The humble plastic ball lock disconnect has been around a long time and is used by countless homebrewers around the world. Despite the extensive use they have seen little to no innovation for decades and KegLand wanted to change this. Enter the Duotight Ball Lock QD. The integrated Duotight design means you can connect your beer and gas line directly, easily and reliably with no need for additional fittings or clamps. It is a robust and super compact design that is incredibly easy to assemble and disassemble, making cleaning and sanitizing an absolute breeze! Made from highly chemical resistant materials with stainless springs and ball bearings (no cheap ABS plastics here) this baby is extremely resistant to commonly used chemicals such as phosphoric based sanitizers and caustics. The incredibly small form factor allows for easy stacking of kegs. The new cap design ensures a pressure seal with just hand tightening and it can be completely taken apart for cleaning with no tools required. Duotight Ball Lock QDs are offered in three sizes that correspond to the outer diameters seen on our line of EVABarrier Draft Tubing. 6.35 mm OD – features a very tight 3 mm ID that requires only 3.2 ft of length for adequate flow resistance. This is the ideal size for mobile draft or if you want to keep your kegerator as tidy as possible. 8 mm OD – the most common OD size of EVABarrier tubing. This size comes in two IDs (4 mm & 5 mm) and pairs up with the lion's share of Duotight fittings and accessories. 4 mm ID is our most recommended size for beverage lines, requiring 5-6 ft. lengths. 5 mm ID is commonly used as gas line or when 10-12 ft. beverage lines are required. 9.5 mm OD – suitable for gas lines or long draw beverage lines. At 6.3 mm ID, this size is ideal for beverage lines that will be 20 ft. or longer in length. Duotight Push-to-Connect These Duotight ball lock disconnects already have the Duotight fitting built into the ball lock disconnect. No need for additional threaded fittings. Simply push the beer/gas line in and you are done! Compact The world's most compact ball lock disconnect ever manufactured. This new compact form factor is great for tight spaces or fridges where you want to pack as many kegs in as possible. This is one of the only ball lock disconnects that allows standard ball lock kegs to be double stacked while still connected to beer and gas lines. Overmolded Poppet The overmolded poppet design means you can couple and disconnect this ball lock QD under extreme pressures of up to 150 psi (higher than most kegs working pressure) and will never have issues with the o-ring blowing out. Tool-less Disassembly Other ball lock disconnects require a tool such as a flat head screw driver or spanner to take them apart for cleaning. The new caps on these allow for easy disassembly by hand, making these easier to break down for cleaning. It's literally never been easier to remove hop particles from your ball lock disconnects. Extreme Chemical Resistance No cheap ABS plastic or nitrile seals. This ball lock disconnect is made from stainless spring and ball bearings, with an engineering polyketone resin body, EPDM and PP/EPDM overmolded poppet. This makes the quick disconnect resistant to extreme chemicals such as phosphoric and acetic acid, caustic soda, peroxide and many other acid or base chemicals which are commonly used in homebrewing. Toughness This ball lock disconnect is more robust than any other plastic ball lock disconnect ever manufactured due to the use of new engineering plastics. Don't be fooled by the small form factor — these bad boys are tough! High Flow The internal design of these allows for faster flow meaning you can slightly quicker transfers when compared to other plastic ball lock disconnects. Features: Ball Lock Quick Disconnect - Gas In Direct connect EVABarrier tubing Compact design won't interfere with keg stacking Made from highly chemical resistant materials Disassemble by hand for quick and easy cleaning Three sizes available: 6.35 mm (KL24242) 8 mm (KL20756) 9.5 mm (KL20770)
The humble plastic ball lock disconnect has been around a long time and is used by countless homebrewers around the world. Despite the extensive use they have seen little to no innovation for decades and KegLand wanted to change this. Enter the Duotight Ball Lock QD. The integrated Duotight design means you can connect your beer and gas line directly, easily and reliably with no need for additional fittings or clamps. It is a robust and super compact design that is incredibly easy to assemble and disassemble, making cleaning and sanitizing an absolute breeze! Made from highly chemical resistant materials with stainless springs and ball bearings (no cheap ABS plastics here) this baby is extremely resistant to commonly used chemicals such as phosphoric based sanitizers and caustics. The incredibly small form factor allows for easy stacking of kegs. The new cap design ensures a pressure seal with just hand tightening and it can be completely taken apart for cleaning with no tools required. Duotight Ball Lock QDs are offered in three sizes that correspond to the outer diameters seen on our line of EVABarrier Draft Tubing. 