blocks sediment so you pour the clearest beer possible Force carbonate and serve from your KegLand Mini Keg with the Low Profile Ball Lock Tapping Head. The Low Profile Tapping Head only adds approximately 1.5" to the overall height of the keg, making it the ideal dispensing solution if you need to fit your keg into a cooler or compact refrigerator. Includes PRV rated to 35 PSI and Gas-In and Bev-Out Ball Lock Caps for quick and easy attachment of ball lock disconnects. The filtered dip tube will block any sediment inside the keg so you'll be pouring the clearest beer possible. If you'd prefer stainless steel keg posts over the plastic Ball Lock Caps, see the standard Ball Lock Tapping Head. KegLand Part Number: KL24822

  Read more less

  $34.99

• 

  Flare Fitting - Washer

  13 reviews

  Nylon washer used with 1/4 inch flare fittings. Use the washer anywhere you have metal to metal contact on flare fittings to prevent leaks. This can be on certain types of regulator connections and with stainless steel quick disconnects (like the Torpedo Quick Disconnects) This gasket is not necessary when connecting female flare fittings to the plastic MFL quick disconnects because they have a plastic washer built in.

  Read more less

  $0.49

• 

  CMBecker Ball Lock Quick Disconnect (QD) | Beverage Out | Barbed | High-Quality Plastic QD | NSF Registered | Made in Germany | Assembled in USA

  1 review

  The highest quality plastic ball lock quick disconnect available to homebrewers Smooth operation—clicks into place on keg posts and is easily removed 1/4" barb for 1/4" or 3/16" ID draft line CMBecker is an international manufacturer of beverage dispensing solutions for both home and professional draft equipment Black plastic clearly identifies the disconnect as the liquid out QD This black, beverage out quick disconnect comes with a barb for attaching to a beverage line, and it's made by CM Becker so you know it is high quality. The barb measures 1/4", so 3/16" beverage tubing is recommend for the perfect fit.  Note: Sometiems ball lock fittings can be difficult to get fully seated on a Cornelius keg. We recommend using a quick spray of sanitizer solution to act as a lubricant and giving it a few twists while applying the ball lock.

  Read more less

  $7.29

• 

  PVC Free Gas Tubing Assembly - Ball Lock Quick Disconnect (QD)

  9 reviews

  An upgraded version of our popular Gas Tubing Assembly. Our new assembly now includes 5 ft of 5/16" Ultra Barrier Gas™ PVC Free Beer Tubing, ball lock gas-in quick disconnect (barb) and two hose clamps. EJ Beverages' cutting edge Ultra Barrier Gas™ tubing has a number of advantages over regular Vinyl tubing: Clear tubing with red stripe for identification as low pressure gas line PVC Free and BPA Free - containes no DEHP phthalates or other plasticizers Environmentally friendly production - does not emit dioxins Remains flexible at lower temperatures Temperature range of -40 to 125° F Pressure rated up to 60 psi

  Read more less

  $16.99

• 

  Corny Keg Ball Lock Quick Disconnect (QD) Jumper Line

  24 reviews

  Connect two ball lock homebrewing kegs together via their ball lock our fittings. Handing for moving sanitizer or beer from one keg to the next. We often use this fitting when we have a big party where we dixie chain kegs together.  For example if you made 10 gallons of pale ale you can use this jumper to connect the two kegs so that all 10 gallons can pour at once.  

  Read more less

  $17.99

Show more products