Stainless steel splicer fitting for joining different sizes of tubing. Recommended for splicing 3/16" or 1/4" ID tubing to 3/8" ID tubing. One end is slightly undersized at 6 mm (0.24") and the other is slightly oversized at 10 mm (0.39").
Made from 304 stainless steel.
Stainless steel splicer fitting for joining different sizes of tubing. Recommended for splicing 3/16" or 1/4" ID tubing to 5/16" or 3/8" ID tubing. The barbs are slightly undersized at 6 mm (0.24") and 8 mm (0.31").
Made from 304 stainless steel.
Stainless steel splicer fitting for joining different sizes of tubing. Recommended for splicing 3/8" tubing to 1/2" ID tubing. The barbs are slightly oversized at 10 mm (0.39") and 13 mm (0.51").
Made from 304 stainless steel.
Stainless steel splicer fitting for joining different sizes of tubing. Recommended for splicing 1/4" or 5/16" ID tubing to 3/8" ID tubing. The 3/8" barb is slightly oversized at 10 mm (0.39").
Made from 304 stainless steel.
Compatible with either your sanke keg coupler or draft shank and held in place with a hex nut & gasket. This 1/4 in. tailpiece is commonly used with 3/16 in. ID draft tubing for a tight fit.
Comes in a convenient zip lock bag.
Compatible with either your sanke keg coupler or draft shank and held in place with a hex nut & gasket. This 5/16 in. tailpiece is commonly used with 1/4 in. ID draft tubing for a tight fit.
Comes in a convenient zip lock bag.
This 3-way stainless steel tee is perfect for splitting gas lines to push multiple kegs with one CO2 cylinder. Slightly oversized at 13 mm OD (0.51") for a tighter fit with 1/2" ID tubing.
This 3-way stainless steel tee is perfect for splitting gas lines to push multiple kegs with one CO2 cylinder. Slightly oversized at 10 mm OD (0.39") for a tighter fit with 3/8" ID tubing.
1" stainless steel hex nut. Used to attach a tailpiece barb to either a faucet shank or keg coupler. You will also need a tailpiece gasket to form a seal. See below for EPDM, Silicone, and Vinyl options.
Female Beer Thread (5/8" BSP)
5/8" top port opening
Comes in a convenient zip lock bag.
Connect draft tubing to your keg coupler or faucet shank. Recommended for 3/16" or 1/4" ID draft lines. Tailpiece and hex nut are made of stainless steel.
Universal keg post o-rings can be used with both ball lock and pin lock homebrew kegs. These o-rings go on the outside of your homebrew keg posts (also referred to as body connects) which is where you connect your ball lock or pinlock quick disconnects.
Comes in a convenient zip lock bag.
Universal Poppets can be used with both ball lock and pin lock homebrew kegs. Poppets are one of the critical parts that makes the keg function, so it's always a good idea to have spares on hand. This 10-pack of Universal Poppets represents a great value for brewers buying in bulk.
Comes in a convenient zip lock bag.
These 5/8" Vinyl gaskets are used anywhere you're mounting a tailpiece. This could be on the back of your draft faucet shank or on either port of a commercial keg coupler.
Comes in a convenient zip lock bag.
Control the humidity of your cellar to prevent wine barrels from drying out Dry, non-humidified barrels will draw liquid to the outer surface where it evaporates, leading to significant product loss Can operate in environments as low as 34°F, making it ideal for cold rooms and storage halls Compact, stand-alone unit can be suspended from or mounted to a wall 2,800 cubic feet per hour air flow Made in Germany by Kreyer Humidity control in wine cellars plays a major role during the production, maturation and storage of wine and other beverages in wooden barrels. Wine barrels safe-guard the main asset of a winery – the wine itself. The wooden walls of dry, non-humidified barrels will draw liquid from inside it up through the small crevices to the outer surface where it evaporates. Over time, this leads to a significant amount of product loss. For example, a 225L wine barrel can lose 10-15% of the wine volume over one year. A professional humidification of the barrel room allows the barrel wood to absorb water-vapor, the crevices fill out and loss of wine is prevented. A well-kept barrel room is therefore cool, usually around 57-60°F and humidified at about 75% - 80% rH. As with every aspect of winemaking, attention and professional equipment are required. Low humidification may allow the wood to dehydrate and wine will evaporate through it, while overly high humidity can lead to mold and fungus. The centrifugal humidifier HumiFix is equipped with a spinning disk that vaporizes water into very fine droplets that can be easily absorbed by the surrounding air, humidifying and cooling a room at the same time. The unit can work either connected to your main water supply with inline cartridge filtration or more ideally to an RO unit. The HumiFix can work at low temperatures (down to 34°F), which is ideal for installation in cold rooms and storage halls. Features:
Stand-alone unit Easy installation and handling Compact construction Wall or suspended mounting Specifications:
Water Output: 1.0 L/h (0.26 Gal/h) Air Flow: 80 m³/h Power: 31 watts Power Connection: 110V/1Ph/60Hz Dimensions: 15.5" L x 12" W x 15.5" H Empty Weight: 10 lbs Please note: this unit comes with a bare cord so it can be hard wired to a controller. Otherwise we recommend attaching a 110V male plug and using it with the Inkbird Digital Humidity Controller.
Control the humidity of your cellar to prevent wine barrels from drying out Dry, non-humidified barrels will draw liquid to the outer surface where it evaporates, leading to significant product loss Can operate in environments as low as 34°F, making it ideal for cold rooms and storage halls Compact, stand-alone unit can be suspended from or mounted to a wall 9,900 cubic feet per hour air flow Made in Germany by Kreyer Humidity control in wine cellars plays a major role during the production, maturation and storage of wine and other beverages in wooden barrels. Wine barrels safe-guard the main asset of a winery – the wine itself. The wooden walls of dry, non-humidified barrels will draw liquid from inside it up through the small crevices to the outer surface where it evaporates. Over time, this leads to a significant amount of product loss. For example, a 225L wine barrel can lose 10-15% of the wine volume over one year. A professional humidification of the barrel room allows the barrel wood to absorb water-vapor, the crevices fill out and loss of wine is prevented. A well-kept barrel room is therefore cool, usually around 57-60°F and humidified at about 75% - 80% rH. As with every aspect of winemaking, attention and professional equipment are required. Low humidification may allow the wood to dehydrate and wine will evaporate through it, while overly high humidity can lead to mold and fungus. The centrifugal humidifier HumiFix is equipped with a spinning disk that vaporizes water into very fine droplets that can be easily absorbed by the surrounding air, humidifying and cooling a room at the same time. The unit can work either connected to your main water supply with inline cartridge filtration or more ideally to an RO unit. The HumiFix can work at low temperatures (down to 34°F), which is ideal for installation in cold rooms and storage halls. Features:
Stand-alone unit Easy installation and handling Compact construction Wall or suspended mounting Specifications:
Water Output: 6.5 L/h (1.69 Gal/h) Air Flow: 280 m³/h Power: 230 watts Power Connection: 110V/1Ph/60Hz Dimensions: 24" L x 20" W x 22.25" H Empty Weight: 40 lbs Please note: this unit comes with a bare cord so it can be hard wired to a controller. Otherwise we recommend attaching a 110V male plug and using it with the Inkbird Digital Humidity Controller.
Due to high demand, this item is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this to you when we receive more inventory.
Compact chiller with commercial level cooling power
Maintain fermentation temperatures, cold-stabilize insulated tanks, or maintain storage temperatures
Position inside the winery or outside in a covered position
Fill from the exterior without the need to remove covers or panels
Program and monitor temperatures via the digital controller
Made in Germany by Kreyer
This Chilly45 unit allows you to easily cool your ferment temperatures, cold-stabilize smaller insulated tanks, or maintain a wine tank storage temperature. This unit can be used inside the winery or placed in a covered position on the outside of the winery. Manufactured by Kreyer, the World's leading producers of wine-cooling equipment.
Ready to go - fill with water or a water/glycol solution and plug in. They are equipped with an efficient scroll-type compressor.
Note: This unit runs off 208V single phase power. It will not run off 220V.
Uses
Cooling of must for cold soaks, slow starting ferments
Stabilization of tataric crystals
Controlling fermenting temperatures
Maintaining storage temperatures in tanks/barrels (ask about our barrel snake!)
Features
Sheet metal housing, electrolitic galvanized high surface quality, powder-coated and abrasion-resistant encasing cover that is easily detachable
208v single phase 60Hz 14 amp supply voltage
1.28 tons (15,000 btu) of cooling power
30L/8G Insulated Plastic tank to hold water or glycol
Easy to fill from outside
Centrifugal recirculation pump made by Speck.
Digital Thermostat
Integrated pump pressure switch allows unit to work with digital automatic temperature controlers on multiple tanks.
NEW Micro Channel evaporator is quieter, more efficient and uses 30% less cooling gas.