6.35 mm OD – features a very tight 3 mm ID that requires only 3.2 ft of length for adequate flow resistance. This is the ideal size for mobile draft or if you want to keep your kegerator as tidy as possible. 8 mm OD – the most common OD size of EVABarrier tubing. This size comes in two IDs (4 mm & 5 mm) and pairs up with the lion's share of Duotight fittings and accessories. 4 mm ID is our most recommended size for beverage lines, requiring 5-6 ft. lengths. 5 mm ID is commonly used as gas line or when 10-12 ft. beverage lines are required. 9.5 mm OD – suitable for gas lines or long draw beverage lines. At 6.3 mm ID, this size is ideal for beverage lines that will be 20 ft. or longer in length. Duotight Push-to-Connect These Duotight ball lock disconnects already have the Duotight fitting built into the ball lock disconnect. No need for additional threaded fittings. Simply push the beer/gas line in and you are done! Compact The world's most compact ball lock disconnect ever manufactured. This new compact form factor is great for tight spaces or fridges where you want to pack as many kegs in as possible. This is one of the only ball lock disconnects that allows standard ball lock kegs to be double stacked while still connected to beer and gas lines. Overmolded Poppet The overmolded poppet design means you can couple and disconnect this ball lock QD under extreme pressures of up to 150 psi (higher than most kegs working pressure) and will never have issues with the o-ring blowing out. Tool-less Disassembly Other ball lock disconnects require a tool such as a flat head screw driver or spanner to take them apart for cleaning. The new caps on these allow for easy disassembly by hand, making these easier to break down for cleaning. It's literally never been easier to remove hop particles from your ball lock disconnects. Extreme Chemical Resistance No cheap ABS plastic or nitrile seals. This ball lock disconnect is made from stainless spring and ball bearings, with an engineering polyketone resin body, EPDM and PP/EPDM overmolded poppet. This makes the quick disconnect resistant to extreme chemicals such as phosphoric and acetic acid, caustic soda, peroxide and many other acid or base chemicals which are commonly used in homebrewing. Toughness This ball lock disconnect is more robust than any other plastic ball lock disconnect ever manufactured due to the use of new engineering plastics. Don't be fooled by the small form factor — these bad boys are tough! High Flow The internal design of these allows for faster flow meaning you can slightly quicker transfers when compared to other plastic ball lock disconnects. Features: Ball Lock Quick Disconnect - Bev Out Direct connect EVABarrier tubing Compact design won't interfere with keg stacking Made from highly chemical resistant materials Dissamble by hand for quick and easy cleaning Three sizes available: 6.35 mm (KL24235) 8 mm (KL20749) 9.5 mm (KL20763)
PCO38 threaded tapping head pairs perfectly with Oxebar Mono PET Kegs for a lightweight, affordable draft dispensing system
Dip tube features a filter attachment to keep solids in the keg and out of your glass
Includes liquid and gas ball lock posts and pull-ring PRV rated to 36 psi
Now includes PCO38 Gen2 black elbow cap insert
This handy PCO38 Tapping Head assembly is a great way to get into kegging. Using standard homebrew ball lock disconnects, this is a convenient, light weight, robust and inexpensive solution to kegging beer, cocktails, kombucha, wine, and other beverages.
This PCO38 tapping head assembly has been designed to suit standard PCO38 bottle necks such as the 4L or 8L Oxebar Mono PET Keg. KegLand utilizes quality engineering plastics and efficient injection stretch blow mould processes to manufacture economical kegs and tapping heads for both homebrewing and commercial beers. The plastics used in the tapping head can withstand a wide range of chemicals used in the brewing industry and relatively high temperatures (212°F / 100°C).
The Ball Lock Tapping Head kit comes with 2.5 BAR (36 psi) PRV, liquid and gas ball lock posts, and dip tube with filter attachment.
KegLand Part Number: KL2714
NOTE: The Oxebar Mono Keg shown in the example photos is sold separately.
The Slimline Torpedo Keg series features a smaller diameter to maximize the space in your kegerator or keezer
Low2 lid O-ring reduces oxygen ingress by 96% compared to silicone O-rings when measured in a keg!
