The BrewBuilt SlingBlade is an innovative electric heating element designed to promote a rolling boil and even heat distribution. Shaped for Performance and Convenience The SlingBlade's unique crescent-shaped design positions all of the heating power on one side of the kettle, sending thermal energy upward to the surface that then cascades downward on the opposite side of the kettle. This movement creates a dynamic turbulence that evenly distributes heat while creating a vigorous, rolling boil. Other heating elements stick right out into the middle of the kettle or use a full circle design that rings the kettle wall. This can cause an obstruction for immersion chillers or make it difficult to stir without banging into the element. The SlingBlade was designed to avoid these issues. By remaining on one side of the kettle, the element will be out of the way of your immersion chiller, and since the element follows the curvature of the kettle wall, it won't interfere with the flow of wort during whirlpool. Ultra-Low Watt Density An electric element transfers power to your wort by applying heat, but if this heat is too concentrated you will get local heating that is hotter than 212°F. This catalyzes Maillard Reactions, which can lead to darker beer than intended and produce unwanted caramelization. Think of these reactions like roasting a marshmallow. First it gets a light brown, we call this Maillard reactions, a little hotter and it gets a dark brown, we call this caramelization, then it turns black and we call this pyrolysis (burnt or scorched). While all kettles undergo these reactions, an electric element can concentrate more heat into a small area, which can quickly scorch your wort. Our experience is that at 90-watts per square inch recipes need to be modified to account for the element and light beers never come out quite right. The SlingBlade element was designed at 50-watts per square inch to reduce the chance of scorching while still providing a vigorous boil. For even lower watt density, consider the Boil Vigor Controller. Tri-Clamp Connection The SlingBlade installs quickly and easily on any kettle with a T.C. ferrule thanks to the curved, non-circular design. This also makes it a breeze to remove the element for cleaning between uses. The SlingBlade heating elements were designed to fit perfectly with BrewBuilt brewing kettles, but you may find them suitable for other kettles as well. They should be used with T.C. ferrules no longer than 1" in length. For dimensions and recommended minimum kettle diameter, please see the chart below. Features: Made from Incoloy alloy with proprietary coating for long life 1.5" Tri-Clamp connection Unique offset design promotes rolling boil Ultra-Low Watt Density eliminates scorching UL Certified components Specs: 240 Volt L6-30 plug 20 Amp breaker required for 10 & 15 gal element 30 Amp breaker required for 22 & 31 gal element 50-gallon kettle requires 2 x BE538 and 2 x 30 amp circuits SKU Kettle Vol. Wattage Length Radius Min. Kettle Ø BE535 10 gal 3750 13.25" 6.3" 13.78" BE536 15 gal 4500 16.75" 7.3" 15.75" BE537 22 gal 5000 17.25" 8.3" 17.72" BE538 31 gal 5750 19.5" 9.3" 19.69" Please note: Length is measured from the tip of the heating element to the T.C. connection. Radius is measured from the middle of the T.C. connection to the outermost edge of the element's curve. ***In order to avoid injury or death we strongly recommend using a GFCI in any circuit used near water. You can find one here.*** Lowest Price Guarantee, this item has MAP pricing so you can be confident you won't find it for less.
Keep an eye on your temps with the BrewBuilt tri-clamp thermometer. Perfect for stainless conical fermenters or T.C. kettles. The 3" diameter dial face is easy to read and scaled in °F and °C. The 6" probe length provides the thermometer with plenty of exposure for more accurate readings.
3" dial face
6" probe
1.5" T.C.
Reads in °F and °C
Keep an eye on your temps with the BrewBuilt tri-clamp thermometer. Perfect for stainless conical fermenters or T.C. kettles. The 3" diameter dial face is easy to read and scaled in °F and °C. The 2" probe length will stay clear of other fermentation or brewing accessories.
3" dial face
2" probe
1.5" T.C.
Reads in °F and °C
Due to high demand, this item is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this to you when we receive more inventory.
