Storage, packaging, and finishing tanks made for ambitious homebrewers and small breweries Cooling jacket welded to the vertical walls of the tank provide superior cooling capabilities compared to in-solution cooling coils Made from stainless steel throughout with Brewtools' proprietary PureBlast™ surface—no passivation required, simply rinse with warm water before your first use Pressure rated to 30 PSI so you can safely carbonate and pressure transfer finished beer to kegs with virtually no oxygen pickup All valves, fittings, and gaskets come included Brewtools Brite Tanks are storage, packaging, and finishing tanks made for ambitious homebrewers and small breweries. As part of the Brewtools identity, they've explored new techniques and solutions. This has resulted in a series of high-end tanks with new features and a lot of possibilities. Key Features: Brewtools PureBlast™ surface inside and out which eliminate the use of wax and polishing compounds and does not require passivation. Cooling jacket in the vertical walls offers efficient cooling without the hassle of cleaning a spiral. Many options for connecting accessories like sensors, carb. stones and other accessories. Pressure rated for 2 bar / 30 PSI. 8" TC port on top for easy access. 2" TC dump valve 3x 1.5" DN32 ports (1 on the back) + 1x TC34mm port for sample valve Brewtools Brite Tanks are designed and manufactured with special attention to safety and quality. They are tested and certified according to the requirements for PED 2014/68/EU by a third party. Specifications: Height without accessories: 39.3" Packaging size: 36.2" (h) x 19.6" (w) x 19.6 (d) Net weight: TBD Gross weight: TBD Tank diameter (inside): 15.7" Ø Gross volume: 21.3 gallons Max rec. volume: 19.8 gallons Min rec. volume: 5.2 gallons Material: 1.5mm stainless steel (SS304) Operating pressure: 1.0 bar / 15 PSI Max pressure: 2.0 bar / 30 PSI The tank comes with insulation jacket, stainless steel butterfly valve and the necessary piping and clamps/gaskets. For more detailed information and user manual, please visit docs.brewtools.com
Kit contains what you need to carbonate in Brewtools Unitanks using CO2 and a ball lock connector.
Contents:
Ball Lock Adapter, Gas, TC34mm
Carb. stone 4.7" (120 mm), 0.5 micron
Gaskets
M16 O2/CO2 stone holder for ball lock
3" CIP adapter with 1/2" MPT threads for CIP spray ball with or without extension pipe. This is the correct size for the Brewtools F40 and F80 Unitanks.
Fluid input is TC 34mm.
Remember 34mm Tri-Clamp and gasket are needed, and also the fitting of choice for connecting fluid input.
4" CIP adapter with 1/2" MPT threads for CIP spray ball with or without extension pipe. Used for CIP via the 4" port on Brewtools Steam Hats or the F150 Unitank.
Fluid input is TC 34mm.
Remember 34mm Tri-Clamp and gasket are needed, and also the fitting of choice for connecting fluid input.
CIP-ball for easy cleaning. Fits all Brewtools CIP adapters and center pipes with 1/2" NPT threads.
Does not include the adapter shown in the example photo.
Circulation manifold for mashing and sparging. Fastened around the sparge pipe and can be adjusted to sit at the top of the grain bed.
Included:
Manifold
Sparge adapter with 1/2" (12 mm) hose barb
Silicone core
Silicone tube 3/8" x 5/8", 3.2' (10mm x 16 mm, 1 meter)
Tri Clamp, 34mm
Circulation manifold for mashing and sparging. Fastened around the sparge pipe and can be adjusted to sit at the top of the grain bed.
Included:
Manifold
Sparge adapter with 1/2" (12 mm) hose barb
Silicone core
Silicone tube 3/8" x 5/8", 3.2' (10mm x 16 mm, 1 meter)
Tri Clamp, 34mm
Circulation manifold for mashing and sparging. Fastened around the sparge pipe and can be adjusted to sit at the top of the grain bed.
Included:
Manifold
Sparge adapter with 1/2" (12 mm) hose barb
Silicone core
Silicone tube 3/8" x 5/8", 3.2' (10mm x 16 mm, 1 meter)
Tri Clamp, 34mm
Ferment, cold crash, and carbonate beer all in one vessel with the Brewtools F-Series Unitank Cooling jacket welded to the vertical walls of the tank provide superior cooling capabilities compared to in-solution cooling coils Made from stainless steel throughout with Brewtools' proprietary PureBlast™ surface—no passivation required, simply rinse with warm water before your first use Pressure rated to 30 PSI so you can safely ferment under pressure and pressure transfer finished beer to kegs with virtually no oxygen pickup Brewtools is a Norwegian brand known for high-quality products made without compromise. From brewing systems to fermenters, they continue to push the envelope of innovation for homebrewers around the globe All valves, fittings, and gaskets come included Brewtools Unitanks are fermenters made for ambitious homebrewers and small breweries. As part of the Brewtools identity, they've explored new techniques and solutions. This has resulted in a series of high end fermentation tanks with new features and a lot of possibilities. Key Features: Brewtools PureBlast™ surface inside and out which eliminate the use of wax and polishing compounds and does not require passivation. Cooling jacket in the vertical walls offers efficient cooling without the hassle of cleaning a spiral. Many options for connecting accessories like sensors, heaters, carb. stones and other accessories. Pressure rated for 2 bar / 30 PSI Cooling jacket pressure rated for 0.5 bar / 7 PSI 8" TC port on top for easy access. 2" TC dump and racking valves. BrewTools Unitanks are designed and manufactured with special attention to safety and quality. They are tested and certified according to the requirements for PED 2014/68/EU by a third party. Specifications: Low height w/o acc.: 50" Max height w/o acc.: 57.9" Packaging size: 51.2" (h) x 23.6" (w) x 23.6" (d) Net weight: 123.5 lbs Gross weight: 136.5 lbs Tank diameter (inside): Ø19.7" Gross volume: 41.7 gal Max rec. volume: 40 gal Min rec. volume: 10.5 gal Volume, cone: 6.3 gal Material: 1.5mm stainless steel (SS304) Operating pressure: 1.0 bar / 15 PSI Max pressure: 2.0 bar / 30 PSI In the box: Unitank with adjustable frame 1 pcs Analog pressure gauge, TC34mm 2 pcs Butterfly-valve, 2" 1 pcs Butterfly-valve, 34mm DN20 1 pcs Blow-off pipe 1 pcs Racking arm 2" 1 pcs TC elbow 90°, 2" 1 pcs Insulation jacket, black neoprene 1 pcs Sample valve, 34mm 1 pcs TC Adapter 8"-4" 1 pcs TC blind cap, 4" 1 pcs TC blind cap 2" 2 pcs TC blind cap 1.5" 3 pcs TC blind cap 34mm 2 pcs TC gasket 8" lipped 2 pcs TC gasket 4" 2 pcs TC gasket 2" 5-pack 1 pcs TC gasket 1.5" 5-pack 3 pcs TC gasket 34mm 5-pack (DN20) 1 pcs Tri Clamp 8" 1 pcs Tri Clamp 4" 5 pcs Tri Clamp 2" 2 pcs Tri Clamp 1.5" 10 pcs Tri Clamp 34mm 1 pcs TC tool 4 pcs M10 steel/rubber feet 1 pcs TC34mm safety valve (PRV, 2 bar) Necessary bolts and parts for assembly 5 year manufacturer's warranty
Recommended accessories include: HopDrop-kit, Thermowells for your sensors, 34mm Ball-Lock gas adapter for CO2 filling, Coil for sample valve, Spunding valve, Hose barbs for filling and dumping, etc. For User Manuals and support, please follow this link to Brewtools Docs. NOTE: Model in photo is a prototype. Minor changes and improvements may occur.