High Tech, Scroll-type, efficient, low noise compressor
R513a refrigerant
Non-Ferrous water circuit - No Rusting!
Outlet is 3/4" MPT, which accomodates hose fittings with gaskets, and includes a 1/2" barb fitting
29.75" Length
23.6" Width
19.68" Height
All units pass multiple tests prior to shipment
6 Month Electrical Warranty
1 Year Mechanical Warranty
CE Certified
Need a small glycol system designed for your needs? Contact Morebeer! Pro at info@morebeerpro.com or MoreWine! Pro at info@morewinepro.com
Due to high demand, this item is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this item to you when we receive more inventory.
Compact chiller with commercial level cooling power
Maintain fermentation temperatures, cold-stabilize insulated tanks, or maintain storage temperatures
Position inside the winery or outside in a covered position
Fill from the exterior without the need to remove covers or panels
Program and monitor temperatures via the digital controller
Made in Germany by Kreyer
This Chilly45 unit allows you to easily cool your ferment temperatures, cold-stabilize smaller insulated tanks, or maintain a wine tank storage temperature. This unit can be used inside the winery or placed in a covered position on the outside of the winery. Manufactured by Kreyer, the World's leading producers of wine-cooling equipment.
Ready to go - fill with water or a water/glycol solution and plug in. They are equipped with an efficient scroll-type compressor.
Note: This unit runs off 220V single phase power. It will not run off 208V.
Uses
Cooling of must for cold soaks, slow starting ferments
Stabilization of tataric crystals
Controlling fermenting temperatures
Maintaining storage temperatures in tanks/barrels (ask about our barrel snake!)
Features
Sheet metal housing, electrolitic galvanized high surface quality, powder-coated and abrasion-resistant encasing cover that is easily detachable
220v single phase 60Hz 14 amp supply voltage
1.28 tons (15,000 btu) of cooling power
30L/8G Insulated Plastic tank to hold water or glycol
Easy to fill from outside
Centrifugal recirculation pump made by Speck.
Digital Thermostat
Integrated pump pressure switch allows unit to work with digital automatic temperature controlers on multiple tanks.
NEW Micro Channel evaporator is quieter, more efficient and uses 30% less cooling gas.
High Tech, Scroll-type, efficient, low noise compressor
Non-Ferrous water circuit - No Rusting!
Outlet is 3/4" MPT, which accomodates hose fittings with gaskets, and includes a 1/2" barb fitting
29.75" Length
23.6" Width
19.68" Height
All units pass multiple tests prior to shipment
6 Month Electrical Warranty
1 Year Mechanical Warranty
CE Certified
Need a small glycol system designed for your needs? Contact Morebeer! Pro at info@morebeerpro.com or MoreWine! Pro at info@morewinepro.com
Due to high demand, this item is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this item to you when we receive more in late May.
Compact chiller with commercial level cooling power
Maintain fermentation temperatures, cold-stabilize insulated tanks, or maintain storage temperatures
Position inside the winery or outside in a covered position
Fill from the exterior without the need to remove covers or panels
Program and monitor temperatures via the digital controller
Made in Germany by Kreyer
This Chilly45 unit allows you to easily cool your ferment temperatures, cold-stabilize smaller insulated tanks, or maintain a wine tank storage temperature. This unit can be used inside the winery or placed in a covered position on the outside of the winery. Manufactured by Kreyer, the World's leading producers of wine-cooling equipment.
Ready to go - fill with water or a water/glycol solution and plug in. They are equipped with an efficient scroll-type compressor.
Note: This unit runs off 220V single phase power. It will not run off 208V.
Uses
Cooling of must for cold soaks, slow starting ferments
Stabilization of tataric crystals
Controlling fermenting temperatures
Maintaining storage temperatures in tanks/barrels (ask about our barrel snake!)
Features
Sheet metal housing, electrolitic galvanized high surface quality, powder-coated and abrasion-resistant encasing cover that is easily detachable
220v single phase 60Hz 14 amp supply voltage
1.28 tons (15,000 btu) of cooling power
30L/8G Insulated Plastic tank to hold water or glycol
Easy to fill from outside
Centrifugal recirculation pump made by Speck.
Digital Thermostat
Integrated pump pressure switch allows unit to work with digital automatic temperature controlers on multiple tanks.
NEW Micro Channel evaporator is quieter, more efficient and uses 30% less cooling gas.
High Tech, Scroll-type, efficient, low noise compressor
Non-Ferrous water circuit - No Rusting!
Outlet is 3/4" MPT, which accomodates hose fittings with gaskets, and includes a 1/2" barb fitting
29.75" Length
23.6" Width
19.68" Height
All units pass multiple tests prior to shipment
6 Month Electrical Warranty
1 Year Mechanical Warranty
CE Certified
Need a small glycol system designed for your needs? Contact Morebeer! Pro at info@morebeerpro.com or MoreWine! Pro at info@morewinepro.com
Cooling & heating in one premium quality unit
Control fermentation temperatures, cold-stabilize insulated tanks, or heat tanks during cold weather
Fill from the exterior without the need to remove covers or panels
Program and monitor temperatures via the digital controller
Non-Return Kit installed as standard to prevent backflow when positioned below your tank jacket, heat exchanger, or piping system
Four locking casters offer ease-of-mobility when moving the unit around the winery
3 Ton / 43,000 Btu cooling capacity
230V, Single Phase power
Made in Germany by Kreyer
Cooling and Heating in one unit!
Every Winemaker can appreciate the benefits of precise temperature control during all stages of production. This mobile unit allows you to easily control your ferment temperatures, heat your tanks during winter to expedite Malo-Lactic fermentation, or cold-stabilize your white wines. This unit can be used as portable unit in a larger winery or as a fixed system supplying a glycol loop in a smaller winery. Unit is used for heating or cooling but cannot supply both at the same time.
Manufactured by Kreyer, the World's leading producers of wine-cooling equipment.
Note: This unit runs off 230V single phase power. It will not run off 208V.
Uses:
Cooling of must for cold soaks, slow starting ferments
Heating up must after a cold soak period
Cold Stabilization of tartaric crystals
Controlling fermenting temperatures through cooling or heating
Maintaining storage temperatures in tanks/barrels
Check out these features:
Cools or Heats
Over 3 Tons (43,000btu) of cooling power (larger Chilly Max's are available)
.85 Tons of heating power
Can cool glycol/water bath down to -10C/14F or up to 42C/107F
230V 60Hz Single phase Power supply Required
Rolls on four locking casters
Sheet metal housing, electrolytic galvanized high surface quality, powder-coated and abrasion-resistant casing
7 Gallon Insulated Plastic glycol/water reservoir
Easy to fill from outside
Evaporator coil made of stainless steel
High-quality Grundfos recirculation pump
Built in pressure switch shuts down recirculation pump when not needed
Digital Thermostat
Lifting/Crane Hooks for transport
All panels remove for easy access
All units pass multiple tests prior to shipment
German Engineering
Controlled by compact PC boards with a temperature accuracy up to 0.1 degree Celsius.
29.5"L x 34.6"W x 39.4"T
Unit has 1" Male BSP w/ 3/4" Female BSP inlet / outlet
6 Month Electrical Warranty
1 Year Mechanical Warranty
CE Certified
Please Note: This unit REQUIRES 230 v Single Phase power and will not function on anything else. Please confirm that you have the proper power for this unit before purchasing, and plan to have a qualified electrician wire the necessary plug to the cord.
Cooling & heating in one premium quality unit Control fermentation temperatures, cold-stabilize insulated tanks, or heat tanks during cold weather Fill from the exterior without the need to remove covers or panels Program and monitor temperatures via the digital controller Non-Return Kit installed as standard to prevent backflow when positioned below your tank jacket, heat exchanger, or piping system Four locking casters offer ease-of-mobility when moving the unit around the winery 1.8 Ton / 21,840 Btu cooling capacity 208V, 3 Phase power Made in Germany by Kreyer Cooling and Heating in one unit! Every Winemaker can appreciate the benefits of precise temperature control during all stages of production. This mobile unit allows you to easily control your ferment temperatures, heat your tanks during winter to expedite Malo-Lactic fermentation, or cold-stabilize your white wines. This unit can be used as portable unit in a larger winery or as a fixed system supplying a glycol loop in a smaller winery. Unit is used for heating or cooling but cannot supply both at the same time. Manufactured by Kreyer, the World's leading producers of wine-cooling equipment. Uses: Cooling of must for cold soaks, slow starting ferments Heating up must after a cold soak period Cold Stabilization of tartaric crystals Controlling fermenting temperatures through cooling or heating Maintaining storage temperatures in tanks/barrels Check out these features: Cools or Heats 1.8 Tons (21,840btu) of cooling power .85 Tons of heating power Can cool glycol/water bath down to -10C/14F or up to 42C/107F 208V 60Hz 3 phase supply voltage drawing 13.1 amps Rolls on four locking casters Sheet metal housing, electrolytic galvanized high surface quality, powder-coated and abrasion-resistant casing 7 Gallon Insulated Plastic glycol/water reservoir Easy to fill from outside Evaporator coil made of stainless steel High-quality Grundfos recirculation pump Built in pressure switch shuts down recirculation pump when not needed Digital Thermostat Lifting/Crane Hooks for transport All panels remove for easy access All units pass multiple tests prior to shipment German Engineering Controlled by compact PC boards with a temperature accuracy up to 0.1 degree Celsius. 33"L x 25"W x 31.5"T Unit has 1" Male BSP w/ 3/4" Female BSP inlet / outlet 6 Month Electrical Warranty 1 Year Mechanical Warranty CE Certified Please Note: This unit REQUIRES 208 v Three Phase power and will not function on anything else. Please confirm that you have the proper power for this unit before purchasing, and plan to have a qualified electrician wire the necessary plug to the cord. Available in larger sizes. For additional product options View the resource.