Don't fear the Beast, feed the Beast! This heavy duty counterflow wort chiller will gobble up heat from your wort as it passes from kettle to fermenter so you can pitch your yeast as soon as possible. Made from passivated 304 stainless steel, The Beast has a 30 ft. wort line with 1.5" T.C. connections and a 29.5 ft. coolant line with 1/2" male BSPT connections. Tri-clamp connections offer the most sanitary way to pass wort through your heat exchanger and pairs perfectly with BrewBuilt's line of T.C. Kettles and X1 Uni Conical Fermenters. The BSP coolant connections work well with Camlock, Duotight, NPT or other BSP fittings found below. Adding a ball valve to the coolant line inlet is a great way to dial in flow for maximum cooling efficiency!
When it comes to counterflow chillers, we love the coil design for its ease-of-use. Plate chillers are great for their high efficiency and compact size, but if there's too much hop matter running through them, they can quickly clog up. Transferring wort from your kettle to your fermenter is one of the critical steps in the brewing process where you don't want any hiccups. The Beast's wort line is 1/2" ID so it can withstand high amounts of hop additions without clogging!
A cross bar is welded on one side of the coil with pre-drilled mounting holes allowing it to be easily installed under your work bench or mounted directly to your brewing system.
Specs:
Beer Line: 30 ft. long
Beer Connection: 1.5" tri-clamp
Coolant Line: 29.5 ft. long
Coolant Connection: 1/2" BSPT
Crossbar with pre-drilled mounting holes (4mm)
Made from 304 stainless steel
Replacement Gaskets for your BrewBuilt Mash Tun. These are custom pieces we've designed for the BrewBuilt Mash tuns. Their only purpose? Assist you in brewing the best beer possible. Solid single piece silicone molded construction will last you for a number of brews, but whether you lose yours, or manage to break it, we have replacements. For a complete False Bottom Kit that includes the necessary Screen and Pickup Tube, see our BrewBuilt Mash Tun False Bottom Kits. Or for a complete Mash Tun, see our BrewBuilt Mash Tuns. Lowest Price Guarantee, this item has MAP pricing so you can be confident you won't find it for less.
The BrewBuilt Whirlpool Return Fitting allows you to recirculate wort in your boil kettle without sacrificing one of your tri-clamp ports. Install it in any tri-clamp kettle's thermometer port and attach your preferred valve to the side inlet. The front of the fitting can be capped off with a 1.5" T.C. end cap, or you can pair with the BrewBuilt Thermowell Offset to install a thermometer or temperature probe.
BrewBuilt Bi-Metal Thermometers are top-of-the-line measuring instruments, made in the USA by Tel-Tru manufacturing. Maintain the overall precision of your brew system with these incredibly accurate and generally superior thermometers. These are produced according to strict standards, comparable to ISO9000 quality, and are set up with an 8 year manufacturers warranty boasting that quality.
Bi-metal thermometers are the level of quality you want when a few degree difference results in a completely different malt profile on your beer. While a bit more expensive, you won't ever mess up a batch because of incorrect temperature readings. The 2.5" Stem is a perfect balance of being long enough to get accurate readings, while not protruding far enough to get hit by a wandering mash paddle or spoon.
Are all bi-metal thermometers created equal? Not really. The problem with most bi-metal thermometers is that hang ups occur and you have to tap the thermometer to get an accurate reading. The cause of the problem is that the bimetallic helical coil in the stem of other bi-metal thermometers is tack welded to the stem itself. Our new line of thermometers feature a super sensitive bimetallic helical coil suspended from a copper coated bushing fixed in the stem.
This superior design provides a faster response to temperature changes and assures more accurate readings. What does this mean? You don't have to tap the gauge with your finger as much.
They are also accurate to 1% of the total range, feature a polished 3" 304 s/s housing, a hermetically sealed water proof case, glass face, external calibration capabilities, and a unique anti-parallax dial that provides for easy reading. The reading is actually taken from the last 2.5" of the probe.
Features:
Large 3" Dial Face for easy readings
2.5" Stem perfect for Boil Kettles and HLTs
High Grade Stainless Steel Construction and hermetically sealed casing
Can be calibrated with 1/16" Allen Wrench (Though should never be needed)
Dual Scale Range: 0-220° F, -10 to 100° C
Back Connection is 1/2" MPT, stem is 1/4" SS
8 year Manufacturer Warranty
Having your pump securely mounted where you want it gives you a more stable unit that is easier to control.