Ferment, cold crash, and carbonate beer all in one vessel with the Brewtools F-Series Unitank Cooling jacket welded to the vertical walls of the tank provide superior cooling capabilities compared to in-solution cooling coils Made from stainless steel throughout with Brewtools' proprietary PureBlast™ surface—no passivation required, simply rinse with warm water before your first use Pressure rated to 30 PSI so you can safely ferment under pressure and pressure transfer finished beer to kegs with virtually no oxygen pickup Brewtools is a Norwegian brand known for high-quality products made without compromise. From brewing systems to fermenters, they continue to push the envelope of innovation for homebrewers around the globe All valves, fittings, and gaskets come included Brewtools Unitanks are fermenters made for ambitious homebrewers and small breweries. As part of the Brewtools identity, they've explored new techniques and solutions. This has resulted in a series of high end fermentation tanks with new features and a lot of possibilities. Key Features: Brewtools PureBlast™ surface inside and out which eliminate the use of wax and polishing compounds and does not require passivation. Cooling jacket in the vertical walls offers efficient cooling without the hassle of cleaning a spiral. Many options for connecting accessories like sensors, heaters, carb. stones and other accessories. Pressure rated for 2 bar / 30 PSI Cooling jacket pressure rated for 0.5 bar / 7 PSI 8" TC port on top for easy access. 2" TC dump and racking valves. BrewTools Unitanks are designed and manufactured with special attention to safety and quality. They are tested and certified according to the requirements for PED 2014/68/EU by a third party. Specifications: Low height w/o acc.: 66.1" Max height w/o acc.: 74" Packaging size: 70.8" (h) x 28.3" (w) x 28.3" (d) Net weight: 167.1 lbs Gross weight: 209.4 lbs Tank diameter (inside): Ø23.6" Gross volume: 81.8 gal Max rec. volume: 76.6 gal Min rec. volume: 31.7 gal Volume, cone: 10.5 gal Material: 1.5mm stainless steel (SS304) Operating pressure: 1.0 bar / 15 PSI Max pressure: 2.0 bar / 30 PSI In the box: Unitank with adjustable frame 1 pcs Analog pressure gauge, TC34mm 2 pcs Butterfly-valve, 2" 1 pcs Butterfly-valve, 34mm DN20 1 pcs Blow-off pipe 1 pcs Racking arm 2" 1 pcs TC elbow 90°, 2" 1 pcs Insulation jacket, black neoprene 1 pcs Sample valve, 34mm 1 pcs TC Adapter 8"-4" 1 pcs TC blind cap, 4" 1 pcs TC blind cap 2" 2 pcs TC blind cap 1.5" 3 pcs TC blind cap 34mm 2 pcs TC gasket 8" lipped 2 pcs TC gasket 4" 2 pcs TC gasket 2" 5-pack 1 pcs TC gasket 1.5" 5-pack 3 pcs TC gasket 34mm 5-pack 1 pcs Tri Clamp 8" 1 pcs Tri Clamp 4" 5 pcs Tri Clamp 2" 2 pcs Tri Clamp 1.5" 10 pcs Tri Clamp 34mm 1 pcs TC tool 4 pcs M10 steel/rubber feet 1 pcs TC34mm safety valve (PRV, 2 bar) Necessary bolts and parts for assembly 5 year manufacturer's warranty
Recommended accessories include: HopDrop-kit, Thermowells for your sensors, 34mm Ball-Lock gas adapter for CO2 filling, Coil for sample valve, Spunding valve, Hose barbs for filling and dumping, etc. For User Manuals and support, please follow this link to Brewtools Docs. NOTE: Model in photo is a prototype. Minor changes and improvements may occur.
Unitank Light offers the same tank body as the standard Brewtools Unitank with a slight difference in included accessories for a more affordable price Ferment, cold crash, and carbonate beer all in one vessel with the Brewtools F-Series Unitank Cooling jacket welded to the vertical walls of the tank provide superior cooling capabilities compared to in-solution cooling coils Made from stainless steel throughout with Brewtools' proprietary PureBlast™ surface—no passivation required, simply rinse with warm water before your first use Pressure rated to 30 PSI so you can safely ferment under pressure and pressure transfer finished beer to kegs with virtually no oxygen pickup Brewtools is a Norwegian brand known for high-quality products made without compromise. From brewing systems to fermenters, they continue to push the envelope of innovation for homebrewers around the globe All valves, fittings, and gaskets come included Unitank Light is the same tank body as the standard Brewtools Unitank, but with slightly less equipment and some parts made from Polyketone (POK), which vastly reduces cost without compromising the user experience for smaller tanks. Unitank Light can be upgraded to a standard Unitank where you prefer. Key Differences: CleanCore butterfly valves made from Polyketone Barbed blow-off PRV Can be set to open during fermentation for blow-off Also acts as 2 bar / 30 psi safety valve Pushfit sample valve Compatible with optional Push-fit Coil and Adapter Polyketone 8” to 3” tri-clamp lid adapter replaces stainless steel adapter Polyketone racking arm replaces stainless steel racking arm Does not include neoprene insulation jacket, ss blow-off tube or ss blow-off valve Brewtools Unitanks are fermenters made for ambitious homebrewers and small breweries. As part of the Brewtools identity, they've explored new techniques and solutions. This has resulted in a series of high-end fermentation tanks with new features and a lot of possibilities. Key Features: Brewtools PureBlast™ surface inside and out which eliminate the use of wax and polishing compounds and does not require passivation Cooling jacket in the vertical walls offers efficient cooling without the hassle of cleaning a coil Many options for connecting accessories like sensors, heaters, carb. stones and other accessories Conical pressure rated for 2 bar / 30 PSI Cooling jacket pressure rated for 0.5 bar / 7 PSI 8" TC port on top for easy access 2" TC dump and racking valves Brewtools Unitanks are designed and manufactured with special attention to safety and quality. They are tested and certified according to the requirements for PED 2014/68/EU by a third party. Specifications: Low height w/o acc.: 32.6" Max height w/o acc.: 40.5" Packaging size: 33.4" (h) x 20.5" (w) x 20.5" (d) Net weight: 73 lbs Gross weight: 88 lbs Tank diameter (inside): Ø15.75" Gross volume: 13.5 gal Max rec. volume: 10.5 gal Min rec. volume: 5.3 gal Volume, cone: 3.1 gal Material: 1.5mm stainless steel (SS304) Operating pressure: 1.0 bar / 15 PSI Max pressure: 2.0 bar / 30 PSI Min. pH: 4.0 In the box: Unitank with adjustable frame 1 pcs Analog pressure gauge, TC34mm 2 pcs CleanCore Butterfly-valve, 2" 1 pcs Racking arm 2", POK 1 pcs TC elbow 90°, 2" 1 pcs Sample valve, 34mm, POK 1 pcs TC Adapter 8"-3", POK 1 pcs TC blind cap, 3" 1 pcs TC blind cap 2" 2 pcs TC blind cap 1.5" 4 pcs TC blind cap 34mm 2 pcs TC gasket 8" lipped 2 pcs TC gasket 3" 2 pcs TC gasket 2" 5-pack 1 pcs TC gasket 1.5" 5-pack 3 pcs TC gasket 34mm 5-pack (DN20) 1 pcs Tri Clamp 8" 1 pcs Tri Clamp 3" 5 pcs Tri Clamp 2" 2 pcs Tri Clamp 1.5" 9 pcs Tri Clamp 34mm 1 pcs TC tool 4 pcs M10 steel/rubber feet 1 pcs TC34mm pull-type PRV/Safety valve with 7mm barb 1.5m (4.9') Silicone tube 6x10mm Necessary bolts and parts for assembly 5 year manufacturer's warranty
Recommended accessories include: HopDrop-kit, Thermowells for your sensors, 34mm Ball-Lock gas adapter for CO2 filling, Carb. stone kit with Ball-Lock, Coil for sample valve, Spunding valve, Hose barbs for filling and dumping, 2" sight glass etc. For User Manuals and support, please follow this link to Brewtools Docs. NOTE: Model in photo is a prototype. Minor changes and improvements may occur.
