A Pressure Relief Valve upgrade or replacement for the Chronical line of fermenters from Ss BrewTech.
Features:
Standard replacement part for Half Barrel
Can be retrofitted to 7 Gal Chronical lid
Releases pressure between 2-2.5 psi
Food grade silicone O-ring
Use Dewalt DWA1783IR step bit for retrofit
For 7/32" inch hole diameter (in lid)
The HI84500-62 are packets of stabilizer reagent required for determination of sulfur dioxide in wine using the HI84500 Sulfur Dioxide Mini Titrator for Wine Analysis. The HI84500 mini titrator uses two different titrant solutions that contain different concentrations of potassium iodate to measure a wide range of sulfur dioxide concentration in wine. Both low and high range measurements require the addition of HI84500-62 stabilizer powder to convert iodate into iodine, which in turn reacts with sulfur dioxide. The HI84500-62 powder is packaged into single use packets that are emptied into the sample prior to performing the titration.
Pre-measured packets
Clearly marked expiration date and lot number
The HI84500-62 stabilizer powder packets are necessary to convert the iodate titrant into iodine. The iodine then reacts with sulfur dioxide and the HI3148B ORP electrode is used to detect the endpoint for both the low (1.0 to 40.0 ppm of SO2) and high (30 to 400 ppm of SO2) ranges. The decision by Hanna to use the HI84500-62 stabilizer powder packets and iodate titrant in place of a iodine titrant is due to shelf stability. Iodate offers much greater shelf stability than iodine. By using stabilizer packets the titrant solutions remain stable for longer periods of time.The HI84500 can be used with all wines, including red, which are difficult to test using traditional methods due to the difficulty to observe a distinctive color change when the endpoint is reached.
The HI84500 determines the free and total sulfur dioxide concentration in wine using the Ripper method. Excess iodide is added to the wine sample and reacts with the iodate titrant to produce iodine:
IO3- + 5I- + 6H+ → 3I2 + 3H2O
The iodine produced reacts with sulfur dioxide in the wine according to the redox reaction below:
H2SO3 + I2 → H2SO4 + 2HI
Replacement reagents required to operate the HI84500 include:
Low Range - 1.0 to 40.0 ppm of SO2
High Range - 30 to 400 ppm of SO2
Pump calibration standard
HI84500-55
HI84500-55
Titrant solution
HI84500-50
HI84500-51
Acid reagent
HI84500-60
HI84500-60
Alkaline reagent (Total SO2)
HI84500-61
HI84500-61
Stabilizer powder packets
HI84500-62
HI84500-62
Convert 3/4" BSPP (Straight Thread) fittings to 1.5" Tri-Clover. Often used on 20x20 plate filters, where the stock 3/4" barbed inlet and outlet fittings are replaced with these to convert to 1.5" Tri-Clover. Use along with our H928 o-ring to form a seal on the straight threads.
Stainless - 1/4 in 3 Way Ball Valve - FPT x MPT x FPT
Please Note: Valves include a Teflon gasket. Do not soak the valves in PBW which can corrode Teflon material after prolonged contact.
Our Ball Valves will last for years. Easy to clean. High grade 304-stainless made to last. 1/4" FPT on input and output side.
TIP: You can take a ball valve apart using two crescent wrenches. This will allow you to open up the valve to get to the ball and two gaskets that form the seal when closed. Here at MoreFlavor! we think this ball valve is actually easier to clean than 3-piece ball valves (such as our H602D).
This is a Stainless Steel one way Check Valve. It has 2" T.C. Fittings on either side, and releases pressure at ~1 p.s.i.
Can be used to inhibit a siphon in certain applications, or to vent gas pressure in a tank.
This attachement can be used to replace the spigot or the airlock on your Speidel plastic fermenter and give you a 1/2 in. MPT to the outside and a 1/2 in. FPT on the inside. This allows you to attach a variety of components on the inside and outside of your fermenter. This coupling uses the standard speidel lock ring and gasket.
Stainless steel 3 way ball valve with 1/2" female BSP at all ends. The T Port configuration has multiple open and closed positions. Please refer to see the function of each handle position.
KegLand Part Number: KL15882
This is the same fitting we use in our kettles. Designed with internal 1/2" FPT threading to accomodate diverters or maximizers, and outer 1/2" MPT threads for affixing a ball valve.