With this stainless mounting bracket you can mount your pump right where you want it in your brewing setup. It has two pre-drilled holes so you can attach it to a brewing stand, cart, etc. After you have secured the mounting bracket you can easily slide your pump into place and remove it when you're finished, if desired. Keep your brew system tidier during brewing by giving your pump a dedicated mount to keep it out of the way.
Fits our Chugger Pumps (H331 and H332).
Due to high demand, this item is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this to you when we receive more inventory.
The easiest way to power the BrewBuilt™ SlingBlade! This professionally wired watertight switch gives you a simple On/Off control of your heating element. Switches both legs of a 220V 30AMP circuit and comes with 5 ft. input and output cords with molded LP6-30P ends. It also features two handy tabs for mounting to a wall.
Don't wear out your expensive plugs and sockets hot patching your 220V burner elements. Plugging your element directly into a live power outlet will cause a small spark, and when done repeatedly this can damage the plug and the socket, especially with high voltage 220V appliances. Not only is the power switch more convenient to turn your element on and off during the brew day, it will eliminate the risk of damage done by hot patching.
BrewBuilt Bi-Metal Thermometers are top-of-the-line measuring instruments, made in the USA by Tel-Tru manufacturing. Maintain the overall precision of your brew system with these incredibly accurate and generally superior thermometers. These are produced according to strict standards, comparable to ISO9000 quality, and are set up with an 8 year manufacturers warranty boasting that quality.
Bi-metal thermometers are the level of quality you want when a few degree difference results in a completely different malt profile on your beer. While a bit more expensive, you won't ever mess up a batch because of incorrect temperature readings. The 6" Stem here is perfect for Mash Tuns, as it will reach further into the mash to get a more representative reading.
Are all bi-metal thermometers created equal? Not really. The problem with most bi-metal thermometers is that hang ups occur and you have to tap the thermometer to get an accurate reading. The cause of the problem is that the bimetallic helical coil in the stem of other bi-metal thermometers is tack welded to the stem itself. Our new line of thermometers feature a super sensitive bimetallic helical coil suspended from a copper coated bushing fixed in the stem.
This superior design provides a faster response to temperature changes and assures more accurate readings. What does this mean? You don't have to tap the gauge with your finger as much.
They are also accurate to 1% of the total range, feature a polished 3" 304 s/s housing, a hermetically sealed water proof case, glass face, external calibration capabilities, and a unique anti-parallax dial that provides for easy reading. The reading is actually taken from the last 2.5" of the probe.
Features:
Large 3" Dial Face for easy readings
6" Stem perfect for Boil Kettles and HLTs
High Grade Stainless Steel Construction and hermetically sealed casing
Can be calibrated with 1/16" Allen Wrench (Though should never be needed)
Dual Scale Range: 0-220° F, -10 to 100° C
Back Connection is 1/2" MPT, stem is 1/4" SS
8 year Manufacturer Warranty
This unique thermowell fitting is has the probe offset from the center of the fitting, leaving room for additional hardware such as the BrewBuilt Whirlpool Return Fitting. Pairing the two fittings allows you to recirculate wort in your boil kettle while still getting temperature readings from your thermometer or temperature probe. The thermowell has a 6" probe that fits all BrewBuilt kettles so that you can get the most accurate temperature measurement of your wort.