Unitank Light offers the same tank body as the standard Brewtools Unitank with a slight difference in included accessories for a more affordable price
Ferment, cold crash, and carbonate beer all in one vessel with the Brewtools F-Series Unitank
Cooling jacket welded to the vertical walls of the tank provide superior cooling capabilities compared to in-solution cooling coils
Made from stainless steel throughout with Brewtools' proprietary PureBlast™ surface—no passivation required, simply rinse with warm water before your first use
Pressure rated to 30 PSI so you can safely ferment under pressure and pressure transfer finished beer to kegs with virtually no oxygen pickup
Brewtools is a Norwegian brand known for high-quality products made without compromise. From brewing systems to fermenters, they continue to push the envelope of innovation for homebrewers around the globe
All valves, fittings, and gaskets come included
Unitank Light is the same tank body as the standard Brewtools Unitank, but with slightly less equipment and some parts made from Polyketone (POK), which vastly reduces cost without compromising the user experience for smaller tanks. Unitank Light can be upgraded to a standard Unitank where you prefer.
Key Differences:
CleanCore butterfly valves made from Polyketone
Barbed blow-off PRV
Can be set to open during fermentation for blow-off
Also acts as 2 bar / 30 psi safety valve
Pushfit sample valve
Compatible with optional Push-fit Coil and Adapter
Polyketone 8” to 3” tri-clamp lid adapter replaces stainless steel adapter
Polyketone racking arm replaces stainless steel racking arm
Does not include neoprene insulation jacket, ss blow-off tube or ss blow-off valve
Brewtools Unitanks are fermenters made for ambitious homebrewers and small breweries. As part of the Brewtools identity, they've explored new techniques and solutions. This has resulted in a series of high-end fermentation tanks with new features and a lot of possibilities.
Key Features:
Brewtools PureBlast™ surface inside and out which eliminate the use of wax and polishing compounds and does not require passivation
Cooling jacket in the vertical walls offers efficient cooling without the hassle of cleaning a coil
Many options for connecting accessories like sensors, heaters, carb. stones and other accessories
Conical pressure rated for 2 bar / 30 PSI
Cooling jacket pressure rated for 0.5 bar / 7 PSI
8" TC port on top for easy access
2" TC dump and racking valves
Brewtools Unitanks are designed and manufactured with special attention to safety and quality. They are tested and certified according to the requirements for PED 2014/68/EU by a third party.
Specifications:
Low height w/o acc.: 32.6"
Max height w/o acc.: 40.5"
Packaging size: 33.4" (h) x 20.5" (w) x 20.5" (d)
Net weight: 73 lbs
Gross weight: 88 lbs
Tank diameter (inside): Ø15.75"
Gross volume: 13.5 gal
Max rec. volume: 10.5 gal
Min rec. volume: 5.3 gal
Volume, cone: 3.1 gal
Material: 1.5mm stainless steel (SS304)
Operating pressure: 1.0 bar / 15 PSI
Max pressure: 2.0 bar / 30 PSI
Min. pH: 4.0
In the box:
Unitank with adjustable frame
1 pcs Analog pressure gauge, TC34mm
2 pcs CleanCore Butterfly-valve, 2"
1 pcs Racking arm 2", POK
1 pcs TC elbow 90°, 2"
1 pcs Sample valve, 34mm, POK
1 pcs TC Adapter 8"-3", POK
1 pcs TC blind cap, 3"
1 pcs TC blind cap 2"
2 pcs TC blind cap 1.5"
4 pcs TC blind cap 34mm
2 pcs TC gasket 8" lipped
2 pcs TC gasket 3"
2 pcs TC gasket 2" 5-pack
1 pcs TC gasket 1.5" 5-pack
3 pcs TC gasket 34mm 5-pack (DN20)
1 pcs Tri Clamp 8"
1 pcs Tri Clamp 3"
5 pcs Tri Clamp 2"
2 pcs Tri Clamp 1.5"
9 pcs Tri Clamp 34mm
1 pcs TC tool
4 pcs M10 steel/rubber feet
1 pcs TC34mm pull-type PRV/Safety valve with 7mm barb
1.5m (4.9') Silicone tube 6x10mm
Necessary bolts and parts for assembly
5 year manufacturer's warranty
Recommended accessories include: HopDrop-kit, Thermowells for your sensors, 34mm Ball-Lock gas adapter for CO2 filling, Carb. stone kit with Ball-Lock, Coil for sample valve, Spunding valve, Hose barbs for filling and dumping, 2" sight glass etc.
For User Manuals and support, please follow this link to Brewtools Docs.
NOTE: Model in photo is a prototype. Minor changes and improvements may occur.
Unitank Light offers the same tank body as the standard Brewtools Unitank with a slight difference in included accessories for a more affordable price Ferment, cold crash, and carbonate beer all in one vessel with the Brewtools F-Series Unitank Cooling jacket welded to the vertical walls of the tank provide superior cooling capabilities compared to in-solution cooling coils Made from stainless steel throughout with Brewtools' proprietary PureBlast™ surface—no passivation required, simply rinse with warm water before your first use Pressure rated to 30 PSI so you can safely ferment under pressure and pressure transfer finished beer to kegs with virtually no oxygen pickup Brewtools is a Norwegian brand known for high-quality products made without compromise. From brewing systems to fermenters, they continue to push the envelope of innovation for homebrewers around the globe All valves, fittings, and gaskets come included Unitank Light is the same tank body as the standard Brewtools Unitank, but with slightly less equipment and some parts made from Polyketone (POK), which vastly reduces cost without compromising the user experience for smaller tanks. Unitank Light can be upgraded to a standard Unitank where you prefer. Key Differences: CleanCore butterfly valves made from Polyketone Barbed blow-off PRV Can be set to open during fermentation for blow-off Also acts as 2 bar / 30 psi safety valve Pushfit sample valve Compatible with optional Push-fit Coil and Adapter Polyketone 8” to 3” tri-clamp lid adapter replaces stainless steel adapter Polyketone racking arm replaces stainless steel racking arm Does not include neoprene insulation jacket, ss blow-off tube or ss blow-off valve Brewtools Unitanks are fermenters made for ambitious homebrewers and small breweries. As part of the Brewtools identity, they've explored new techniques and solutions. This has resulted in a series of high-end fermentation tanks with new features and a lot of possibilities. Key Features: Brewtools PureBlast™ surface inside and out which eliminate the use of wax and polishing compounds and does not require passivation Cooling jacket in the vertical walls offers efficient cooling without the hassle of cleaning a coil Many options for connecting accessories like sensors, heaters, carb. stones and other accessories Conical pressure rated for 2 bar / 30 PSI Cooling jacket pressure rated for 0.5 bar / 7 PSI 8" TC port on top for easy access 2" TC dump and racking valves Brewtools Unitanks are designed and manufactured with special attention to safety and quality. They are tested and certified according to the requirements for PED 2014/68/EU by a third party. Specifications: Low height w/o acc.: 32.6" Max height w/o acc.: 40.5" Packaging size: 33.4" (h) x 20.5" (w) x 20.5" (d) Net weight: 73 lbs Gross weight: 88 lbs Tank diameter (inside): Ø15.75" Gross volume: 13.5 gal Max rec. volume: 10.5 gal Min rec. volume: 5.3 gal Volume, cone: 3.1 gal Material: 1.5mm stainless steel (SS304) Operating pressure: 1.0 bar / 15 PSI Max pressure: 2.0 bar / 30 PSI Min. pH: 4.0 In the box: Unitank with adjustable frame 1 pcs Analog pressure gauge, TC34mm 2 pcs CleanCore Butterfly-valve, 2" 1 pcs Racking arm 2", POK 1 pcs TC elbow 90°, 2" 1 pcs Sample valve, 34mm, POK 1 pcs TC Adapter 8"-3", POK 1 pcs TC blind cap, 3" 1 pcs TC blind cap 2" 2 pcs TC blind cap 1.5" 4 pcs TC blind cap 34mm 2 pcs TC gasket 8" lipped 2 pcs TC gasket 3" 2 pcs TC gasket 2" 5-pack 1 pcs TC gasket 1.5" 5-pack 3 pcs TC gasket 34mm 5-pack (DN20) 1 pcs Tri Clamp 8" 1 pcs Tri Clamp 3" 5 pcs Tri Clamp 2" 2 pcs Tri Clamp 1.5" 9 pcs Tri Clamp 34mm 1 pcs TC tool 4 pcs M10 steel/rubber feet 1 pcs TC34mm pull-type PRV/Safety valve with 7mm barb 1.5m (4.9') Silicone tube 6x10mm Necessary bolts and parts for assembly 5 year manufacturer's warranty
Recommended accessories include: HopDrop-kit, Thermowells for your sensors, 34mm Ball-Lock gas adapter for CO2 filling, Carb. stone kit with Ball-Lock, Coil for sample valve, Spunding valve, Hose barbs for filling and dumping, 2" sight glass etc. For User Manuals and support, please follow this link to Brewtools Docs. NOTE: Model in photo is a prototype. Minor changes and improvements may occur.