Our Ball Valves will last for years. Easy to clean. High grade 304-stainless made to last. 1" FPT on input and output side.
TIP: You can take a ball valve apart using two crescent wrenches. This will allow you to open up the valve to get to the ball and two gaskets that form the seal when closed.
Please Note: the ball valve may be difficult to turn at first, but it will become less resistant after it is rotated back and forth a couple times.
Need a ball valve with a TC connection? Ss Brewtech has got you covered! This 1/2 in ball valve has 1.5 in TC on one side, and 1/2 in female NPT on the other. It is perfect for Ss Brewtech BME kettles as a tangential inlet.
Features:
3 piece body
Made from 304 stainless steel
1/2 in ID valve body
1.5 in TC
1/2 in. female NPT
304 grade stainless steel ball valve. Full port for maximum flow rate. 1,000 psi rating for water, oil, or gas.
1/2" BSP female threads at inlet and outlet.
KegLand Part Number: KL03681
304 Stainless steel, full port, two piece ball valves that will last for years. Easy to clean with 1/2" FPT on input and output.. High grade 304-stainless made to last with1000psi rating. We've been selling these same valves from the same manufacturer for over 10 years. This is non-locking valve meaning that it does not come with the locking clip. Many users prefer this because you are not constantly lifting the clip to open and close the valve. If you would prefer a ball valve with a locking clip please see the Brewbuilt Ball Valve.
TIP: You can take a ball valve apart using two crescent wrenches. This will allow you to open up the valve to get to the ball and the two PTFE gaskets that form the seal when closed.
Our Ball Valves will last for years. Easy to clean. High grade 304-stainless made to last. 3/4" FPT on input and output side.
TIP: You can take a ball valve apart using two crescent wrenches. This will allow you to open up the valve to get to the ball and two gaskets that form the seal when closed.
Our Ball Valves will last for years. Easy to clean. High grade 304-stainless made to last. 3/8" FPT on input and output side.
TIP: You can take a ball valve apart using two crescent wrenches. This will allow you to open up the valve to get to the ball and two gaskets that form the seal when closed.
This ball valve with male and Female Beer Thread (5/8" BSP) is incredibly handy for those wanting to shut off flow of liquid and gas lines on keg couplers or shanks. Highly recommended if you are disconnecting your coupler and not re-attaching to another keg immediately. Made from 304 stainless steel.
Kegland Part number: KL00406
This stainless ball valve has a PCO 1881 female thread on one side for attaching to the male thread on the FermZilla lid or collection container and a 3/4" BSP Female thread on the other side for attaching other fittings.
The 20mm bore (approx.) makes it possible to perform low oxygen dry hopping through the ball valve.
Use this valve with a standard soda bottle as an inexpensive and effective dry hopping solution Attaches to the PCO 1881 threaded port on the FermZilla fermenter's lid Carbonation Cap and Tee Piece can be added to allow for purging the hops with CO2 This really handy stainless adapter ball valve will enable you to connect two PCO 1881 threads with a valve in between. Each side has an integrated O-ring that will seal on the neck of the PCO1881 Thread. Ideally suited to making a dry hop device for FermZilla with a standard soda bottle or PET growler with PCO 1881 threaded neck. As shown in the photo, if you use this stainless ball valve in conjunction with the PCO 1881 Tee Piece and the Carbonation Cap, you will have the added advantage of being able to use CO2 to purge out oxygen from the hops before you dry hop. This assembly makes an inexpensive and very effective dry hopping tool. Please note: Dry hop pellets will require a bit of a shake to get them to fall through the 3/4" bore. Tapping the PET bottle should be enough to make the hops fall down into the fermenter through the ball valve. KegLand Part Number: KL18074
This Stainless Steel MPT barb will connect any tubing with a 3/8" ID line to any fitting with a 1/2" FPT connection. Most commonly used to connect tubing to a ball valve. Great for brewers who want to upgrade the fittings in their brewery to stainless steel. A high quality fitting with no sharp burs around the edges.
Made from 304 Stainless Steel.
Use this barbed fitting with our 1/2" ID Silicone tubing for a better fit. Because Silicone tubing is soft and flexible it actually fits much better on this over sized 5/8" OD barb than on a 1/2" OD barb.
Designed and made by MoreBeer! to maximize flow this fitting is also perfect for use when a March or Chugger High-Flow pump as it allows a larger volume of wort to enter the pump, decreasing instances of cavitation.