Cooling & heating in one premium quality unit Control fermentation temperatures, cold-stabilize insulated tanks, or heat tanks during cold weather Fill from the exterior without the need to remove covers or panels Program and monitor temperatures via the digital controller Non-Return Kit installed as standard to prevent backflow when positioned below your tank jacket, heat exchanger, or piping system Four locking casters offer ease-of-mobility when moving the unit around the winery 1.8 Ton / 21,840 Btu cooling capacity 230V, 3 Phase power Made in Germany by Kreyer Cooling and Heating in one unit! Every Winemaker can appreciate the benefits of precise temperature control during all stages of production. This mobile unit allows you to easily control your ferment temperatures, heat your tanks during winter to expedite Malo-Lactic fermentation, or cold-stabilize your white wines. This unit can be used as portable unit in a larger winery or as a fixed system supplying a glycol loop in a smaller winery. Unit is used for heating or cooling but cannot supply both at the same time. Manufactured by Kreyer, the World's leading producers of wine-cooling equipment. Note: This unit runs off 230V 3 phase power. It will not run off 208V. Uses: Cooling of must for cold soaks, slow starting ferments Heating up must after a cold soak period Cold Stabilization of tartaric crystals Controlling fermenting temperatures through cooling or heating Maintaining storage temperatures in tanks/barrels Check out these features: Cools or Heats 1.8 Tons (21,840btu) of cooling power .85 Tons of heating power Can cool glycol/water bath down to -10C/14F or up to 42C/107F 230V 60Hz 3 phase supply voltage drawing 13.1 amps Rolls on four locking casters Sheet metal housing, electrolytic galvanized high surface quality, powder-coated and abrasion-resistant casing 7 Gallon Insulated Plastic glycol/water reservoir Easy to fill from outside Evaporator coil made of stainless steel High-quality Grundfos recirculation pump Built in pressure switch shuts down recirculation pump when not needed Digital Thermostat Lifting/Crane Hooks for transport All panels remove for easy access All units pass multiple tests prior to shipment German Engineering Controlled by compact PC boards with a temperature accuracy up to 0.1 degree Celsius. 33"L x 25"W x 31.5"T Unit has 1" Male BSP w/ 3/4" Female BSP inlet / outlet 6 Month Electrical Warranty 1 Year Mechanical Warranty CE Certified Please Note: This unit REQUIRES 230 v Three Phase power and will not function on anything else. Please confirm that you have the proper power for this unit before purchasing, and plan to have a qualified electrician wire the necessary plug to the cord. Available in larger sizes. For additional product options View the resource.
Due to high demand, this item is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this item to you when we receive inventory.
Cooling & heating in one premium quality unit
Control fermentation temperatures, cold-stabilize insulated tanks, or heat tanks during cold weather
Fill from the exterior without the need to remove covers or panels
Program and monitor temperatures via the digital controller
Non-Return Kit installed as standard to prevent backflow when positioned below your tank jacket, heat exchanger, or piping system
Four locking casters offer ease-of-mobility when moving the unit around the winery
1.8 Ton / 21,840 Btu cooling capacity
230V, Single Phase power
Made in Germany by Kreyer
Cooling and Heating in one unit!
Every Winemaker can appreciate the benefits of precise temperature control during all stages of production. This mobile unit allows you to easily control your ferment temperatures, heat your tanks during winter to expedite Malo-Lactic fermentation, or cold-stabilize your white wines. This unit can be used as portable unit in a larger winery or as a fixed system supplying a glycol loop in a smaller winery. Unit is used for heating or cooling but cannot supply both at the same time.
Manufactured by Kreyer, the World's leading producers of wine-cooling equipment.
Note: This unit runs off 230V single phase power. It will not run off 208V.
Uses:
Cooling of must for cold soaks, slow starting ferments
Heating up must after a cold soak period
Cold Stabilization of tartaric crystals
Controlling fermenting temperatures through cooling or heating
Maintaining storage temperatures in tanks/barrels
Check out these features:
Cools or Heats
1.8 Tons (21,840btu) of cooling power
.85 Tons of heating power
Can cool glycol/water bath down to -10C/14F or up to 42C/107F
230V 60Hz Single phase Power supply Required
Rolls on four locking casters
Sheet metal housing, electrolytic galvanized high surface quality, powder-coated and abrasion-resistant casing
7 Gallon Insulated Plastic glycol/water reservoir
Easy to fill from outside
Evaporator coil made of stainless steel
High-quality Grundfos recirculation pump
Built in pressure switch shuts down recirculation pump when not needed
Digital Thermostat
Lifting/Crane Hooks for transport
All panels remove for easy access
All units pass multiple tests prior to shipment
German Engineering
Controlled by compact PC boards with a temperature accuracy up to 0.1 degree Celsius.
33"L x 25"W x 31.5"T
Unit has 1" Male BSP w/ 3/4" Female BSP inlet / outlet
6 Month Electrical Warranty
1 Year Mechanical Warranty
CE Certified
Please Note: This unit REQUIRES 230 v Single Phase power and will not function on anything else. Please confirm that you have the proper power for this unit before purchasing, and plan to have a qualified electrician wire the necessary plug to the cord.
Available in larger sizes. For additional product options View the resource.
Cooling & heating in one premium quality unit Control fermentation temperatures, cold-stabilize insulated tanks, or heat tanks during cold weather Fill from the exterior without the need to remove covers or panels Program and monitor temperatures via the digital controller Non-Return Kit installed as standard to prevent backflow when positioned below your tank jacket, heat exchanger, or piping system Four locking casters offer ease-of-mobility when moving the unit around the winery 3 Ton / 36,000 Btu cooling capacity 208V, 3 Phase power Made in Germany by Kreyer Cooling and Heating in one unit! Every Winemaker can appreciate the benefits of precise temperature control during all stages of production. This mobile unit allows you to easily control your ferment temperatures, heat your tanks during winter to expedite Malo-Lactic fermentation, or cold-stabilize your white wines. This unit can be used as portable unit in a larger winery or as a fixed system supplying a glycol loop in a smaller winery. Unit is used for heating or cooling but cannot supply both at the same time. Manufactured by Kreyer, the World's leading producers of wine-cooling equipment. Uses: Cooling of must for cold soaks, slow starting ferments Heating up must after a cold soak period Cold Stabilization of tartaric crystals Controlling fermenting temperatures through cooling or heating Maintaining storage temperatures in tanks/barrels Check out these features: Cools or Heats 3 Tons (36,000btu) of cooling power (larger Chilly Max's are available) .85 Tons of heating power Can cool glycol/water bath down to -10C/14F or up to 42C/107F 208v 60Hz 3 phase supply voltage drawing 19.3 amps Rolls on four locking casters Sheet metal housing, electrolytic galvanized high surface quality, powder-coated and abrasion-resistant casing 7 Gallon Insulated Plastic glycol/water reservoir Easy to fill from outside Evaporator coil made of stainless steel High-quality Grundfos recirculation pump Built in pressure switch shuts down recirculation pump when not needed Digital Thermostat Lifting/Crane Hooks for transport All panels remove for easy access All units pass multiple tests prior to shipment German Engineering Controlled by compact PC boards with a temperature accuracy up to 0.1 degree Celsius. 33"L x 25"W x 31.5"T Unit has 1" Male BSP w/ 3/4" Female BSP inlet / outlet 6 Month Electrical Warranty 1 Year Mechanical Warranty CE Certified Please Note: This unit REQUIRES 208 v Three Phase power and will not function on anything else. Please confirm that you have the proper power for this unit before purchasing, and plan to have a qualified electrician wire the necessary plug to the cord. Available in larger sizes. For additional product options View the resource.
