This replacement spring is intended for use with our adjustable stainless steeel pressure relief valve - D1832L & D1833L. These units are adjustable from 0 to 30 psi. Example photo shown. The spring you receive may not match the photo exactly.
This Thermal Printer Ribbon is a replacement for the ribbon supplied on the Semi-Automatic Label Applicator Machine. ID: 25mm OD: 63mm Ribbon Width: 30mm Ribbon Length: 100m KegLand Part Number: KL20336
In case yours got too close to the flame on your brewing system. Probes can also be damaged by kinking which will cause a controller to give an inaccurate, high, reading. This is a replacement wire and thermistor for our line of Ranco controllers. The sensor probe is 1/4 in diameter and works well with the Stopper or Coupler Thermowells. Temperature Range of -30 to 220F. 8 ft. long.
Probes are water-resistant, but not water proof.
Weldless Pressure Relief Valve for Chronical series fermenters. This is a standard replacement for the 1/2 barrel Chronical but can also be retrofitted to work on the 7 gallon Chronical fermenter. The unit releases between 5-6 psi.
A replacement pull-ring style relief valve for your favorite keg!
This is the most common relief valve. Fits most Cornelius and Firestone style kegs, along with many others. Features a long body with spring, and gray top with pull ring.
Max. pressure rating: 100 psi
Kegland Part Number: KL03070
Replacement pressure relief valve rated to blow at 65 psi. This is a direct replacement of the PRV featured on the KOMOS® CO2 regulator. The Green PRV can also be used with pressurizable FermZilla models for hydro testing. Note that under normal operation, the FermZilla should always be used with the Red PRV.
Replacement pressure relief valve rated to blow at 35 psi. This is a direct replacement of the PRV featured on the FermZilla and Kegmenter. It is also compatible with homebrew kegs and the KOMOS® CO2 regulator if you desire a lower blowoff pressure.
Corny keg style pressure relief valve rater to 17 PSI
Lower the blow off pressure of kegs, regulators, fermenters, etc. for added operating safety
Replacement pressure relief valve rated to blow at 17 psi. This corny keg lid style PRV can be used with a range of products including kegs, FermZilla conicals, KegLand kegmenters, and KOMOS CO2 regulators. If you don't intend to ever exceed 17 PSI with the product you're using, installing the Yellow PRV will help ensure you don't over pressurize.
NOTE: This is a safety device designed to release pressure at the approximate rated pressure. This is not intended to be used as a Spunding Valve.
KegLand Part Number: KL22569
This pump is a direct replacement for the standard stainless centrifugal pump that comes included with our 20x20cm plate and frame filters. 110v Single Phase. Please note that while this pump is physically very similar to our PMP100 Stainless Centrifugal Pump, the electric motor is not as powerful and this is not meant to be a substitute for the PMP100.
Compatible with WE903,WE905,WE906N,WE908N
Replacement 6W high temperature magnetic drive pump for 220V Gen 4 BrewZillas. Compatible with 35L & 65L units.
This pump is not backwards compatible with Gen 3 or older units.
KegLand Part Number: KL24341
Replacement pump assembly for any variable volume fermenter. Includes built-in gauge and line to connect with gasket, but does not include gasket. Made in Italy.
Replacement pump for the Speidel Braumeister Electric Brewery. This is the newest unit now being used in the 2021 models, but is also backwards compatible with older generations.
Stainless steel pump assembly for any variable volume fermenter. Includes built-in gauge and line to connect with gasket, but does not include gasket. Made by Speidel of Germany, this stainless pump is made to a higher quality than comparable replacment pumps made in Italy.
A replacement pump head for the H308 diaphragm pump, should the diaphragms become worn or get damaged by passing particulate matter through them.
Please Note: This pump head does not include the Pre-Filter or the Elbow fittings that are connected to your hoses, those will need to be transferred over from the existing pump head or purchased separately.
Replacement plastic pump head for the MKII High Temperature Magnetic Pump (PMP50). If you're replacing a broken head on your MKII pump, also consider these stainless steel upgrades—standard stainless center inlet head or stainless inline tri-clamp head. Kegland Part Number: KL13536
Replacement RAPT Controller for 35L Gen 4 BrewZillas. Compatible with all Gen 4 models. This will not work with BrewZilla Gen 3.1.1 models or older. It is also not suitable for DigiBoil units.
Please refer to the instruction manual on adjusting the controller between the Gen 4 units. There is a mechanical toggle switch on the back of the board that will need to be adjusted.
KegLand Part Number: KL20305
Replacement RAPT Controller for 65L Gen 4 BrewZillas. Compatible with all Gen 4 models. This will not work with BrewZilla Gen 3.1.1 models or older. It is also not suitable for DigiBoil units.
Please refer to the instruction manual on adjusting the controller between the Gen 4 units. There is a mechanical toggle switch on the back of the board that will need to be adjusted.
KegLand Part Number: KL20305
A replacement lid for the rear overflow reservoir on the Enolmatic filler. Includes the float assembly which breaks the vacuum and stops filling if the reservoir becomes full to prevent messy overflowing.
Replacement RO membrane for the BrewRO System. The RO membrane should be changed every 3 years.
Only use HbrewO replacement filters on your BrewRO System, failure to do so can damage the system.
This is a replacement silicone elbow bend for 35L or 65L BrewZillas. Compatible with Gen 3 and Gen 4. This part joins the pump to the inlet on the base of the BrewZilla then to the outlet of the pump to the recirculation arm on the side of the BrewZilla.
Made from food grade silicone. Temperature resistant to 356°F (180°C).
KegLand Part Number: KL06293
Replacement Rocker Switch for BrewZilla / DigiBoil. Compatible with all DigiBoils and Gen 3.1 or older BrewZillas.
Compatible with 110-120V and 220-240V.
KegLand Part Number: KL05968
Replaces the rubber airlock stopper that comes with our Speidel plastic tanks.
Does Not include the airlock shown in the photo.
Stopper height: 1 3/8". Upper diameter 1 3/4". Lower diameter 1 7/16". Inner diameter 11/16".
Color may vary.
KegLand's 500ml Amber PET bottles come with reusable screw caps, but these replacements are available if you prefer to use new caps with each bottling run. The locking ring is left behind on the bottle neck the first time the cap is screwed off, so if you're using fresh caps you'll want to remove the locking ring from the previous cap. These caps can also be used to replace the threaded caps included on the lid of the FermZilla fermenter. KegLand Part Number: KL25881
Contains the o-rings for the piston, the red inlet washer, MK4 seat assembly o-ring, 2 x barb MFL outlet o-rings and a thumb screw o-ring.
For instructions on replacing the seals and/or general maintenance please refer to the product manual below.
KegLand Part Number: KL12584
Replacement seal for the main shaft of the fill spout on our WE670 and WE643 Professional Wine Bottle Fillers. This is the cone that the bottle opening seats against to seal the system during filling.
Replacement sediment filter for the BrewRO System. The sediment filter should be changed every 6 to 12 months depending on usage.
Only use HbrewO replacement filters on your BrewRO System, failure to do so can damage the system.