Please note: If using 1/2" ID vinyl tubing, we recommend using hot water to heat the tubing up for easier insertion. Not recommended for use with thick wall 1/2" vinyl tubing.
For Insertion into a ball valve for connecting 1/2" ID line. Made from 304 type stainless steel.
Please note: If using 1/2" ID vinyl tubing, we recommend using hot water to heat the tubing up for easier insertion. Not recommended for use with thick wall 1/2" vinyl tubing.
Use this fitting for connecting tubing directly to your pump. 1/2" FPT on one side, with a 1/2" barb on the other. If you are not using a QD Set or a ball valve, this is a handy piece of stainless for a direct connection!
This Stainless Steel BSPP barb will connect any tubing with a 5/16" ID line to any fitting with a 1/4" Female BSPP connection.
The barb is slightly oversized at 8mm (0.315") compared to 5/16" (0.3125") which will give you a tighter connection with your tubing.
KegLand Part Number: KL06637
This Stainless Steel BSPP barb will connect any tubing with a 3/4" ID line to any fitting with a 3/4" Female BSPP connection.
The barb is slightly oversized at 20mm (0.78") compared to 3/4" (0.75") which will give you a tighter connection with your tubing.
BSP vs. BSPP
BSP (or BSPT) fittings have a tapered thread and require teflon tape to form a seal between the male and female fitting. BSP fittings are generally intended to be used with their counterpart of the same thread type. ONLY 1/2" BSP fittings are compatible with US-standard NPT fittings of the same size. BSPP fittings, on the other hand, have a straight thread, require a gasket seated inside the female fitting to form a seal, and are not compatible with NPT.
KegLand Part Number: KL06668
3/4 inch mpt and 3/4 inch barb. Made from 304 stainless. Will work on Ss Brewing technologies line of Chronical Fermenters, as well as with many 20x20 cm Plate & Frame Filters.
This Stainless Steel BSPP barb will connect any tubing with a 3/8" ID line to any fitting with a 3/8" Female BSPP connection.
The barb is slightly oversized at 10 mm (0.39") compared to 3/8" (0.37") which will give you a tighter connection with your tubing.
BSP vs. BSPP
BSP (or BSPT) fittings have a tapered thread and require teflon tape to form a seal between the male and female fitting. BSP fittings are generally intended to be used with their counterpart of the same thread type. ONLY 1/2" BSP fittings are compatible with US-standard NPT fittings of the same size. BSPP fittings, on the other hand, have a straight thread, require a gasket seated inside the female fitting to form a seal, and are not compatible with NPT.
KegLand Part Number: KL06644
If you've been looking to step up from fermenting in plastic buckets or carboys, this is an excellent choice for your next fermenter. Stainless steel is a much better option than glass or plastic, as it is extremely easy to clean and virtually lasts forever. There's also much less chance of contamination as stainless doesn't scratch like plastic. Over time, you'll get scratches in plastic fermenters from normal wear and tear, creating microscopic havens for bacteria. Meanwhile, glass carboys are always at risk of breaking which is something you will never have to worry about with stainless steel. The Bucket Buddy is a great value if you're looking for a stainless steel fermenter with built-in heating control. If you live in a cold climate, ale fermentations may be a seasonal affair, as cold ambient temperatures can easily drive down the temperature of your wort below your yeast's optimal fermentation temp range. The Bucket Buddy offers a simple solution with an integrated heating element and digital temperature control. Program your fermentation temperature and if the temp drops below your set point the unit will gently heat your wort from the bottom up via the concealed element located in the base. For cooling, you can place the fermenter in a dedicated refrigerator or drill into the lid to install a Temp Twister Cooling Coil. A temperature controller probe can then be taped to the side of the fermenter to control your cooling source, or you can drill another spot in the lid for a thermowell. Another advantage over carboys and plastic buckets is the domed base inside the fermenter which is great for yeast flocculation when fermentation is complete. The included racking arm will make it easy to transfer out every last drop of beer while leaving the yeast cake undisturbed. The entire racking arm and ball valve assembly is weldless, which means you can remove the assembly to clean and sanitize it between batches. You can even boil the assembly for added assurance that it's been sterilized. To help maintain a steady temperature and cut down on power consumption, the Bucket Buddy pairs well with either the BrewZilla Neoprene Jacket or the FermZilla Insulating Jacket. This unit comes standard with silicone tubing to transfer from the ball valve to your