Brand new, all-stainless construction ball lock keg
Stackable with ball lock quick disconnects in place
Etched In and Out labels near the keg posts for easy identification
Rolled handles for a comfortable grip
Made by an ISO certified commercial keg manufacturer with high-quality laser welded seams
Torpedo Kegs too wide? Want to squeeze another keg in your kegerator? The patented design, D794,899, of the Slimline Torpedo Keg is 9% more slim than the classic model with all the same great features. Coming in at about 1/4" thinner than standard Ball Lock Cornelius Kegs, this keg has welded stainless handles and the ability to stack kegs with fittings still in place all at a great price.
Quality First
Here at MoreBeer! we love nothing more than quality interior welds. We've spent a decade rejecting kegs made overseas because the interior welds have never met our standards. If a weld is not perfect and shows evident burn marks along with nooks and crannies it cannot be sanitized effectively. Torpedo kegs are machine welded and exceed our standards for quality. This weld quality is possible because these kegs are made by an ISO certified commercial keg manufacturer.
Cool Features
Torpedo Kegs were designed to stack with Ball Lock quick disconnects in place and serving which is a cool feature for some brewers who have vertical space in their refrigerator. We also like the rolled stainless steel handles. They are comfortable to grab and will never come off like some rubber handles can over time. “In” and “Out” is etched near the keg posts for easy identification which is very handy when you are connecting lines in a refrigerator or kegerator and trying not to make a mistake.
Low2 Keg Lid O-ring
Give your beverage the absolute best protection from oxygen staling with the Low2 keg lid O-ring. Even the most perfectly sealed keg is susceptible to oxygen ingress through the hatch O-ring—yes, even if the keg is under constant pressure with CO2! Even a leak-free, pressurized keg will release CO2 molecules as they pass through the lid O-ring itself, and conversely, Oxygen molecules will permeate through the O-ring and diffuse into the keg when they reach the surface area on the other side. The level of permeability is wide ranging and highly dependent on what material the O-ring is made from. Rather than the usual EPDM or Silicone, Low2 gaskets are made from a unique composition of Synthetic M-Class and Cross-Link Elastomers. This special blend has superior oxygen barrier properties that results in your beverage staying fresher for longer.
Taking your keg on the go? Don't leave home without a custom tailored Slimline Torpedo Keg Sleeve!
Specifications:
Max Pressure: 130 psi
PRV Rating: 85 psi
High Quality Laser Welded Seams
ISO9001 Quality Assurance
Made from 304 Stainless Steel
Dimensions:
Height (in.)
Diameter (in.)
1.5 Gal
11
8 3/8
2.5 Gal
15 5/8
8 3/8
5 Gal
25 1/2
8 3/8
For a slightly shorter keg, see our Standard Torpedo Kegs!
The most affordable ball lock quick disconnect we offer!
Black color easily identifies the QD for beverage use
1/4" barb connection
This black, beverage out quick disconnect comes with a barb for attaching to a beverage line, and its high quality construction creates a sturdy seal that won’t leak gas or beer when in use.
The barb measures 1/4 inch, so 3/16 inch beverage tubing is recommend for the perfect fit.
Note: Sometiems ball lock fittings can be difficult to get fully seated on a Cornelius keg. We recommend using a quick spray of sanitizer solution to act as a lubricant and giving it a few twists while applying the ball lock.
Kegland Part Number: KL02950
Brand new, all-stainless construction ball lock keg
Low2 lid O-ring reduces oxygen ingress by 96% compared to silicone O-rings when measured in a keg!
Stackable with ball lock quick disconnects in place
Etched In and Out labels near the keg posts for easy identification
Rolled handles for a comfortable grip
Made by an ISO certified commercial keg manufacturer with high-quality laser welded seams
Set your sights on a brand new Torpedo Keg! The patented, D794,899, sleek all-stainless design represents the pinnacle of quality in ball lock homebrew kegs. With features like welded stainless handles, the ability to stack with fittings in place, amazing quality and a great price we think these kegs will become the standard by which other kegs are measured.
Quality First
The first thing we at MoreBeer! check out is interior welds. We've spent a decade rejecting kegs made overseas because the interior welds have never met our standards. If a weld is not perfect and shows evident burn marks along with nooks and crannies it cannot be sanitized effectively. These kegs are machine welded and exceed our standards for quality. The weld quality is possible because these kegs made by an ISO certified commercial keg manufacturer.