Ferment, cold crash, and carbonate beer all in one vessel with the Brewtools F-Series Unitank Cooling jacket welded to the vertical walls of the tank provide superior cooling capabilities compared to in-solution cooling coils Made from stainless steel throughout with Brewtools' proprietary PureBlast™ surface—no passivation required, simply rinse with warm water before your first use Pressure rated to 30 PSI so you can safely ferment under pressure and pressure transfer finished beer to kegs with virtually no oxygen pickup Brewtools is a Norwegian brand known for high-quality products made without compromise. From brewing systems to fermenters, they continue to push the envelope of innovation for homebrewers around the globe All valves, fittings, and gaskets come included Brewtools Unitanks are fermenters made for ambitious homebrewers and small breweries. As part of the Brewtools identity, they've explored new techniques and solutions. This has resulted in a series of high-end fermentation tanks with new features and a lot of possibilities. Key Features: Brewtools PureBlast™ surface inside and out which eliminate the use of wax and polishing compounds and does not require passivation Cooling jacket in the vertical walls offers efficient cooling without the hassle of cleaning a coil Many options for connecting accessories like sensors, heaters, carb. stones and other accessories Conical pressure rated for 2 bar / 30 PSI Cooling jacket pressure rated for 0.5 bar / 7 PSI 8" TC port on top for easy access 2" TC dump and racking valves Brewtools Unitanks are designed and manufactured with special attention to safety and quality. They are tested and certified according to the requirements for PED 2014/68/EU by a third party. Specifications: Low height w/o acc.: 32.6" Max height w/o acc.: 40.5" Packaging size: 33.4" (h) x 20.5" (w) x 20.5" (d) Net weight: 84 lbs Gross weight: 98 lbs Tank diameter (inside): Ø15.75" Gross volume: 13.5 gal Max rec. volume: 10.5 gal Min rec. volume: 5.3 gal Volume, cone: 3.1 gal Material: 1.5mm stainless steel (SS304) Operating pressure: 1.0 bar / 15 PSI Max pressure: 2.0 bar / 30 PSI In the box: Unitank with adjustable frame 1 pcs Analog pressure gauge, TC34mm 2 pcs Butterfly-valve, 2" 1 pcs Butterfly-valve, 34mm DN20 1 pcs Blow-off pipe 1 pcs Racking arm 2" 1 pcs TC elbow 90°, 2" 1 pcs Insulation jacket, black neoprene 1 pcs Sample valve, 34mm 1 pcs TC Adapter 8"-3" 1 pcs TC blind cap, 3" 1 pcs TC blind cap 2" 2 pcs TC blind cap 1.5" 3 pcs TC blind cap 34mm 2 pcs TC gasket 8" lipped 2 pcs TC gasket 3" 2 pcs TC gasket 2" 5-pack 1 pcs TC gasket 1.5" 5-pack 3 pcs TC gasket 34mm 5-pack (DN20) 1 pcs Tri Clamp 8" 1 pcs Tri Clamp 3" 5 pcs Tri Clamp 2" 2 pcs Tri Clamp 1.5" 10 pcs Tri Clamp 34mm 1 pcs TC tool 4 pcs M10 steel/rubber feet 1 pcs TC34mm safety valve (PRV, 2 bar) Necessary bolts and parts for assembly 5 year manufacturer's warranty
Recommended accessories include: HopDrop-kit, Thermowells for your sensors, 34mm Ball-Lock gas adapter for CO2 filling, Coil for sample valve, Spunding valve, Hose barbs for filling and dumping, etc. For User Manuals and support, please follow this link to Brewtools Docs. NOTE: Model in photo is a prototype. Minor changes and improvements may occur.
Unitank Light offers the same tank body as the standard Brewtools Unitank with a slight difference in included accessories for a more affordable price Ferment, cold crash, and carbonate beer all in one vessel with the Brewtools F-Series Unitank Cooling jacket welded to the vertical walls of the tank provide superior cooling capabilities compared to in-solution cooling coils Made from stainless steel throughout with Brewtools' proprietary PureBlast™ surface—no passivation required, simply rinse with warm water before your first use Pressure rated to 30 PSI so you can safely ferment under pressure and pressure transfer finished beer to kegs with virtually no oxygen pickup Brewtools is a Norwegian brand known for high-quality products made without compromise. From brewing systems to fermenters, they continue to push the envelope of innovation for homebrewers around the globe All valves, fittings, and gaskets come included Unitank Light is the same tank body as the standard Brewtools Unitank, but with slightly less equipment and some parts made from Polyketone (POK), which vastly reduces cost without compromising the user experience for smaller tanks. Unitank Light can be upgraded to a standard Unitank where you prefer. Key Differences: CleanCore butterfly valves made from Polyketone Barbed blow-off PRV Can be set to open during fermentation for blow-off Also acts as 2 bar / 30 psi safety valve Pushfit sample valve Compatible with optional Push-fit Coil and Adapter Polyketone 8” to 3” tri-clamp lid adapter replaces stainless steel adapter Polyketone racking arm replaces stainless steel racking arm Does not include neoprene insulation jacket, ss blow-off tube or ss blow-off valve Brewtools Unitanks are fermenters made for ambitious homebrewers and small breweries. As part of the Brewtools identity, they've explored new techniques and solutions. This has resulted in a series of high-end fermentation tanks with new features and a lot of possibilities. Key Features: Brewtools PureBlast™ surface inside and out which eliminate the use of wax and polishing compounds and does not require passivation Cooling jacket in the vertical walls offers efficient cooling without the hassle of cleaning a coil Many options for connecting accessories like sensors, heaters, carb. stones and other accessories Conical pressure rated for 2 bar / 30 PSI Cooling jacket pressure rated for 0.5 bar / 7 PSI 8" TC port on top for easy access 2" TC dump and racking valves Brewtools Unitanks are designed and manufactured with special attention to safety and quality. They are tested and certified according to the requirements for PED 2014/68/EU by a third party. Specifications: Low height w/o acc.: 43.3" Max height w/o acc.: 51.2" Packaging size: 44.5" (h) x 20.5" (w) x 20.5" (d) Net weight: 88 lbs Gross weight: 101 lbs Tank diameter (inside): Ø15.75" Gross volume: 22.7 gal Max rec. volume: 21.1 gal Min rec. volume: 5.3 gal Volume, cone: 3.1 gal Material: 1.5mm stainless steel (SS304) Operating pressure: 1.0 bar / 15 PSI Max pressure: 2.0 bar / 30 PSI In the box: Unitank with adjustable frame 1 pcs Analog pressure gauge, TC34mm 2 pcs CleanCore Butterfly-valve, 2" 1 pcs Racking arm 2", POK 1 pcs TC elbow 90°, 2" 1 pcs Sample valve, 34mm, POK 1 pcs TC Adapter 8"-3", POK 1 pcs TC blind cap, 3" 1 pcs TC blind cap 2" 2 pcs TC blind cap 1.5" 4 pcs TC blind cap 34mm 2 pcs TC gasket 8" lipped 2 pcs TC gasket 3" 2 pcs TC gasket 2" 5-pack 1 pcs TC gasket 1.5" 5-pack 3 pcs TC gasket 34mm 5-pack (DN20) 1 pcs Tri Clamp 8" 1 pcs Tri Clamp 3" 5 pcs Tri Clamp 2" 2 pcs Tri Clamp 1.5" 9 pcs Tri Clamp 34mm 1 pcs TC tool 4 pcs M10 steel/rubber feet 1 pcs TC34mm pull-type PRV/Safety valve with 7mm barb 1.5m (4.9') Silicone tube 6x10mm Necessary bolts and parts for assembly 5 year manufacturer's warranty
Recommended accessories include: HopDrop-kit, Thermowells for your sensors, 34mm Ball-Lock gas adapter for CO2 filling, Carb. stone kit with Ball-Lock, Coil for sample valve, Spunding valve, Hose barbs for filling and dumping, 2" sight glass etc. For User Manuals and support, please follow this link to Brewtools Docs. NOTE: Model in photo is a prototype. Minor changes and improvements may occur.