bottles or cans, as well as a stopper and airlock for the domed lid. Specifications: 304 stainless steel construction 9.25 gallon total capacity Digital temperature control 110V / 36W power Stainless steel outlet valve with rotating racking arm Temperature reads in °F or °C With elements turned off, hold both +/- buttons to switch between °F or °C External Dimensions: 28" H x 15" W (including handles) Internal Dimensions: 22" H x 11.75" W Please note: Heating capacity is highly dependent on ambient temperature and use of insulation. Testing has shown that the Bucket Buddy can heat to 104°F in a room temperature ambient environment without insulation. Adding insulation may increase heating capacity while colder ambient environments may lower heating capacity. KegLand Part Number: KL20695
If you've been looking to step up from fermenting in plastic buckets or carboys, this is an excellent choice for your next fermenter. Stainless steel is a much better option than glass or plastic, as it is extremely easy to clean and virtually lasts forever. There's also much less chance of contamination as stainless doesn't scratch like plastic. Over time, you'll get scratches in plastic fermenters from normal wear and tear, creating microscopic havens for bacteria. Meanwhile, glass carboys are always at risk of breaking which is something you will never have to worry about with stainless steel. The Bucket Buddy is a great value if you're looking for a stainless steel fermenter with built-in heating control. If you live in a cold climate, ale fermentations may be a seasonal affair, as cold ambient temperatures can easily drive down the temperature of your wort below your yeast's optimal fermentation temp range. The Bucket Buddy offers a simple solution with an integrated heating element and digital temperature control. Program your fermentation temperature and if the temp drops below your set point the unit will gently heat your wort from the bottom up via the concealed element located in the base. For cooling, you can place the fermenter in a dedicated refrigerator or drill into the lid to install a Temp Twister Cooling Coil. A temperature controller probe can then be taped to the side of the fermenter to control your cooling source, or you can drill another spot in the lid for a thermowell. Another advantage over carboys and plastic buckets is the domed base inside the fermenter which is great for yeast flocculation when fermentation is complete. The included racking arm will make it easy to transfer out every last drop of beer while leaving the yeast cake undisturbed. The entire racking arm and ball valve assembly is weldless, which means you can remove the assembly to clean and sanitize it between batches. You can even boil the assembly for added assurance that it's been sterilized. To help maintain a steady temperature and cut down on power consumption, the Bucket Buddy pairs well with either the BrewZilla Neoprene Jacket. This unit comes standard with silicone tubing to transfer from the ball valve to your bottles or cans, as well as a stopper and airlock for the domed lid. Specifications: 304 stainless steel construction 17.1 gallon total capacity Digital temperature control 110V / 60W power Stainless steel outlet valve with rotating racking arm Temperature reads in °F or °C With elements turned off, hold both +/- buttons to switch between °F or °C Please note: Heating capacity is highly dependent on ambient temperature and use of insulation. The 65L Bucket Buddy is appropriate for warm fermentations such as kveik. Adding insulation may increase heating capacity while colder ambient environments may lower heating capacity. KegLand Part Number: KL23061
Replacement o-ring for the ball valve included with the KegLand Bucket Buddy stainless fermenter.
Please note the color of the O-ring recently changed to white/clear. Updated images coming soon.
KegLand Part Number: KL29186
Replacement o-ring for the racking arm included with the KegLand Bucket Buddy stainless fermenter.
Single o-ring. If you are replacing both o-rings, you will need to order 2.
KegLand Part Number: KL24754
This stainless steel bulkhead is 1/2" FPT x 1/2" MPT with a flat, thick rubber washer that makes is very easy to install on most kettles. We use this bulkhead on our weldless spigot. You will need to drill a 1" hole to install the bulkhead.
This bushing from Ss Brewtech fits in with a 3/4" MPT and shrinks it to a more common 1/2" FPT. Great for your Chronical 3/4" dump valve. Made from 304 stainless steel.
This stainless steel butterfly hose clamp is perfect for use with braided/reinforced silicone tubing. The butterfly thumb screw allows for toolless tightening and untightening, so you can build out or break down your system without rummaging through the toolbox for the right screwdriver.
Fits 5/8" to 1.5" OD tubing. Actual size of the clamp is 21-38 mm (0.82" - 1.49").
KegLand Part Number: KL24440