Due to high demand, this item is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this to you when we receive more inventory. Cooling & heating in one premium quality unit Control fermentation temperatures, cold-stabilize insulated tanks, or heat tanks during cold weather Fill from the exterior without the need to remove covers or panels Program and monitor temperatures via the digital controller Non-Return Kit installed as standard to prevent backflow when positioned below your tank jacket, heat exchanger, or piping system Four locking casters offer ease-of-mobility when moving the unit around the winery 3 Ton / 36,000 Btu cooling capacity 230V, 3 Phase power Made in Germany by Kreyer Cooling and Heating in one unit! Every Winemaker can appreciate the benefits of precise temperature control during all stages of production. This mobile unit allows you to easily control your ferment temperatures, heat your tanks during winter to expedite Malo-Lactic fermentation, or cold-stabilize your white wines. This unit can be used as portable unit in a larger winery or as a fixed system supplying a glycol loop in a smaller winery. Unit is used for heating or cooling but cannot supply both at the same time. Manufactured by Kreyer, the World's leading producers of wine-cooling equipment. Note: This unit runs off 230V 3 phase power. It will not run off 208V. Uses: Cooling of must for cold soaks, slow starting ferments Heating up must after a cold soak period Cold Stabilization of tartaric crystals Controlling fermenting temperatures through cooling or heating Maintaining storage temperatures in tanks/barrels Check out these features: Cools or Heats 3 Tons (36,000btu) of cooling power (larger Chilly Max's are available) .85 Tons of heating power Can cool glycol/water bath down to -10C/14F or up to 42C/107F 230v 60Hz 3 phase supply voltage drawing 19.3 amps Rolls on four locking casters Sheet metal housing, electrolytic galvanized high surface quality, powder-coated and abrasion-resistant casing 7 Gallon Insulated Plastic glycol/water reservoir Easy to fill from outside Evaporator coil made of stainless steel High-quality Grundfos recirculation pump Built in pressure switch shuts down recirculation pump when not needed Digital Thermostat Lifting/Crane Hooks for transport All panels remove for easy access All units pass multiple tests prior to shipment German Engineering Controlled by compact PC boards with a temperature accuracy up to 0.1 degree Celsius. 33"L x 25"W x 31.5"T Unit has 1" Male BSP w/ 3/4" Female BSP inlet / outlet 6 Month Electrical Warranty 1 Year Mechanical Warranty CE Certified Please Note: This unit REQUIRES 230 v Three Phase power and will not function on anything else. Please confirm that you have the proper power for this unit before purchasing, and plan to have a qualified electrician wire the necessary plug to the cord. Available in larger sizes. For additional product options View the resource.
Due to high demand, this item is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this item to you when we receive more inventory.
Cooling & heating in one premium quality unit
Control fermentation temperatures, cold-stabilize insulated tanks, or heat tanks during cold weather
Fill from the exterior without the need to remove covers or panels
Program and monitor temperatures via the digital controller
Non-Return Kit installed as standard to prevent backflow when positioned below your tank jacket, heat exchanger, or piping system
Four locking casters offer ease-of-mobility when moving the unit around the winery
3 Ton / 36,000 Btu cooling capacity
230V, Single Phase power
Made in Germany by Kreyer
Cooling and Heating in one unit!
Every Winemaker can appreciate the benefits of precise temperature control during all stages of production. This mobile unit allows you to easily control your ferment temperatures, heat your tanks during winter to expedite Malo-Lactic fermentation, or cold-stabilize your white wines. This unit can be used as portable unit in a larger winery or as a fixed system supplying a glycol loop in a smaller winery. Unit is used for heating or cooling but cannot supply both at the same time.
Manufactured by Kreyer, the World's leading producers of wine-cooling equipment.
Note: This unit runs off 230V single phase power. It will not run off 208V.
Uses:
Cooling of must for cold soaks, slow starting ferments
Heating up must after a cold soak period
Cold Stabilization of tartaric crystals
Controlling fermenting temperatures through cooling or heating
Maintaining storage temperatures in tanks/barrels
Check out these features:
Cools or Heats
3 Tons (36,000btu) of cooling power (larger Chilly Max's are available)
.85 Tons of heating power
Can cool glycol/water bath down to -10C/14F or up to 42C/107F
230 v Single Phase Power Supply Required
Rolls on four locking casters
Sheet metal housing, electrolytic galvanized high surface quality, powder-coated and abrasion-resistant casing
7 Gallon Insulated Plastic glycol/water reservoir
Easy to fill from outside
Evaporator coil made of stainless steel
High-quality Grundfos recirculation pump
Built in pressure switch shuts down recirculation pump when not needed
Digital Thermostat
Lifting/Crane Hooks for transport
All panels remove for easy access
All units pass multiple tests prior to shipment
German Engineering
Controlled by compact PC boards with a temperature accuracy up to 0.1 degree Celsius.
33"L x 25"W x 31.5"T
Unit has 1" Male BSP w/ 3/4" Female BSP inlet / outlet
6 Month Electrical Warranty
1 Year Mechanical Warranty
CE Certified
Please Note: This unit REQUIRES 230 v Single Phase power and will not function on anything else. Please confirm that you have the proper power for this unit before purchasing, and plan to have a qualified electrician wire the necessary plug to the cord.
Available in larger sizes. For additional product options View the resource.
These Fan Control Kits contain the necessary hardware to upgrade your Kreyer MR210 to a temperature controlled unit. Without this system, your fan would constantly be on, cooling the room beyond your desired temperature. This system combines a temperature controller with a Solenoid valve, so that you can set a specific temperature for the room, which will be maintained automatically.
Includes:
1/2" Solenoid Valve
Filter for 1/2" Solenoid Valve
Tubing & hardware to connect fan unit to Solenoid Valve
Solenoid/Temperature Controller Connection Cable
Single Fan Temperature Controller
Plumbers Tape
This system assumes you already have a glycol chiller and fan unit, as well as all the plumbing. You will still need an electrician to complete the wiring of your system.
These Fan Control Kits contain the necessary hardware to upgrade your Kreyer MR75 or MR135 to a temperature controlled unit. Without this system, your fan would constantly be on, cooling the room beyond your desired temperature. This system combines a temperature controller with a Solenoid valve, so that you can set a specific temperature for the room, which will be maintained automatically.
Includes:
1/2" Solenoid Valve
Filter for 1/2" Solenoid Valve
Tubing & hardware to connect fan unit to Solenoid Valve
Solenoid/Temperature Controller Connection Cable
Single Fan Temperature Controller
Plumbers Tape
This system assumes you already have a glycol chiller and fan unit, as well as all the plumbing. You will still need an electrician to complete the wiring of your system.
These Fan Control Kits contain the necessary hardware to upgrade your Kreyer SDS35L or SDS73L to a temperature controlled unit. Without this system, your fan would constantly be on, cooling the room beyond your desired temperature. This system combines a temperature controller with a Solenoid valve, so that you can set a specific temperature for the room, which will be maintained automatically.
Includes:
3/4" Solenoid Valve
Filter for 3/4" Solenoid Valve
Solenoid/Temperature Controller Connection Cable
Single Fan Temperature Controller
Plumbers Tape
This system assumes you already have a glycol chiller and fan unit, as well as all the plumbing. You will still need an electrician to complete the wiring of your system.
Use this Solenoid valve to control glycol flow into a fan unit. These Solenoids should be combined with a Fan Temperature Controller and Connection Cable to set a specific temperature for your fan unit to achieve in your room.
We recommend purchasing a Solenoid Filter with this valve. The filter will insure that no small particulates can get caught in the valve assembly, potentially damaging the unit.
230 v AC Solenoid with 1" FPT
We also sell complete control kits for Kreyer fan units:
MR75 & MR135 Control Kit
MR210 Control Kit
SD35L & SD73L Control Kit
Use this Solenoid valve to control glycol flow into a fan unit. These Solenoids should be combined with a Fan Temperature Controller and Connection Cable to set a specific temperature for your fan unit to achieve in your room.
This is a 1/2 in. FPT threaded piece for MR210 Fan Units. It can also be used with MR75 & 135 units with a 3/8" barb adapter.
We recommend purchasing a Solenoid Filter with this valve. The filter will ensure that no small particulates can get caught in the valve assembly, potentially damaging the unit.
230 v AC Solenoid with 1/2" FPT
We also sell complete control kits for Kreyer fan units:
MR75 & MR135 Control Kit
MR210 Control Kit
SD35L & SD73L Control Kit
Use this Solenoid valve to control glycol flow into a fan unit. These Solenoids should be combined with a Fan Temperature Controller and Connection Cable to set a specific temperature for your fan unit to achieve in your room.
This is a 3/4 in. FPT threaded piece for SD35L & SD73L Fan Units. It can also be used with other 1" SD fans if an adapter is used.
We recommend purchasing a Solenoid Filter with this valve. The filter will ensure that no small particulates can get caught in the valve assembly, potentially damaging the unit.