Ferment, cold crash, and carbonate beer all in one vessel with the Brewtools F-Series Unitank Cooling jacket welded to the vertical walls of the tank provide superior cooling capabilities compared to in-solution cooling coils Made from stainless steel throughout with Brewtools' proprietary PureBlast™ surface—no passivation required, simply rinse with warm water before your first use Pressure rated to 30 PSI so you can safely ferment under pressure and pressure transfer finished beer to kegs with virtually no oxygen pickup Brewtools is a Norwegian brand known for high-quality products made without compromise. From brewing systems to fermenters, they continue to push the envelope of innovation for homebrewers around the globe All valves, fittings, and gaskets come included Brewtools Unitanks are fermenters made for ambitious homebrewers and small breweries. As part of the Brewtools identity, they've explored new techniques and solutions. This has resulted in a series of high-end fermentation tanks with new features and a lot of possibilities. Key Features: Brewtools PureBlast™ surface inside and out which eliminate the use of wax and polishing compounds and does not require passivation Cooling jacket in the vertical walls offers efficient cooling without the hassle of cleaning a coil Many options for connecting accessories like sensors, heaters, carb. stones and other accessories Pressure rated for 2 bar / 30 PSI Cooling jacket pressure rated for 0.5 bar / 7 PSI 8" TC port on top for easy access 2" TC dump and racking valves Brewtools Unitanks are designed and manufactured with special attention to safety and quality. They are tested and certified according to the requirements for PED 2014/68/EU by a third party. Specifications: Low height w/o acc.: 43.3" Max height w/o acc.: 51.2" Packaging size: 44.5" (h) x 20.5" (w) x 20.5" (d) Net weight: 99 lbs Gross weight: 110 lbs Tank diameter (inside): Ø15.75" Gross volume: 22.7 gal Max rec. volume: 21.1 gal Min rec. volume: 5.3 gal Volume, cone: 3.1 gal Material: 1.5mm stainless steel (SS304) Operating pressure: 1.0 bar / 15 PSI Max pressure: 2.0 bar / 30 PSI In the box: Unitank with adjustable frame 1 pcs Analog pressure gauge, TC34mm 2 pcs Butterfly-valve, 2" 1 pcs Butterfly-valve, 34mm DN20 1 pcs Blow-off pipe 1 pcs Racking arm 2" 1 pcs TC elbow 90°, 2" 1 pcs Insulation jacket, black neoprene 1 pcs Sample valve, 34mm 1 pcs TC Adapter 8"-3" 1 pcs TC blind cap, 3" 1 pcs TC blind cap 2" 2 pcs TC blind cap 1.5" 3 pcs TC blind cap 34mm 2 pcs TC gasket 8" lipped 2 pcs TC gasket 3" 2 pcs TC gasket 2" 5-pack 1 pcs TC gasket 1.5" 5-pack 3 pcs TC gasket 34mm 5-pack (DN20) 1 pcs Tri Clamp 8" 1 pcs Tri Clamp 3" 5 pcs Tri Clamp 2" 2 pcs Tri Clamp 1.5" 10 pcs Tri Clamp 34mm 1 pcs TC tool 4 pcs M10 steel/rubber feet 1 pcs TC34mm safety valve (PRV, 2 bar) Necessary bolts and parts for assembly 5 year manufacturer's warranty
Recommended accessories include: HopDrop-kit, Thermowells for your sensors, 34mm Ball-Lock gas adapter for CO2 filling, Coil for sample valve, Spunding valve, Hose barbs for filling and dumping, etc. For User Manuals and support, please follow this link to Brewtools Docs. NOTE: Model in photo is a prototype. Minor changes and improvements may occur.
Optimal Liquid Consistency: Magnetic-drive impeller evens out temperature gradients and maximizes hop utilization.
Smart Integration: Fully adjustable via FCS Display Module with support for automated interval mixing in future profiles.
Universal Compatibility: Fits most fermentation and brite tanks using tri-clamp adapters for flexible installation.
Agitator for FCS
Impeller based stirring system with magnetic drive for fermentation and brite tanks. The agitator mixes the liquid to even out temperature differences and can in many cases increase the utilization of hops and other additives. Speed is adjustable from the FCS Display Module. The agitator will also be able to be run at intervals in the upcoming advanced fermentation profiles in FCS.
The agitator can also be used without FCS with an adapter (BT1328) and a power supply (BT1324). The motor can be started with the button of top of the drive unit. Speed is controlled by pushing it multiple times and holding the button stops the motor.
Our agitator can be used on most fermentation and brite tanks with the help of adapters, as long as the impeller stays clear of the vertical wall.
Specifications:
Motor: Brushed DC motor, 500 RPM, 24V, 0.5A
Impeller material: POK, acid proof and food grade
Flange: TC 34mm. Ø19mm minimum
Length: 380mm / 14.9" from flange
Connector: LP12 5-pin (CAN bus + 24V)
Note: For F40 and other smaller tanks, it might be necessary to lift the agitator to avoid touching the cone wall using a tee or short pipe.
Density sensor with integrated temperature sensor for FCS gives accurate and real-time density and temperature data for your fermentation tank Measures density by inducing a vibration frequency in the fork and listening for the resonant frequency Primarily designed for fermentation tanks like the F40-F300 and similar tanks Tuning fork-based measurements gives accurate and real-time density and temperature data for your fermentation tank. The Brewtools density sensor measures density by inducing a vibration frequency in the fork and listening for the resonant frequency. Take your fermentation to the next level with data-driven control and logging. Future updates of FCS will enable you to control temperature and pressure steps based on density in the tank, without the need for manual intervention. This model is primarily designed for fermentation tanks like our F40-F300 and similar tanks. Accuracy may vary for smaller tanks (like MiniUni+). More information: https://docs.brewtools.com/density-sensor Specifications: Density accuracy: +-0.002 SG Temperature accuracy: +- 0.3ºC Flange: TC 1.5". Ø25mm minimum Length: 200mm from flange Connector: LP12 5-pin (CAN bus + 24V) Note: Accuracy and function can vary based on trub, yeast health, yeast flocculation, rapid temperature changes, dry-hopping and other additions and distance to tank wall/heating elements etc. Pressure fermentation can increase accuracy. Accuracy and features will improve over time with software updates. Brewtools Product Number: 7713723
Precision Cone Measurement: High-accuracy radar technology tracks volume all the way down to the tank cone, eliminating guesswork during filling or packaging.