Due to high demand, this item is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this to you when we receive more inventory. 304 stainless steel splash resistant construction Industrial design using commericial quality components for long life and easy serviceability Digital power reading for precise repeatability. No more guessing if you found the sweet spot on the dial Outlet fully disconnected when powered off for added safety, unlike some one-leg designs Linear power control for better repeatability at low power settings Wall mount bracket allows you to get the controller off the table and out of the way Dial your brew day up to 11 with the BrewBuilt™ Boil Vigor Controller! This controller allows you to control the current of a 208-240V heating element up to 30 amps. Perfect for dialing in your boil vigor for more consistent boil-off rates or adjusting the heat input to a still wash pot. The controller works by adjusting the percentage of power delivered to the heating element. The power is increased in a linear fashion from 0 to 100% as you adjust the dial from 1 to 11. Features industrial-style power switch, dial knob, and digital amm meter mounted on a splash resistant stainless steel enclosure. Pre-cut mounting holes allow you to hang the controller on your brew stand on the wall at eye-level. We highly recommend mounting the controller so you don't have to worry about keeping an area of your table dry where you might lay it down. L6-30 connections with 4 ft. cords on either end. Compatible with all 208-240V elements 30 amps and lower. While L6-30 are the most common elements available, yours may need an adapter. The Boil Vigor Controller uses a generously overrated SSR with a very large fan-cooled heatsink for better reliability. An SSR's life expectancy is directly related to its operating temperature, and this unit is built with the lowest Q heat dissipation system offered at the homebrewing level. It includes a contactor to fully shut off both legs when you throw the power switch, making the free end of the cord safer when the element is not plugged in. The display gives you a reading of the actual current being consumed by your element in Amps. On some systems, a small change in the adjustment makes a large current change at the element, especially at lower settings used during hop stands and distillation. The BrewBuilt controller provides a linear control and a digital readout to eliminate the guessing, allowing you to focus on your process and not your equipment. If you'd prefer not to mount the controller to your wall, consider the stainless steel Controller Stand. **Caution: In order to avoid injury or death we strongly recommend using a GFCI in any circuit used near water. You can find one here.**
Kettle Maximizer allows you to pull liquor or wort from below the depth of your kettle's bottom port
Angle straight down in hot liquor tanks to maximize pick up
Rotate to your preferred pick-up height in boil kettles to leave trub behind when transferring to fermenter
The tri-clamp maximizer is recommended for boil kettles and hot liquor tanks with 1.5" T.C. bottom ports. This fitting will allow you to pull liquor or wort from below the depth of your kettle's bottom port without the need to tip your vessel. For hot liquor tanks, point the end of the tube straight down to maximize pick up. For boil kettles, you can rotate the maximizer to position the end of the tube at your preferred height above the bottom of the kettle, leaving room for a layer of trub that will be left behind in the kettle when you transfer wort to your fermenter.
1.5" tri-clamp
Tube Length: 6.5"
Overall Length: 8.18"
Made from stainless steel
Perfect for powering 230V / 30 amp electric elements, power controllers and brewing systems away from your main wall socket. Comes with male and female L6-30 sockets on either end. 10 feet long. Do Not string multiple cords together for a longer length.
Due to high demand, this item is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this to you when we receive more inventory.
304 stainless steel splash resistant construction
Industrial design using commercial quality components for long life and easy serviceability
On/Off thermostat control
Outlet fully disconnected when powered off for added safety, unlike some one-leg designs
Wall mount bracket allows you to get the controller off the table and out of the way
Keep your temps tight with the BrewBuilt™ HLT Controller! Perfect for keeping your sparge water or mash water at your set temperature—it allows you to control a 208-240V heating element up to 30 amps based on temperature. The controller works by turning the burner power on and off at 100% power until it reaches the temperature setpoint. Features industrial-style power switches, and a 1/6 DIN Controller mounted on a splash resistant stainless steel enclosure. Pre-cut mounting holes allow you to hang the controller on your brew stand on the wall at eye-level. We highly recommend mounting the controller so you don't have to worry about keeping an area of your table dry where you might lay it down. L6-30 connections with 4 ft. cords on either end. Compatible with all 208-240V elements 30 amps and lower. While L6-30 are the most common elements available, yours may need an adapter. Uses a 9' stainless braided PT-100 temperature sensor.
The HLT Controller includes a contactor to fully shut off both legs when you throw the power switch, making the free end of the cord safer when the element is not plugged in.
If you'd prefer not to mount the controller to your wall, consider the stainless steel Controller Stand.
**Caution: In order to avoid injury or death we strongly recommend using a GFCI in any circuit used near water. You can find one here.**
Convert the BrewBuilt T.C. brewing kettle into a mash tun using one of these false bottom kits. The heavy duty false bottom rests low in the kettle, utilizing a tri-clamp style maximizer that reduces dead space and pulls from the very bottom of your kettle, leaving no wort behind. A Silicone gasket rims the False Bottom, ensuring a tight seal to the wall with no chance of grain bypass. A handle is welded to the top of the false bottom for easy removal. To monitor your mash temperature, we recommend the 1.5" T.C. Thermometer with 6" probe for better grain bed penetration. 1.5" tri-clamp and gasket included Welded T.C. maximizer False bottom gasket for tight seal Welded legs and handle Made from 304 stainless steel NOTE: These false bottom kits will fit all BrewBuilt T.C. kettles, including the electric kettle with SlingBlade heating element. We do not recommend converting the electric kettle into a mash tun as the element will scorch the grain. If you wish to use the false bottom in your boil kettle, it should be noted that the screen is designed to filter grain, so fine particle vegetal matter will pass through.