230 v AC Solenoid with 3/4" FPT
We also sell complete control kits for Kreyer fan units:
MR75 & MR135 Control Kit
MR210 Control Kit
SD35L & SD73L Control Kit
This temperature control unit controls room/cooler/cave/cellar temperature when used in conjunction with a Kreyer fan unit. Kreyer fan units are plumbed to a Kreyer Glycol cooling unit. This unit turns on and off an optional solenoid placed at the inlet of the fan unit, which allows chilled glycol to enter the coils on the fan unit, while also turning on the fan(s) that blow cold air out into the room. Requires a fan unit, solenoid valve, & connection cable to function. Fan unit must be plumbed to a glycol machine. For a fan unit temperature controller to be used below freezing temperatures, see our GLY950.
Use your existing glycol system to cool your cellar Eliminates the need to purchase an entirely separate refrigeration system MR series fan units offer quieter operation compared to the SD-S units Sized for well-insulated rooms up to 3,500 ft³ Made in Germany by Kreyer Cool your cellar using your existing glycol system. Save energy and money! These units work under the same principles as standard refrigeration but use cooled glycol instead of cooled refrigerant gas, eliminating the need to have a separate refrigeration system. It is a fantastic use of your glycol system for a majority of the year when typically glycol systems are on but are being sporadically called upon. Glycol systems do need to be sized to accommodate both these fan units and peak duty during the crush to be able to accommodate all tasks at once. Glycol from your main glycol chiller is recirculated through these fan units. Aluminum fins act as heat exchangers drawing heat out of your room as the fins are cooled by the glycol. If you have a Kreyer chiller/heater you can even heat a space in cold weather environments. The heat exchangers inside the units are made from corrugated aluminum fins and internally grooved copper tubes. The white ABS casing looks great. Because of its rounded corners it has no water retaining areas favorable to germ development. Units are outfitted with stainless steel screws and show no sharp, cutting edges. Fan Unit Temp Control Upgrades: 1/2 in. Solenoid Valve - Allows or blocks flow of glycol through the fan unit. Needs to be connected to a Controller to function. A filter is recommended to protect the solenoid. 1/2 in. Solenoid Filter- protects the solenoid valve from any particulate or sediment. Glycol Fan Control Unit - Set a specific temperature on this controller and it will open and close the solenoid valve. Solenoid Connection Cable - This 2 meter long cable is required to connect the Solenoid Valve & Control unit. Specifications of MR135: Will cool well insulated spaces up to 3500 cubic feet while drawing 2/3 Ton of cooling power Double Fan Unit (pictured is 3 fan unit) 220V connection required to run fan You will need to connect to your existing glycol system Inlet and Outlet 3/4" Male BSP
Use your existing glycol system to cool your cellar Eliminates the need to purchase an entirely separate refrigeration system MR series fan units offer quieter operation compared to the SD-S units Sized for well-insulated rooms up to 8,750 ft³ Made in Germany by Kreyer Cool your cellar using your existing glycol system. Save energy and money! These units work under the same principles as standard refrigeration but use cooled glycol instead of cooled refrigerant gas, eliminating the need to have a separate refrigeration system. It is a fantastic use of your glycol system for a majority of the year when typically glycol systems are on but are being sporadically called upon. Glycol systems do need to be sized to accommodate both these fan units and peak duty during the crush to be able to accommodate all tasks at once. Glycol from your main glycol chiller is recirculated through these fan units. Aluminum fins act as heat exchangers drawing heat out of your room as the fins are cooled by the glycol. If you have a Kreyer chiller/heater you can even heat a space in cold weather environments. The heat exchangers inside the units are made from corrugated aluminum fins and internally grooved copper tubes. The white ABS casing looks great. Because of its rounded corners it has no water retaining areas favorable to germ development. Units are outfitted with stainless steel screws and show no sharp, cutting edges. Fan Unit Temp Control Upgrades: 1/2 in. Solenoid Valve - Allows or blocks flow of glycol through the fan unit. Needs to be connected to a Controller to function. A filter is recommended to protect the solenoid. 1/2 in. Solenoid Filter- protects the solenoid valve from any particulate or sediment. Glycol Fan Control Unit - Set a specific temperature on this controller and it will open and close the solenoid valve. Solenoid Connection Cable - This 2 meter long cable is required to connect the Solenoid Valve & Control unit. Specifications of MR210: Will cool well insulated spaces up to 8750 cubic feet while drawing 1 Ton of cooling power Triple Fan Unit 220V connection required to run fan You will need to connect to your existing glycol system Inlet and Outlet: 3/4" Male BSP
Use your existing glycol system to cool your cellar Eliminates the need to purchase an entirely separate refrigeration system MR series fan units offer quieter operation compared to the SD-S units Sized for well-insulated rooms up to 8,750 ft³ Made in Germany by Kreyer Cool your cellar using your existing glycol system. Save energy and money! These units work under the same principles as standard refrigeration but use cooled glycol instead of cooled refrigerant gas, eliminating the need to have a separate refrigeration system. It is a fantastic use of your glycol system for a majority of the year when typically glycol systems are on but are being sporadically called upon. Glycol systems do need to be sized to accommodate both these fan units and peak duty during the crush to be able to accommodate all tasks at once. Glycol from your main glycol chiller is recirculated through these fan units. Aluminum fins act as heat exchangers drawing heat out of your room as the fins are cooled by the glycol. If you have a Kreyer chiller/heater you can even heat a space in cold weather environments. The heat exchangers inside the units are made from corrugated aluminum fins and internally grooved copper tubes. The white ABS casing looks great. Because of its rounded corners it has no water retaining areas favorable to germ development. Units are outfitted with stainless steel screws and show no sharp, cutting edges. Fan Unit Temp Control Upgrades: 1/2 in. Solenoid Valve - Allows or blocks flow of glycol through the fan unit. Needs to be connected to a Controller to function. A filter is recommended to protect the solenoid. 1/2 in. Solenoid Filter- protects the solenoid valve from any particulate or sediment. Glycol Fan Control Unit - Set a specific temperature on this controller and it will open and close the solenoid valve. Solenoid Connection Cable - This 2 meter long cable is required to connect the Solenoid Valve & Control unit. Specifications of MR210: Will cool well insulated spaces up to 8750 cubic feet while drawing 1 Ton of cooling power Triple Fan Unit 220V connection required to run fan You will need to connect to your existing glycol system Inlet and Outlet: 3/4" Male BSP
Use your existing glycol system to cool your cellar Eliminates the need to purchase an entirely separate refrigeration system MR series fan units offer quieter operation compared to the SD-S units Sized for well-insulated rooms up to 1,750 ft³ Made in Germany by Kreyer Cool your cellar using your existing glycol system. Save energy and money! These units work under the same principles as standard refrigeration but use cooled glycol that you already have instead of cooled refrigerant gas, eliminating the need to have a separate refrigeration system. It is a fantastic use of your glycol system for a majority of the year when typically glycol systems are on but are being sporadically called upon. Glycol systems do need to be sized to accommodate both these fan units and peak duty during the crush to be able to accommodate all tasks at once. Glycol from your main glycol chiller is recirculated through these fan units. Aluminum fins act as heat exchangers drawing heat out of your room as the fins are cooled by the glycol. If you have a Kreyer chiller/heater you can even heat a space in cold weather environments. The heat exchangers inside the units are made from corrugated aluminum fins and internally grooved copper tubes. The white ABS casing looks great. Because of its rounded corners it has no water retaining areas favorable to germ development. Units are outfitted with stainless steel screws and show no sharp, cutting edges. The MR series is quieter than the SD series but not as robust in construction. Fan Unit Temp Control Upgrades: 1/2 in. Solenoid Valve - Allows or blocks flow of glycol through the fan unit. Needs to be connected to a Controller to function. A filter is recommended to protect the solenoid. 1/2 in. Solenoid Filter- protects the solenoid valve from any particulate or sediment. Glycol Fan Control Unit - Set a specific temperature on this controller and it will open and close the solenoid valve. Solenoid Connection Cable - This 2 meter long cable is required to connect the Solenoid Valve & Control unit. Specifications of MR75: Will cool well insulated spaces up to 1750 cubic feet while drawing 1/3 Ton of cooling power Single Fan Unit (pictured is 3 fan unit) 220V connection required to run fan You will need to connect to your existing glycol system Inlet and Outlet: 3/8" OD bare copper pipe
Use your existing glycol system to cool your cellar Eliminates the need to purchase an entirely separate refrigeration system SD-S series fan units were designed specifically for high-moisture environments like wine cellars Sized for well-insulated rooms up to 52,500 ft³ Made in Germany by Kreyer Cool your cellar using your existing glycol system. Save energy and money! These units work under the same principles as standard refrigeration but use cooled glycol that you already have instead of cooled refrigerant gas, eliminating the need to have a separate refrigeration system. It is a fantastic use of your glycol system for a majority of the year when typically glycol systems are on but are being sporadically called upon. Glycol systems do need to be sized to accommodate both these fan units and peak duty during the crush to be able to accommodate all tasks at once. Glycol from your main glycol chiller is recirculated through these fan units. Aluminum fins act as heat exchangers drawing heat out of your room as the fins are cooled by the glycol. If you have a Kreyer chiller/heater you can even heat a space in cold weather environments. The heat exchangers inside the units are made from corrugated aluminum fins and internally grooved copper tubes. The white ABS casing looks great. Because of its rounded corners it has no water retaining areas favorable to germ development. Both series are fitted with stainless steel screws and show no sharp, cutting edges. Built in defrosters help ensure the system is working at optimum efficiency The SD-S series has been designed especially for problematic environments such as wine-cellars with high moisture. The high-performance fans on the SD-S unit are lubricated for life. Fan Unit Temp Control Upgrades: 1 in. Solenoid Valve - Allows or blocks flow of glycol through the fan unit. Needs to be connected to a Controller to function. A filter is recommended to protect the solenoid. 1 in. Solenoid Filter- protects the solenoid valve from any particulate or sediment. Glycol Fan Control Unit - Set a specific temperature on this controller and it will open and close the solenoid valve. Solenoid Connection Cable - This 2 meter long cable is required to connect the Solenoid Valve & Control unit. Inlet and Outlet: 1" Male BSP The SD-S 110 is sized to: Cool a room up to 52,500 when the ceiling and walls are very well insulated, using approximately 3.75 tons of cooling power from your chilling system. If the room is half insulated you will two SD-S 110's and more power to cool a room this size. Please be sure to consult with our Wine Team for the proper sizing. The SD-S 110 features 3 fans.