Rapid Calibration: Simplified setup process allows you to configure volume and dimensions quickly using a basic water-fill reference.
Direct-Mount Reliability: Optimized for vertical flange installation to ensure a clear signal path and maximum measurement stability.
Radar based level sensor for FCS
The days of guessing tank the volume during filling or kegging/bottling is over. Radar based level sensor designed to measure the tank volume down to the cone in a fermentation tank.
The sensor is configured by setting the volume, tank diameter and distance to the cone. It's easily done by filling water in the tank to the top of the cone.
The sensor must be installed on a vertical flange on the top of the tank, ideally on a single port welded on the curved top surface. Avoid using tees/pipes between the sensor and the tank.
Specifications:
Measuring distance: 0-3m / 0-9.8 ft (Preliminary)
Flange: TC 1.5". Ø19mm minimum
Connector: LP12 5-pin (CAN bus + 24V)
Note: During fermentation the krausen/foam will give incorrect values. Cooling spirals etc inside the tank may give incorrect readings.
Precision Cone Measurement: High-accuracy radar technology tracks volume all the way down to the tank cone, eliminating guesswork during filling or packaging.
Rapid Calibration: Simplified setup process allows you to configure volume and dimensions quickly using a basic water-fill reference.
Direct-Mount Reliability: Optimized for vertical flange installation to ensure a clear signal path and maximum measurement stability.
Radar based level sensor for FCS
The days of guessing tank the volume during filling or kegging/bottling is over. Radar based level sensor designed to measure the tank volume down to the cone in a fermentation tank.
The sensor is configured by setting the volume, tank diameter and distance to the cone. It's easily done by filling water in the tank to the top of the cone.
The sensor must be installed on a vertical flange on the top of the tank, ideally on a single port welded on the curved top surface. Avoid using tees/pipes between the sensor and the tank.
Specifications:
Measuring distance: 0-3m / 0-9.8 ft. (Preliminary)
Flange: TC34mm. Ø19mm minimum
Connector: LP12 5-pin (CAN bus + 24V)
Note: During fermentation the krausen/foam will give incorrect values. Cooling spirals etc inside the tank may give incorrect readings.
Relay Module for use with FCS. Specifically designed for small heating elements.
Control signal is 5V and the devices measures current draw.
The module has a 2-pole relay and several protective circuits for noise, over voltage etc.
For maximum safety, the device also has one fuse per phase.
Specifications:
110-240V AC, Max 5A
Power in: LP20 3-pin male
Power out: LP20 3-pin female
Signal: LP12 7-pin
Fuse: 2x 5x20 6.3A Fast Blow
Installation:
4 screw holes with 5mm diameter. Designed for countersunk screws.
Advanced Modular Control System: Designed for homebrewers and microbreweries, the Brewtools FCS brings industrial-level precision with features like temperature, pressure, and gravity monitoring for ultimate brewing control. Comprehensive Starter Kit: Includes essential components such as FCS Display and I/O Modules, temperature and pressure sensors, and all necessary cables and adapters to start customizing your fluid control setup. Automated Fermentation Profiles: Automate cooling, heating, and pressure management with software-driven profiles, simplifying complex processes while ensuring consistency in your brews. Expandable & Customizable: Add solenoids, pumps, airlocks, and adapters to fit your specific brewing needs, compatible with both Brewtools and non-Brewtools tanks. Constant Monitoring & Alerts: Early warning notifications for equipment issues like solenoid valves or heating elements ensure smooth operation and protect your brewing investment. This version of the FCS Kit includes the Density/Temp Sensor which replaces the temperature-only sensor in the basic FCS Starter Kit. FCS is a modular control system designed, developed and manufactured by Brewtools in Norway. The vision behind the system is to take industrial technology and make that available for microbreweries and homebrewers. Using the latest electronic component technology and clever software engineering, Brewtools is able to make features that used to be very expensive and complicated available for everyone. The system can measure temperature, pressure, density/gravity, level* and power consumption and based on that — control cooling, heating, pressure/CO2 in, pressure/CO2 out, agitation*, automatic hop additions* under pressure and more! Fermentation profiles will automate the whole process and give you ultimate control of your fermentation process. (*Not available at first launch.) The system will also constantly monitor the process and notify you if something isn't right. For example, the system will measure the current draw of solenoid valves and heating elements, and will notify you if these components aren't working as they should. Please Note: The software is currently in a state of early adopter beta, and should not be used for critical production. Brewtools will continue to develop software and new sensors/actuators based on customer feedback and requests. If you cannot find a sensor or actuator that fits your setup, please reach out to us and let us know. Note that we do not take responsibility for any lost/destroyed beer or raw materials. Brewtools FCS Starter Kit for Pro Tanks This kit includes everything you would normally need to install the system on a "standard" tank. It comes with two TC 1.5" tees (short) and parts needed to connect your existing solenoids for cooling. The solenoid for gas out is also made for larger tanks. FCS Display Module and FCS I/O Module with power supply Density sensor (300mm) 1 pressure sensor with gas out pro solenoid Tiny Relay Module for wiring your cooling solenoid 2x TC Tees, clamps and gaskets All cables and adapters needed (3m length) The kit does not include a valve/pump for cooling as these are tank dependent, and you may already have a solenoid for your existing glycol loop. For non-Brewtools tanks, you also may need an adapter and/or tee to connect the spunding valve/pressure sensor assembly. Accessories To complete your FCS kit setup, some accessories are needed. A solenoid for cooling (Ø4.5mm - 34mm or 1.5") with 2-pin LP12 cable and DIN43650 Type A adapter or a submersible pump (comes with cable). A blowoff for the pressure out solenoid valve is recommended. You will need a 1.5" TC adapter to connect to your preferred blowoff tubing. Tri-Clamps and gaskets. Based on your tank and setup, you may need some extra tri-clamps or gaskets. Setting Up the FCS for Your Tank Solenoid Valve & Related Connection Hardware for Cooling For Brewtools tanks that use 34mm connection you will need a Ø4.5mm - 34mm solenoid valve. For Commercial tanks you will need a TC 1.5" to 34mm adapter and 1.5" TC Solenoid Valve. Either way, you will need a 2-pin LP12 cable and DIN43650 Type A adapter to connect the solenoid valve to the Brewtools FCS I/O Module. Would You Like a Visible Air Lock on the Spunding Valve? The Brewtools pressure relief solenoid spunding valve releases CO2 at the set point you choose on your controller. To visually see the CO2 release, add a blowoff to the pressure relief solendoid using a 1.5" TC adapter to your preferred tubing size. Starter Kit Included Parts: FCS Display Module, 5" FCS I/O Module 2x RTD, 5x CAN, 4x Relay Power Supply, 24V 40W, LP12-pin Pressure Sensor, CAN BUS 24V, M12 Solenoid valve, TC1.5" + M12, DC24V Ø2.0 Density/Temp Sensor 300mm, TC 1.5", CAN BUS 24V Cable, LP12 6-pin, 3m Cable, LP12 5-pin, 3m (2 pcs) Cable, LP12-pin, 3m (2 pcs) Adapter, LP12-pin to DIN 43650 Type B FCS Tiny Relay Module TC Tee 1.5", L=90mm (2 pcs) Tri Clamps og gaskets (1.5") Ball mount for pipes (28,33,38mm) and connecting joint
Advanced Modular Control System: Designed for homebrewers and microbreweries, the Brewtools FCS brings industrial-level precision with features like temperature, pressure, and gravity monitoring for ultimate brewing control. Comprehensive Starter Kit: Includes essential components such as FCS Display and I/O Modules, temperature and pressure sensors, and all necessary cables and adapters to start customizing your fluid control setup. Automated Fermentation Profiles: Automate cooling, heating, and pressure management with software-driven profiles, simplifying complex processes while ensuring consistency in your brews. Expandable & Customizable: Add solenoids, pumps, airlocks, and adapters to fit your specific brewing needs, compatible with both Brewtools and non-Brewtools tanks. Constant Monitoring & Alerts: Early warning notifications for equipment issues like solenoid valves or heating elements ensure smooth operation and protect your brewing investment. An upgraded version of the FCS Starter Kit w/ Density Sensor is also available. FCS is a modular control system designed, developed and manufactured by Brewtools in Norway. The vision behind the system is to take industrial technology and make that available for microbreweries and homebrewers. Using the latest electronic component technology and clever software engineering, Brewtools is able to make features that used to be very expensive and complicated available for everyone. The system can measure temperature, pressure, density/gravity*, level* and power consumption and based on that — control cooling, heating, pressure/CO2 in, pressure/CO2 out, agitation*, automatic hop additions* under pressure and more! Fermentation