Cool Features
Torpedo Kegs were designed to stack with Ball Lock quick disconnects in place and serving which is a cool feature for some brewers who have vertical space in their refrigerator. We also like the rolled stainless steel handles. They are comfortable to grab and will never come off like some rubber handles can over time. In and Out is etched near the keg posts for easy identification which is very handy when you are connecting lines in a refrigerator or kegerator and trying not to make a mistake.
Low2 Keg Lid O-ring
Give your beverage the absolute best protection from oxygen staling with the Low2 keg lid O-ring. Even the most perfectly sealed keg is susceptible to oxygen ingress through the hatch O-ring—yes, even if the keg is under constant pressure with CO2! Even a leak-free, pressurized keg will release CO2 molecules as they pass through the lid O-ring itself, and conversely, Oxygen molecules will permeate through the O-ring and diffuse into the keg when they reach the surface area on the other side. The level of permeability is wide ranging and highly dependent on what material the O-ring is made from. Rather than the usual EPDM or Silicone, Low2 gaskets are made from a unique composition of Synthetic M-Class and Cross-Link Elastomers. This special blend has superior oxygen barrier properties that results in your beverage staying fresher for longer.
Taking your keg on the go? Don't leave home without a custom fitted Torpedo Keg Sleeve!
Specifications:
Max Pressure: 130 psi
PRV Rating: 85 psi
High Quality Laser Welded Seams
ISO9001 Quality Assurance
Made from 304 Stainless Steel
Dimensions:
Height (in.)
Diameter (in.)
1.5 Gal
10.25
9
2.5 Gal
14.75
9
5 Gal
23
9
Please Note: These are about 1/2" wider than standard Ball Lock Cornelius Kegs. Need something a bit slimmer? Check out our lineup of Slimline Torpedo Kegs!
If you want an easy way to balance your beer lines, this is the way to do it. One of the benefits of Flow Control disconnects is you don't need to rely on the small ID or line length to apply flow resistance. Rather than adjusting your line length or size, simply apply additional restriction directly on the Quick Disconnect (QD). This is perfect for people who want to serve a large range of beverages with differing carbonation levels without having to customize each line. Now with the added benefit of Duotight fittings built in.
Please be aware that even in the fully open position these FC disconnects do have some inherent flow resistance so you should use either shorter line or larger ID line that you would when compared with traditional ball lock disconnects.
Flow Control QD vs. Flow Control Faucet
One of the only drawbacks of flow control devices is that they inherently create a small amount of turbulence and therefore can cause foaming. In the past, flow control faucets have been the only common option. Flow control faucets are very popular but due to the fact that they are placed at the very end of the beer line they have no head pressure. As a result, any turbulence created can cause foaming and carbonation to come out of solution.
Flow control ball lock disconnects like these on the other hand have the ability to restrict the flow before the beer enters the beer line so the head pressure created by the beer line keeps the carbonation in solution. Even in the instance that high turbulence is created the beer will be far more resistant to foaming issues. For this reason, flow control ball lock disconnects like these have significantly better performance allowing you the flexibility to adjust line resistance easily but without the introduction of turbulence that creates foaming. It cannot fix over-carbonated beer, but it can reduce the amount of beer line you would need to pour without excessive foaming.
Duotight Ball Lock QDs
The humble plastic ball lock disconnect has been around a long time and is used by countless homebrewers around the world. Despite the extensive use they have seen little to no innovation for decades and KegLand wanted to change this. Enter the Duotight Ball Lock QD. The integrated Duotight design means you can connect your beer and gas line directly, easily and reliably with no need for additional fittings or clamps. It is a robust and super compact design that is incredibly easy to assemble and disassemble, making cleaning and sanitizing an absolute breeze!
Made from highly chemical resistant materials with stainless springs and ball bearings (no cheap ABS plastics here) this baby is extremely resistant to commonly used chemicals such as phosphoric based sanitizers and caustics. The incredibly small form factor allows for easy stacking of kegs. The new cap design ensures a pressure seal with just hand tightening and it can be completely taken apart for cleaning with no tools required.
Duotight Push-to-Connect
These Duotight ball lock disconnects already have the Duotight fitting built into the ball lock disconnect. No need for additional threaded fittings. Simply push the beer/gas line in and you are done!