Use your existing glycol system to cool your cellar Eliminates the need to purchase an entirely separate refrigeration system SD-S series fan units were designed specifically for high-moisture environments like wine cellars Sized for well-insulated rooms up to 85,000 ft³ Made in Germany by Kreyer Cool your cellar using your existing glycol system. Save energy and money! These units work under the same principles as standard refrigeration but use cooled glycol that you already have instead of cooled refrigerant gas, eliminating the need to have a separate refrigeration system. It is a fantastic use of your glycol system for a majority of the year when typically glycol systems are on but are being sporadically called upon. Glycol systems do need to be sized to accommodate both these fan units and peak duty during the crush to be able to accommodate all tasks at once. Glycol from your main glycol chiller is recirculated through these fan units. Aluminum fins act as heat exchangers drawing heat out of your room as the fins are cooled by the glycol. If you have a Kreyer chiller/heater you can even heat a space in cold weather environments. The heat exchangers inside the units are made from corrugated aluminum fins and internally grooved copper tubes. The white ABS casing looks great. Because of its rounded corners it has no water retaining areas favorable to germ development. Both series are fitted with stainless steel screws and show no sharp, cutting edges. Built in defrosters help ensure the system is working at optimum efficiency The SD-S series has been designed especially for problematic environments such as wine-cellars with high moisture. The high-performance fans on the SD-S unit are lubricated for life. Fan Unit Temp Control Upgrades: 1 in. Solenoid Valve - Allows or blocks flow of glycol through the fan unit. Needs to be connected to a Controller to function. A filter is recommended to protect the solenoid. 1 in. Solenoid Filter- protects the solenoid valve from any particulate or sediment. Glycol Fan Control Unit - Set a specific temperature on this controller and it will open and close the solenoid valve. Solenoid Connection Cable - This 2 meter long cable is required to connect the Solenoid Valve & Control unit. Inlet and Outlet: 1" Male BSP The SD-S 148 is sized to: Cool a room up to 85,000 cubic feet when the ceiling and walls are well insulated. Will use approximately 5.5 tons of cooling power from your chilling system. Please be sure to consult with our Wine team for proper sizing of a fan unit. This unit features 4 fans. Product Statistics Weight: 150lbs Dimensions: 82"L x 12"W x 18"H
Use your existing glycol system to cool your cellar Eliminates the need to purchase an entirely separate refrigeration system SD-S series fan units were designed specifically for high-moisture environments like wine cellars Sized for well-insulated rooms up to 17,500 ft³ Made in Germany by Kreyer Cool your cellar using your existing glycol system. Save energy and money! These units work under the same principles as standard refrigeration but use cooled glycol that you already have instead of cooled refrigerant gas, eliminating the need to have a separate refrigeration system. It is a fantastic use of your glycol system for a majority of the year when typically glycol systems are on but are being sporadically called upon. Glycol systems do need to be sized to accommodate both these fan units and peak duty during the crush to be able to accommodate all tasks at once. Glycol from your main glycol chiller is recirculated through these fan units. Aluminum fins act as heat exchangers drawing heat out of your room as the fins are cooled by the glycol. If you have a Kreyer chiller/heater you can even heat a space in cold weather environments. The heat exchangers inside the units are made from corrugated aluminum fins and internally grooved copper tubes. The white ABS casing looks great. Because of its rounded corners it has no water retaining areas favorable to germ development. Both series are fitted with stainless steel screws and show no sharp, cutting edges. The SD-S series has been designed especially for problematic environments such as wine-cellars with high moisture. The high-performance fans on the SD-S unit are lubricated for life. The SD-S 35 is sized to: Cool a room up to 17,500 when the ceiling and walls are well insulated. Cooling a room this size from 90F to 60F will use approximately 1.05 tons of cooling power from your chilling system. If the room is half insulated you will need approximately 50% more power or 1.6 tons of cooling power. Once you've achieved the desired temperature it takes considerably less power to maintain it. Fan Unit Temp Control Upgrades: 3/4 in. Solenoid Valve - Allows or blocks flow of glycol through the fan unit. Needs to be connected to a Controller to function. A filter is recommended to protect the solenoid. 3/4 in. Solenoid Filter- protects the solenoid valve from any particulate or sediment. Glycol Fan Control Unit - Set a specific temperature on this controller and it will open and close the solenoid valve. Solenoid Connection Cable - This 2 meter long cable is required to connect the Solenoid Valve & Control unit. Inlet and Outlet: 3/4" Male BSP Please Note: This unit only has one fan. The weight shown below is for shipping purposes, as this item ships at an oversize rate with UPS Ground. Actual weight of the fan is about 35lb. Actual Dimensions are 710x410x460mm
Use your existing glycol system to cool your cellar Eliminates the need to purchase an entirely separate refrigeration system SD-S series fan units were designed specifically high-moisture environments like wine cellars Sized for well-insulated rooms up to 28,000 ft³ Made in Germany by Kreyer Good for cooling cellars up to 28,000 cubic feet Cool your cellar using your existing glycol system. Save energy and money! These units work under the same principles as standard refrigeration but use cooled glycol that you already have instead of cooled refrigerant gas, eliminating the need to have a separate refrigeration system. It is a fantastic use of your glycol system for a majority of the year when typically glycol systems are on but are being sporadically called upon. Glycol systems do need to be sized to accommodate both these fan units and peak duty during the crush to be able to accommodate all tasks at once. Glycol from your main glycol chiller is recirculated through these fan units. Aluminum fins act as heat exchangers drawing heat out of your room as the fins are cooled by the glycol. If you have a Kreyer chiller/heater you can even heat a space in cold weather environments. The heat exchangers inside the units are made from corrugated aluminum fins and internally grooved copper tubes. The white ABS casing looks great. Because of its rounded corners it has no water retaining areas favorable to germ development. Both series are fitted with stainless steel screws and show no sharp, cutting edges. Built in defrosters help ensure the system is working at optimum efficiency The SD-S series has been designed especially for problematic environments such as wine-cellars with high moisture. The high-performance fans on the SD-S unit are lubricated for life. Fan Unit Temp Control Upgrades: 3/4 in. Solenoid Valve - Allows or blocks flow of glycol through the fan unit. Needs to be connected to a Controller to function. A filter is recommended to protect the solenoid. 3/4 in. Solenoid Filter- protects the solenoid valve from any particulate or sediment. Glycol Fan Control Unit - Set a specific temperature on this controller and it will open and close the solenoid valve. Solenoid Connection Cable - This 2 meter long cable is required to connect the Solenoid Valve & Control unit. Inlet and Outlet: 3/4" Male BSP The SD-S 73 is sized to: Cool a room up to 28,000 cubic feet when the ceiling and walls are well insulated. Will use approximately 2.5 tons of cooling power from your chilling system. If the room is half insulated you will need to move up to SD-S 110. Please be sure to consult with our Wine team for proper sizing of a fan unit.
Rolling casters compatible with the Kreyer MiniChilly 05/09/17. Direct replacements to the rolling casters included on the MB MiniChillys (GLY405 / GLY406).
Set of 4 wheels with mounting screws included.