profiles will automate the whole process and give you ultimate control of your fermentation process. (*Not available at first launch.) The system will also constantly monitor the process and notify you if something isn't right. For example, the system will measure the current draw of solenoid valves and heating elements, and will notify you if these components aren't working as they should. Please Note: The software is currently in a state of early adopter beta, and should not be used for critical production. Brewtools will continue to develop software and new sensors/actuators based on customer feedback and requests. If you cannot find a sensor or actuator that fits your setup, please reach out to us and let us know. Note that we do not take responsibility for any lost/destroyed beer or raw materials. Brewtools FCS Starter Kit The Brewtools FCS Starter Kit includes all the essential parts to get you started setting up your own custom-designed Fluid Control System. FCS Display Module and FCS I/O Module with power supply 1 temperature sensor (TC 1.5" 160mm) 1 pressure sensor with gas out solenoid All cables and adapters needed (3m length) The kit does not include a valve/pump for cooling as these are tank dependent, and you may already have a solenoid for your existing glycol loop. For non-Brewtools tanks, you also may need an adapter and/or tee to connect the spunding valve/pressure sensor assembly. Accessories To complete your FCS kit setup, some accessories are needed. A solenoid for cooling (Ø4.5mm - 34mm or 1.5") with 2-pin LP12 cable and DIN43650 Type A adapter or a submersible pump (comes with cable). A ball clamp and a connecting rod. An airlock for the pressure out solenoid valve is recommended. For smaller tanks we recommend our polycarbonate airlock. For larger tanks (300l+) you should use a TC34mm to 12mm barb and a 10x16mm silicone tube or equivalent. Tri-Clamps and gaskets. Based on your tank and setup, you may need some extra tri-clamps or gaskets. For MiniUni+, you need to replace the Mini Spunding valve with an M24 to Tri Clamp adapter and a 90 degree TC34mm elbow to fit your spunding assembly (if you want to use our TC air lock. No need for elbow if you use tubing as airlock). Rembember clamps/gaskets. If you don't have a Brewtools Unitank, we recommend getting TC 1.5" to 34mm adapter for the spunding setup. You will also need a 34mm Tri-Clamp and 34mm gasket. Tees and crosses are also available in multiple sizes to give you more ports. Starter Kit Included Parts: FCS Display Module, 5" FCS I/O Module 2x RTD, 5x CAN, 4x Relay Power Supply, 24V 40W, LP12-pin Pressure Sensor, CAN BUS 24V, M12 Solenoid valve, TC34mm + M12, DC24V Ø2.0 Temp Sensor, PT100, TC 1.5", 160mm Cable, LP12 6-pin, 3m Cable, LP12 5-pin, 3m Cable, LP12 3-pin, 3m Cable, LP12-pin, 3m Adapter, LP12-pin to DIN 43650 Type B Recommended Separate Parts: Solenoid valve for cooling with adapters/cables or submersible pump Ball Mount connector and pipe clamp etc. Airlock (Top mounted or barb with silicone tube) Adapters and fittings to fit your tank Brewtools Product Number: 7713567
Advanced Modular Control System: Designed for homebrewers and microbreweries, the Brewtools FCS brings industrial-level precision with features like temperature, pressure, and gravity monitoring for ultimate brewing control. Comprehensive Starter Kit: Includes essential components such as FCS Display and I/O Modules, temperature and pressure sensors, and all necessary cables and adapters to start customizing your fluid control setup. Automated Fermentation Profiles: Automate cooling, heating, and pressure management with software-driven profiles, simplifying complex processes while ensuring consistency in your brews. Expandable & Customizable: Add solenoids, pumps, airlocks, and adapters to fit your specific brewing needs, compatible with both Brewtools and non-Brewtools tanks. Constant Monitoring & Alerts: Early warning notifications for equipment issues like solenoid valves or heating elements ensure smooth operation and protect your brewing investment. This version of the FCS Kit includes the Density/Temp Sensor which replaces the temperature-only sensor in the basic FCS Starter Kit. FCS is a modular control system designed, developed and manufactured by Brewtools in Norway. The vision behind the system is to take industrial technology and make that available for microbreweries and homebrewers. Using the latest electronic component technology and clever software engineering, Brewtools is able to make features that used to be very expensive and complicated available for everyone. The system can measure temperature, pressure, density/gravity*, level* and power consumption and based on that — control cooling, heating, pressure/CO2 in, pressure/CO2 out, agitation*, automatic hop additions* under pressure and more! Fermentation profiles will automate the whole process and give you ultimate control of your fermentation process. (*Not available at first launch.) The system will also constantly monitor the process and notify you if something isn't right. For example, the system will measure the current draw of solenoid valves and heating elements, and will notify you if these components aren't working as they should. Please Note: The software is currently in a state of early adopter beta, and should not be used for critical production. Brewtools will continue to develop software and new sensors/actuators based on customer feedback and requests. If you cannot find a sensor or actuator that fits your setup, please reach out to us and let us know. Note that we do not take responsibility for any lost/destroyed beer or raw materials. Brewtools FCS Starter Kit The Brewtools FCS Starter Kit includes all the essential parts to get you started setting up your own custom-designed Fluid Control System. FCS Display Module and FCS I/O Module with power supply 1 density/temp sensor (TC 1.5") 1 pressure sensor with gas out solenoid All cables and adapters needed (3m length) The kit does not include a valve/pump for cooling as these are tank dependent, and you may already have a solenoid for your existing glycol loop. For non-Brewtools tanks, you also may need an adapter and/or tee to connect the spunding valve/pressure sensor assembly. Accessories To complete your FCS kit setup, some accessories are needed. A solenoid for cooling (Ø4.5mm - 34mm or 1.5") with 2-pin LP12 cable and DIN43650 Type A adapter or a submersible pump (comes with cable). A ball clamp and a connecting rod. An airlock for the pressure out solenoid valve is recommended. For smaller tanks we recommend our polycarbonate airlock. For larger tanks (300L+) you should use a TC34mm to 12mm barb and a 10x16mm silicone tube or equivalent. Tri-Clamps and gaskets. Based on your tank and setup, you may need some extra tri-clamps or gaskets. For MiniUni+, you need to replace the Mini Spunding valve with an M24 to Tri Clamp adapter and a 90 degree TC34mm elbow to fit your spunding assembly (if you want to use our TC air lock. No need for elbow if you use tubing as airlock). Remember clamps/gaskets. If you don't have a Brewtools Unitank, we recommend getting a TC 1.5" to 34mm adapter for the spunding setup. You will also need a 34mm Tri-Clamp and 34mm gasket. Tees and crosses are also available in multiple sizes to give you more ports. Setting Up the FCS for Your Tank Mounting To mount to your tank a ball clamp and a connecting rod are very useful. This will work with most any size or style tank. Solenoid Valve & Related Connection Hardware for Cooling For Brewtools tanks that use 34mm connection you will need a Ø4.5mm - 34mm solenoid valve. For BrewBuilt, Spike, Ss BrewTech, or Commercial tanks you will need a TC 1.5" to 34mm adapter and 1.5" TC Solenoid Valve. Either way, you will need a 2-pin LP12 cable and DIN43650 Type A adapter to connect the solenoid valve to the Brewtools FCS I/O Module. Would You Like a Visible Air Lock on the Spunding Valve? The Brewtools pressure relief solenoid spunding valve releases CO2 at the set point you choose on your controller. To visually see the CO2 release, adding on an airlock for the pressure out solenoid valve is a nice option. For tanks under 300L, we recommend the 34mm polycarbonate airlock that connects to the Brewtools Solenoid Valve. For tanks larger than 300L, you should use a blowoff. For blowoffs, use a TC34mm to 12mm barb and a 10x16mm silicone tube or equivalent ran into a bucket of water. You will also need a 34mm Tri-Clamp and 34mm gasket. Tees and crosses are also available in multiple sizes to give you more ports. For the MiniUni+ For MiniUni+, you need to replace the Mini Spunding Valve with an M24 to TC adapter and a 90-degree 34mm TC elbow to fit your spunding assembly (if you want to use the TC air lock. No need for elbow if you use tubing for a blowoff). You will need the clamps/gaskets to make the connection. Starter Kit Included Parts: FCS Display Module, 5" FCS I/O Module 2x RTD, 5x CAN, 4x Relay Power Supply, 24V 40W, LP12-pin Pressure Sensor, CAN BUS 24V, M12 Solenoid valve, TC34mm + M12, DC24V Ø2.0 Density/Temp Sensor, TC 1.5", CAN BUS 24V Cable, LP12 6-pin, 3m Cable, LP12 5-pin, 3m (2 pcs) Cable, LP12-pin, 3m Adapter, LP12-pin to DIN 43650 Type B Recommended Separate Parts: Solenoid valve for cooling with adapters/cables or submersible pump Ball Mount connector and pipe clamp etc. Airlock (Top mounted or barb with silicone tube) Adapters and fittings to fit your tank Brewtools Product Number: 7713792
Ball Lock adapter (Gas) to TC 34mm. The adapter is made for CMB or other gas-fittings.