Recirculate wort in your boil kettle without sacrificing one of your tri-clamp ports. The BrewBuilt Whirlpool Return Fitting & Thermowell Offset kit allows you to use any tri-clamp kettle's thermometer port to recirculate wort while also taking temp readings. This kit is perfect for kettles that only have two tri-clamp ports—eliminating the need to drill out a hole in your kettle to add a third port for wort recirculation. Attach your preferred valve or tri-clamp fitting to the side inlet and, during whirlpool, draw wort from your bottom port and pump it back through the Whirlpool Return Fitting.
Kit Includes:
Whirlpool Return Fitting
Thermowell Offset
(1) 1.5" Tri-Clamp
(1) 1.5" Tri-Clamp Gasket (EPDM)
Made specifically for whirlpooling, this fitting angles ricrculating wort along the kettle wall for a more efficient whirlpool effect
Doubles as a kettle maximizer, allowing you to pull wort from below the depth of your kettle's bottom port
Rotate to your preferred pick-up height in the kettle to leave trub behind when transferring to fermenter
Compatible with kettles 12" in diameter and larger
This unique tri-clamp fitting works perfectly for whirlpooling hops at the end of the boil and doubles as kettle maximizer when transferring out to your fermenter. When recirculating wort through the bottom port, wort will be returned to flow along the kettle wall for a more efficient whirlpool effect, drawing vegetal matter into the center of your kettle. When transferring wort out, the fitting will then pull from the side of the kettle where matter has been cleared, and by angling the end of the tube downwards, you'll be able to pull liquid from below the depth of your kettle's bottom port without the need to tip your vessel.
1.5" tri-clamp
Length from T.C. to tube bend: 7" (approx.)
Length from tube bend to outlet: 9" (approx.)
Made from stainless steel
Ball Valve hardware pack for the BrewBuilt Brewing Kettle with 2 x tri-clamp ports. Includes ball valve and hardware for connecting tubing at the kettle's bottom port. End cap included to seal the top port if a thermometer or other accessory is not in place.
Includes:
(1) Stainless 3-Piece Ball Valve - 1.5" T.C. x 1/2" FPT
(1) Stainless 1/2" MPT x 5/8" Barb Adapter
(2) Stainless 1.5" Tri-Clamp
(2) EPDM 1.5" Tri-Clamp Gasket
(1) Stainless 1.5" End Cap
Teflon Tape
Filter hops, grains, coffee grounds, and other kettle additions
Screen sits tight to the edges with the included BrewBuilt silicone screen gasket
All stainless welded components with handle for easy install and removal
The BrewBuilt Kettle Screen fits perfectly in the BrewBuilt Brewing Kettle and can be used to filter hop additions, convert the kettle into a mash tun, or for making large batches of cold brew coffee. The welded stainless steel flat bar feet sit on the bottom of your kettle and positions the screen approximately 3/8" above the kettle's bottom port. The silicone gasket creates a tight seal around the kettle wall to retain solids above the screen when transferring liquid out of the kettle.
Ball Valve hardware pack for the BrewBuilt Brewing Kettle with 2 x tri-clamp ports. Includes ball valve and hardware for connecting tubing at the kettle's bottom port. End cap included to seal the top port if a thermometer or other accessory is not in place.
Includes:
(1) Stainless 1.5" Tri-Clamp 3-Piece Ball Valve
(1) Stainless 1.5" Tri-Clamp x 1/2" Barb Adapter
(3) Stainless 1.5" Tri-Clamp
(3) EPDM 1.5" Tri-Clamp Gasket
(1) Stainess 1.5" End Cap
Precision Fit: Engineered to perfectly match the internal dimensions of your BrewBuilt draining kettle.
Optimal Flow: The fine perforations allow for excellent liquid drainage without letting grain particles through.
Durable Construction: Made from high-quality, corrosion-resistant stainless steel for a long service life.
Easy to Use: Simple to install, remove, and clean, making your brew day more efficient.