Use:
The most versatile cooling and heating tool a winery can own
Pump must or wine throught the machine | Heats or cools inline
The only practical solution for cooling or heating crushed grapes
2" ID stainless steel tube-in-tube heat exchanger allows crushed grapes to pass through
Use your choice of pumps to move product through SR chiller/heater
Made in Germany | Used for over 40 years in French and German wineries
Features:
Plenty of Power | 11.7 Tons (140,400btu) of Cooling power
Wide Temperature Range | 28F or up to 113F
Moves Where You Need It | Rolls on four locking casters
Control Temperatures with Ease | Digital Thermostat
Top Class Components
The most versatile cooling and heating tool a winery can own. Whether you want to cool crushed grapes to cold soak temperatures, heat a sluggish ferment, heat a tank for ML without having a dedicated hot water loop, or cold stabilize a tank quickly, the SR is an extremely useful machine. It often eliminates the need for a separate heating loop in your winery. It is loved for quickly doing cold stabilization on one tank at a time. It is more effective at cooling crushed grapes than trying to cool in a tank. Because it is a closed system it can be used with sparkling wine or cider without losing carbonation.
Most wineries who use an SR for cooling/heating specific tanks or vats also have a dedicated main chiller connected to their permanent cooling loop. However the SR can also act as the back up chiller in case your main chiller goes down. You can use the SR to chill a tank, such as a large HDPE tank. Connect that tank to your glycol loop and if your main chiller goes down you already have a backup plan in place.
Made in Germany, thousands of Kreyer SR chillers have been in use for over 40 years in France and Germany.
The SR is not like a regular glycol chiller where a cooled bath is pumped into the tank jackets. The SR features a large, tubular heat-exchanger that is completely insulated. Your product is pumped through the inner tube while heat or cold travels the opposite direction through the outer tube. The top half of the SR houses the compressor for cooling while heating is performed in the Heat-Pump operation mode. The SR is uniquely designed unit for changing the temperature inline of crushed grapes, wine, sparkling wine, water, cider, fruit juice and distillates.
By setting the temperature, you can rely on the SR to maintain tank temperature for as long as needed, in either heating or cooling mode.
The case of the unit as well as all parts that come in contact with the treated medium are made of stainless steel. The ventilation grills are lacquered in black. Due to its four wheels, this SR unit is easy to maneuver. This allows the user to cool or to heat single tanks or other containers, as required. For example: starting a stopped fermentation by heating the tank content. Your choice of external pump is controlled by the SR’s control panel.
The cooling units of the SR series are available in seven different sizes. This is 11.7 Ton model. Smaller and larger machines are available for quote.
Applications:
Direct cooling or heating of must at the beginning of fermentation
Tartaric stabilization of wines
Warming up wine from storage to bottling temperature
Biological reduction of acids
Regulation of fermentation temperature
Cool storage of wine until bottling
Suitable for sparkling wine and carbonated beverages (closed loop with no carbonation loss)
Cooling of liquids with particles such as unfiltered juice
Air cooling of the cellar in combination with additional equipment (thermo-fans and accessories)
Check out these features:
Cools or Heats
11.7 Tons (140,400btu) of cooling power
Can maintain temps from 23F to 113F.
230V 60Hz 3 phase supply voltage drawing 40 amps
Mobile unit with 4 casters, two locking
Sheet metal housing, electrolytic galvanized high surface quality, powder-coated and abrasion-resistant casing
Control an external cellar pump from the SR's control panel
Evaporator coil made of stainless steel
Automatic control of the wine pump according to set temperature
Digital Thermostat
Lifting/Crane Hooks for transport
Panels remove for easy access
All units pass multiple tests prior to shipment
German Engineering
Controller display shows temperature accuracy up to 0.1 degree Celsius.
41.3"L x 41.3"W x 84.6"T
Empty Weight: 992 lbs
Unit has 2" tri-clamp inlet / outlet
6 Month Electrical Warranty
1 Year Mechanical Warranty
CE Certified
Please Note: This unit REQUIRES 230 v Three Phase power and will not function on anything else. Please confirm that you have the proper power for this unit before purchasing, and plan to have a qualified electrician wire the necessary plug to the cord.
Maximize Finished Yield: Reduces beer loss and waste by replacing bulky hop pellets with a highly concentrated liquid extract.
Intense Hop Aromatics: Delivers variety-specific, "survivable" hop compounds for a powerful aromatic boost in every batch.
Versatile Cold-Side Use: Designed for easy pouring into the fermenter during active or post-fermentation dry hopping and whirlpool additions.
Superior Efficiency: Streamlines logistics with a compact footprint and high replacement rates—up to 100:1 compared to T-90 pellets.
HyperBoost®, formerly YCH 701, is a concentrated hop oil extract produced through an innovative CO2 supercritical extraction process.
Intended to amplify hop aromatics and increase yield, HyperBoost excels at adding beautiful hop aroma anywhere pellets are normally used, including cold-side applications. HyperBoost is made from single-hop varieties to deliver variety-specific aroma boosts to your finished beer.
Chief Advantages:
Increased efficiency
Ease of use
Increased aroma
Less storage space needed
High concentrations of survivable compounds
Reduction of waste
How to Brew with HyperBoost?
HyperBoost® is designed to easily pour in your fermenter as a dry hop addition, adding an intense saturation of hop flavor to your finished beer. Most brewers choose to use HyperBoost during active fermentation, but it can also be added to the whirlpool. Using HyperBoost in place of traditional pellets can increase finished beer yield.
Kettle: HyperBoost is not intended for kettle additions. For early kettle and bittering additions, we recommend pellets or CO2 extract. DynaBoost® carries variety-specific oil and alpha acid content to the kettle and can be used as a late kettle addition.
Post-Boil / Whirlpool: For whirlpool use, brewers can replace up to 100% of pellets with HyperBoost. We suggest replacing T-90 pellet additions in the whirlpool at a rate of 50:1 by weight (20 g of HyperBoost to replace 1 kg T-90). Your brewery might choose to use more or less depending on beer style or overall goal.
Fermentation: HyperBoost can be used as an active or post-fermentation hop addition. Incorporate HyperBoost anywhere in the process you would typically use pellets.
Dry Hopping: For dry hop additions, YCH recommends using HyperBoost for 25-50% of the addition and adding T-90 or Cryo® pellets for the remainder of the hop charge. As a dry hop, we suggest starting with a replacement rate of 100:1 HyperBoost to T-90 pellets by weight (10 g HyperBoost in place of 1 kg T-90) to 125:1 (8 g HyperBoost in place of 1 kg T-90).
Krush™ is a trademark owned by Hop Breeding Company.
HyperBoost® is a registered trademark owned by Yakima Chief Hops, LLC.
With complex, ripe, and punchy aromas, this is a brewer favorite that shines in all styles of beer and hop combinations
Aroma Profile: Berry, Citrus, Stone Fruit, Tropical, Woody
Alpha Acids: 18.0 – 22.0%
Cryo Hop® Hop Pellets
Higher AA and nearly twice the resin content of traditional T-90 hop pellets
Increase yield by reducing vegetal matter in your brewhouse and fermenter
Cryo Hops® provide brewers with the ability to get gigantic hop character while reducing astringent and unpleasant vegetal flavors. With a substantially higher oil and resin content, LupuLN2 powder offers up all the flavor and aroma of a heavily hopped beer, but with a significanly reduced grassy character. Additionally, the lower dosage rate of the concentrated powder reduces the volume of trub and therefore, kettle loss. Using Cryo Hops® you will net more beer that is clearer!
Typical usage of Cryo Hops® would be roughly 50% of pellets. LupuLN2 powder can be used in any application where traditional hop products are utilized, including: Bittering, Kettle, Whirlpool and even direct to the fermentor. It is suggested that you use Cryo Hops® as late additions, in the whirlpool or dry hop, as the volatile aromatic compounds will be driven off if added early in the boil.
Cryo Hops® are an innovative hop product that is made by separating the lupulin from the hop flower using cryogenic processing. The result is a product with twice the potency of T90 pellets, with reduced astringency and vegetative material.
Note: These hops come pelletized. The powder is compressed into pellet form to make handling easier.
Typical Hop Statistics:
Alpha Acids: 18.0 – 22.0%
Beta Acids: 10.0 – 14.0%
Total Oil: 1.0 – 5.0%
Krush™ is a trademark owned by Hop Breeding Company.
Cryo Hops® is a registered trademark owned by Yakima Chief Hops, LLC.
Characterized by notes of citrus, specifically orange, alongside tropical hints of mango and guava
Performs well in a wide range of beer styles and hop combinations
Aroma Profile: Berry, Citrus, Stone Fruit, Tropical, Woody
Alpha Acids: 10.0 – 14.0%
T-90 Hop Pellets
Released by the Hop Breeding Company in 2024, Krush™ HBC 586 c.v. offers a complex and punchy aromatic profile. This hop variety is characterized by notes of citrus, specifically orange, alongside tropical hints of mango and guava. Stone fruit qualities, reminiscent of peach, are also present, complemented by berry notes described as mixed berry, and a woody, resinous undertone. These characteristics are evident both on the bine and in the finished beer. Described as a fruit cocktail in cone form, Krush™ is a highly unique and versatile hop that delivers significant impact. It has become a favorite among brewers and performs well in a wide range of beer styles and hop combinations.