M16x1.5mm inside threads for accessories.
The Gas model is identified with a groove near the TC connector.
2" TC Sanitary heating element designed for use in santary applications where ease of cleaning is important. The heating element is designed to get the lowest possible watt density and is very easy to clean. Perfect for use with Brewtools Unitanks with kveik yeast or other high temperature fermentation applications.
Can also be used in cominbation with 2" TC pipes for RIMS applications.
Note that the product comes without any temperature or power control. The manufacturer does not take responsibility for incorrect use or use with too much power output. A PID-regulator may be needed to maintain accurate temperatures.
Diameter: Ø42mm (1.65")
Length: ~300mm (~11.8")
Included:
Heating element
Power cable 2 meter
2" TC Sanitary heating element designed for use in santary applications where ease of cleaning is important. The heating element is designed to get the lowest possible watt density and is very easy to clean. Perfect for use with Brewtools Unitanks with kveik yeast or other high temperature fermentation applications.
Can also be used in cominbation with 2" TC pipes for RIMS applications.
Note that the product comes without any temperature or power control. The manufacturer does not take responsibility for incorrect use or use with too much power output. A PID-regulator may be needed to maintain accurate temperatures.
Diameter: Ø42mm (1.65")
Length: ~300mm (~11.8")
Included:
Heating element
Power cable 2 meter
Kit for dryhopping and adding other ingredients to a pressurized fermenter without oxygen. This is the correct size for the Brewtools F40 and F80 Unitanks.
Included in the box:
Butterfly-valve, TC 3"
TC Adapter, 3" to 34mm
TC Pipe, 3", L=200mm
Tri Clamp, 3" (2 pcs)
Tri Clamp, 34mm (3 pcs)
TC34mm Manual PRV
TC34mm Ball Lock connector, Gas
TC Tee, 34mm, L=60mm
TC Gasket, 3", (3 pcs)
TC Gasket, 34mm DN20, 5-pack
Kit for dryhopping and adding other ingredients to a pressurized fermenter without oxygen. This is the correct size for the Brewtools F150 Unitank.
Included in the box:
Butterfly-valve, TC 4"
TC Adapter, 4" til 34mm
TC Pipe, 4", L=200mm
Tri Clamp, 4" (2 pcs)
Tri Clamp, 34mm (3 pcs)
TC34mm Manual PRV
TC34mm Ball Lock connector, Gas
TC Tee, 34mm, L=60mm
TC Gasket, 4", (3 pcs)
TC Gasket, 34mm DN20, 5-pack
The volume of the HopDrop Kit is 1.5L. Pellet capacity in weight will vary
BrewTool's solution to filtration of fermented beer. The filter kit is installed directly on the butterfly valve out of the fermenter.
The filter kit can also be used for other purposes and can be customized with many accessories and adapters.
If the filter clogs, simply remove one Tri Clamp and rinse it in sanitizer without further disassembly.
Normal use:
Assemble the filter kit and leave in sanitizer
Install the filter kit on the fermentation tank valve
Purge with Co2 a couple of times and relieve the pressure using the PRV
Open the valve, and let the air out using the PRV
Connect your ball lock connector to your keg or bottling setup
If used on hot side (over 140°F/60°C) we recommend replacing the Poly TC pipe and filter holder with stainless steel equivalents.
The filter kit can be doubled up and you can use a coarse and fine filter in combination using simple parts available as accessories.
More fittings using M16 threads can be used to extend or if you want to use 34mm TC on the filter output.
If you want to use it for TC 34mm or 1.5" we offer adapters to 2".
Included parts:
Ball lock adapter, 2", Liquid with M16 threads
3 pcs Filter, stainless steel 30mm, 300, 600 and 1000 micron
Filter holder made from food grade Nylon (PA), M16
TC 2" to 34mm Tee
TC 34mm Manual PRV
3 pcs 2" Tri Clamps
1 pcs 34mm Tri Clamp
2 pcs TC gasket with filter groove (blue)
1 pcs 2" Poly TC pipe, 200mm
2" and 34mm gaskets
An inline oxygenation kit designed to inject oxygen during transfer to fermenter.
We recommend placing a sight glass after the TC tee, to keep an eye on the O2 flow.
Requires an oxygen tank with a pressure regulator.
Included:
TC 34mm Tee
Barbed O2/CO2 stone holder, 6-10mm tube
O2/CO2 stone, 0.5micron. G1/8" threads
3 TC 34mm clamps
1 5-pack of TC 34mm gaskets
1 gasket for the stone
Laser cut filters made from steel blasted and electropolished stainless steel. Simple cleaning and maximum durability.
Gap width: 1.3mm
Pre-cut hole for weldless fitting to use with future accessories.
Laser cut filters made from steel blasted and electropolished stainless steel. Simple cleaning and maximum durability.
Gap width: 1.3mm
Pre-cut hole for weldless fitting to use with future accessories.
Laser cut filters made from steel blasted and electropolished stainless steel. Simple cleaning and maximum durability.
Gap width: 1.3mm
Pre-cut hole for weldless fitting to use with future accessories.
Cable for use between 2-pin cable and 24 VDC solenoid valves (gas).
Connector A: LP12, 2-pin male plug (in-line connector)
Connector B: DIN 43650 Form B
Color: Black
Length: 0.1m (3.9")
Adapter that allows connecting a power supply to a CAN device without FCS.
Connector A: LP12, 5-pin male plug (in-line connector)
Connector B: LP12, 5-pin female plug
Color: Black
Length: 0.1m
Cable for use between FCS I/O module and FCS relay module (5A).
Connector A: LP12, 7-pin male plug
Connector B: LP12, 7-pin female plug
Color: Black
Length: 3m (9.8 ft.)
M24 Threads to 34mm T.C. Adapter.
For the MiniUni+, this adapter can be used to replace the Pressure Kit spunding valve with a 34mm T.C. Elbow to install the FCS spunding assembly.
M16 x 1.5mm inside threads for accessories.