Achieve crystal-clear wort and a smoother brew day with the BrewBuilt False Bottom. Designed specifically for our draining kettles, this precision-engineered false bottom creates a secure barrier between your mash and your kettle's drain port.
The perforated stainless steel design allows liquid to pass through freely while keeping all your grains contained. This prevents clogs and ensures efficient lautering, giving you maximum yield and a brilliantly clear wort every time. The integrated feet provide the perfect clearance, and the durable, food-grade stainless steel construction is easy to install and even easier to clean. Upgrade your BrewBuilt draining kettle and take the hassle out of lautering.
Butterfly Valve hardware pack for the BrewBuilt Brewing Kettle with 2 x tri-clamp ports. Includes butterly valve and hardware for connecting tubing at the kettle's bottom port. End cap included to seal the top port if a thermometer or other accessory is not in place.
Includes:
(1) Stainless 1.5" Tri-Clamp Butterfly Valve
(1) Stainless 1.5" Tri-Clamp x 1/2" Barb Adapter
(3) Stainless 1.5" Tri-Clamp
(3) EPDM 1.5" Tri-Clamp Gasket
(1) Stainless 1.5" End Cap
Integrated 2" TC Port: Seamlessly connect a condenser or still top to recover hop oils, distill water, or experiment with spirits, transforming your kettle into a versatile system.
Optimal Vapor Collection: The raised dome design facilitates efficient vapor collection and separation, ensuring high-quality distillation and enhanced performance.
Secure & Durable Design: Crafted for a precise fit and a secure seal, this domed lid ensures optimal function and lasting durability for all your brewing and distilling needs.
Bring your brewing to the next level with the BrewBuilt Domed Lid for Dish Bottom Kettles. This essential upgrade features a centered 2" tri-clamp (TC) port, giving you the flexibility to easily add a condenser or still top.
Whether you're looking to recover hop oils, distill water, or experiment with spirits, this domed lid is designed for a seamless fit and optimal performance. The raised dome design allows for proper vapor collection and separation, while the high-quality construction ensures a secure seal. Transform your BrewBuilt kettle into a multi-functional powerhouse and unlock a new world of brewing possibilities.
Effortless Grain Removal: Simply attach the stainless steel chute to the integrated grain door on your BrewBuilt Dish Bottom Mash Tun for a clean and controlled way to empty spent grains directly into a bucket.
Mess-Free Brewing: This essential upgrade eliminates spills and reduces cleanup time, ensuring a quicker and more efficient post-brew day process.
Durable and Sanitary Design: Constructed from durable, food-grade stainless steel, the grain chute is built to last and is easy to clean, maintaining a sanitary environment for your brewing process.
Tired of messy grain removal? The BrewBuilt Grain Chute is the essential upgrade for your BrewBuilt Dish Bottom Mash Tun. Designed to fit the integrated grain door, this chute provides a clean and controlled way to remove spent grains.
Simply attach the stainless steel chute to the grain door and use a rake or paddle to push the grain directly into a bucket or disposal bag. This simple addition eliminates spills on the floor, reduces cleanup time, and makes grain removal quick and efficient.
Crafted from durable, food-grade stainless steel, the BrewBuilt Grain Chute is built to last and easy to clean. Get yours and make your next brew day a little less messy.
Eliminate Steam and Condensation: The condenser's continuous flow of cool water captures and converts hot steam back into a liquid that can be easily drained, keeping your brewing area dry and free of moisture damage.
Simple, Secure Connection: The condenser attaches directly to a 2" TC port on your BrewBuilt Domed Lid, creating a fully contained, steam-free brewing system.
Durable, Sanitary Construction: Made entirely of stainless steel with a tri-clamp connection, this high-efficiency unit is built to last and provides a clean, secure way to get a full rolling boil anywhere.
Brew indoors without the worry of moisture, mold, and humidity. The BrewBuilt Condenser is your ultimate solution for a steam-free brew day. This high-efficiency unit is designed to attach directly to the 2" TC port on your BrewBuilt Domed Lid, turning your kettle into a fully contained system.
Using a continuous flow of cool water, the condenser captures and converts hot steam back into liquid, which can then be drained away. Its durable all-stainless steel construction and tri-clamp connection provide a clean, secure way to eliminate steam and its associated cleanup. Now you can get a full, rolling boil anywhere—without turning your brewery into a sauna.