Originally bred in 2007 by the Hop Breeding Company experimental hop variety program, Krush™ HBC 586 went through a thorough 17-year process as an experimental variety and was officially released as a commercial hop brand in 2024.
Hop Statistics
Alpha Acids: 10.0 – 14.0%
Beta Acids: 7.0 – 9.0%
Alpha-Beta Ratio: 1.1 – 2.0
Cohumulone: (% of alpha acids): 34 – 40%
Total Oil: 0.5 – 3.0%
Krush™ is a trademark owned by Hop Breeding Company.
Counter top inline keg dispenser that can serve ice cold beer from unchilled kegs Compact and portable. Use anywhere you have access to 110V power Superior cooling capacity. Chill up to 8 gallons of beer, inline, per hour! Fill the reservoir with tap water, or use a glycol solution for optimal performance NukaTap Flow Control Faucets, tap handles, and drip tray included Great for bars, restaurants that need to add capacity These style chillers are how beer is poured in most European cafes If you're looking for a home draft system, but don't have the space for a kegerator or keezer, we've got the answer! The KOMOS KRYO benchtop keg dispenser can serve ice cold beer from unchilled kegs. It's essentially an electric jockey box that chills beer inline as it passes from the keg through the internal draft coils that sit submerged in the glycol reservoir. Simply place it on your counter or benchtop, fill the reservoir with a 20% glycol solution, and hook up your keg to the draft shank bulkheads. In roughly an hour, the reservoir will have cooled down enough that you'll be ready to pour! And thanks to the compact size, the KRYO can easily be transported from your home to the next backyard BBQ, cabin trip, wedding, or virtually any gathering of thirsty people you can think of. For homebrewers this would allow you to keep your refrigerator at fermenation temperatures while always seving your beer ice cold. Glycol Reservoir Although you can fill the reservoir with water only, for optimal performance we highly recommend using a glycol/water mix so you can lower the chilling solution below freezing. You simply won't be able to get your beer as cold if using water only. The sight gauge at the front will let you know if it's time to top up the reservoir, but also functions as a drain. When it's time to move the KRYO from one location to another, drain out the glycol into a sealable container to avoid spills during transportation. The glycol reservoir provides an exceptional amount of cooling power that makes it perfect for servicing small bars or cafes, as well as home use. If you're deciding between this model and the KRYO Nomad, note that peak chilling capacity for this model is approximately 8 gallons per hour, whereas the Nomad can chill up to roughly 2 gallons per hour. NukaTap Flow Control Faucets These stainless steel forward sealing faucets allow you to make instant adjustments to the beverage flow as you pour. A perfect faucet for those who often switch between beer styles with different carbonation levels. No need to rebalance your lines or play with your regulator settings. Adjust the flow control level to dial in the flow rate and pour perfect pints every time! They also have the lowest thermal mass and best laminar flow design to further reduce foaming issues. Draft Shank Bulkheads The draft shank bulkheads with beer thread allow you to choose the type of fittings and draft line that best suits your needs. We highly recommend EVABarrier draft line and Duotight fittings—the same lines and fittings that come standard with our KOMOS Kegerators. These Duotight Female Beer Thread Adapters will allow you to hook up 8 mm OD EVABarrier, and also work with sanke keg couplers if you'll be dispensing commercial kegs. For homebrew kegs, we recommend Duotight Flare Adapters for your QDs, or if you're starting from scratch, consider the Duotight Ball Lock Quick Disconnects. Includes: (2) NukaTap Stainless Flow Control Faucets (2) Tap Handles Stainless Countertop Drip Tray w/ Removable Grill Features: Chill 8 gallons of beer per hour (based on 68°F ambient) Draft shank bulkheads compatible with Duotight fittings or nut & tailpiece combos STC-1000 temperature controller (reads in °C) Reservoir volume: 4.2 gal Voltage: 110V-120V Current: 0.9A Frequency: 60Hz Dimensions: 19" x 12" x 17.5" (not including faucets / drip tray) CE Certified Reservoir Temp Controller: Follow these steps to adjust the SET temperature on the controller. If using water only, be sure to keep the reservoir temp set at or above 2°C to avoid freezing. With a 20% glycol solution, you can set the temp as low as -2°C. The reservoir volume is 4.2 gallons, so you will only need to purchase 1 gallon of glycol to make a 20% mix. Hold the 'Up" button for 3 seconds until the number is flashing While the number is flashing, press the 'Down' button to decrease the set temperature or press the 'Up' button to increase the set temperature. Wait 3 seconds and the controller will save the setting and return to normal operation mode. Warning: Do not set the reservoir temperature controller lower than 28°F (-2ºC). Running the unit below this temperature may negatively affect the unit's efficiency and has the potential to freeze beer.
Counter top inline keg dispenser that can serve ice cold beer from unchilled kegs Compact and portable. Use anywhere you have access to 110V power Superior cooling capacity. Chill up to 8 gallons of beer, inline, per hour! Fill the reservoir with tap water, or use a glycol solution for optimal performance NukaTap Flow Control Faucets, tap handles, and drip tray included Great for bars, restaurants that need to add capacity These style chillers are how beer is poured in most European cafes If you're looking for a home draft system, but don't have the space for a kegerator or keezer, we've got the answer! The KOMOS KRYO benchtop keg dispenser can serve ice cold beer from unchilled kegs. It's essentially an electric jockey box that chills beer inline as it passes from the keg through the internal draft coils that sit submerged in the glycol reservoir. Simply place it on your counter or benchtop, fill the reservoir with a 20% glycol solution, and hook up your keg to the draft shank bulkheads. In roughly an hour, the reservoir will have cooled down enough that you'll be ready to pour! And thanks to the compact size, the KRYO can easily be transported from your home to the next backyard BBQ, cabin trip, wedding, or virtually any gathering of thirsty people you can think of. For homebrewers this would allow you to keep your refrigerator at fermenation temperatures while always seving your beer ice cold. Glycol Reservoir Although you can fill the reservoir with water only, for optimal performance we highly recommend using a glycol/water mix so you can lower the chilling solution below freezing. You simply won't be able to get your beer as cold if using water only. The sight gauge at the front will let you know if it's time to top up the reservoir, but also functions as a drain. When it's time to move the KRYO from one location to another, drain out the glycol into a sealable container to avoid spills during transportation. The glycol reservoir provides an exceptional amount of cooling power that makes it perfect for servicing small bars or cafes, as well as home use. If you're deciding between this model and the KRYO Nomad, note that peak chilling capacity for this model is approximately 8 gallons per hour, whereas the Nomad can chill up to roughly 2 gallons per hour. NukaTap Flow Control Faucets These stainless steel forward sealing faucets allow you to make instant adjustments to the beverage flow as you pour. A perfect faucet for those who often switch between beer styles with different carbonation levels. No need to rebalance your lines or play with your regulator settings. Adjust the flow control level to dial in the flow rate and pour perfect pints every time! They also have the lowest thermal mass and best laminar flow design to further reduce foaming issues. Draft Shank Bulkheads The draft shank bulkheads with beer thread allow you to choose the type of fittings and draft line that best suits your needs. We highly recommend EVABarrier draft line and Duotight fittings—the same lines and fittings that come standard with our KOMOS Kegerators. These Duotight Female Beer Thread Adapters will allow you to hook up 8 mm OD EVABarrier, and also work with sanke keg couplers if you'll be dispensing commercial kegs. For homebrew kegs, we recommend Duotight Flare Adapters for your QDs, or if you're starting from scratch, consider the Duotight Ball Lock Quick Disconnects. Includes: (2) NukaTap Stainless Flow Control Faucets (2) Tap Handles Stainless Countertop Drip Tray w/ Removable Grill Features: Chill 8 gallons of beer per hour (based on 68°F ambient) Draft shank bulkheads compatible with Duotight fittings or nut & tailpiece combos STC-1000 temperature controller (reads in °C) Reservoir volume: 4.2 gal Voltage: 110V-120V Current: 0.9A Frequency: 60Hz Dimensions: 19" x 12" x 17.5" (not including faucets / drip tray) CE Certified Reservoir Temp Controller: Follow these steps to adjust the SET temperature on the controller. If using water only, be sure to keep the reservoir temp set at or above 2°C to avoid freezing. With a 20% glycol solution, you can set the temp as low as -2°C. The reservoir volume is 4.2 gallons, so you will only need to purchase 1 gallon of glycol to make a 20% mix. Hold the 'Up" button for 3 seconds until the number is flashing While the number is flashing, press the 'Down' button to decrease the set temperature or press the 'Up' button to increase the set temperature. Wait 3 seconds and the controller will save the setting and return to normal operation mode. Warning: Do not set the reservoir temperature controller lower than 28°F (-2ºC). Running the unit below this temperature may negatively affect the unit's efficiency and has the potential to freeze beer.