Compact
The world's most compact ball lock disconnect ever manufactured. This new compact form factor is great for tight spaces or fridges where you want to pack as many kegs in as possible. This is one of the only ball lock disconnects that allows standard ball lock kegs to be double stacked while still connected to beer and gas lines.
Overmolded Poppet
The overmolded poppet design means you can couple and disconnect this ball lock QD under extreme pressures of up to 150 psi (higher than most kegs working pressure) and will never have issues with the o-ring blowing out.
Tool-less Disassembly
Other ball lock disconnects require a tool such as a flat head screw driver or spanner to take them apart for cleaning. The new caps on these allow for easy disassembly by hand, making these easier to break down for cleaning. It's literally never been easier to remove hop particles from your ball lock disconnects.
Extreme Chemical Resistance
No cheap ABS plastic or nitrile seals. This ball lock disconnect is made from stainless spring and ball bearings, with an engineering polyketone resin body, EPDM and PP/EPDM overmolded poppet. This makes the quick disconnect resistant to extreme chemicals such as phosphoric and acetic acid, caustic soda, peroxide and many other acid or base chemicals which are commonly used in homebrewing.
Toughness
This ball lock disconnect is more robust than any other plastic ball lock disconnect ever manufactured due to the use of new engineering plastics. Don't be fooled by the small form factor — these bad boys are tough!
Features:
Ball Lock Quick Disconnect - Bev Out
Adjustable flow rate
Direct connect 8 mm EVABarrier tubing
Compact design won't interfere with keg stacking
Made from highly chemical resistant materials
Dissamble by hand for quick and easy cleaning
KegLand Part Number: KL21418
The most affordable ball lock quick disconnect we offer!
White color easily identifies the QD for gas use
1/4" barb connection
This white, gas-in quick disconnect comes with a barb for attaching to a beverage line, and its high quality construction creates a sturdy seal that won’t leak gas when in use.
The barb measures 1/4 inch, so it is compatible with either 1/4 inch or 5/16 inch beverage tubing.
Note: Sometiems ball lock fittings can be difficult to get fully seated on a Cornelius keg. We recommend using a quick spray of sanitizer solution to act as a lubricant and giving it a few twists while applying the ball lock.
Kegland Part Number: KL02943
Keep your cherished Corny Kegs in perfect working order with this set of gaskets and o-rings. Having a spare set on hand is usually all you need to get your keg up and running on a moment's notice.
Kit includes two gaskets for the dip tubes, two for the body connects and one lid o-ring. Be sure to replace the gaskets on any used keg you acquire. A corny keg that has been used for soda in the past should have its gaskets replaced because the soda flavor can never be removed from the rubber.
This kit works for Ball Lock and most Pin Lock corny kegs.
New Corny Keg ready to use right out of the box New Kegs are trouble-free for years Rubber top and bottoms protect floors from dings Lid includes a tab wth hole welded in so you can hang anything from lid (dry hop our favorite) 304 Stainless Steel and great welds, this will last a tifetime Features Low2 Keg Lid O-ring which offers a 96% reduction in oxygen ingress compared to silicone Ditch the bottles and start kegging today! Save time, reduce the risk of infection and get all those bottles out of the kitchen for good! Brand new 5 gallon Kegland kegs offer convenience, security and insurance when compared to used or reconditioned kegs. There's no need to replace gaskets or other parts, no need to trust that someone else did a good job with reconditioning, and no possibility of residual flavor or aromas getting into your beer! Features: Ball lock 130 PSI Operating Pressure 5 Gallon (19 L) Capacity Dry Hop Tab Welded into Lid 304 Stainless Steel Dimensions: Height: 24.75 in. Diameter: 8.375 in. Kegland Part Number: KL0289
16g threaded CO2 cartridges that work great with the KegLand Core 360 Mini CO2 Regulator or the Duotight Mini CO2 Regulator. Comes in a package of 6 cartridges. Please note: due to air shipping restrictions, this product is only eligible for ground shipment within the contiguous United States.
Compact, all-in-one design for cost-effective, space-saving kegging.
Leak-proof Duotight fittings for fast, tool-free assembly.
EVABarrier tubing preserves flavor with superior oxidation resistance.
Portable and fridge-friendly—easily tap beverages from any cooler or refrigerator.
Discover the simplest and most cost-effective solution for kegging and dispensing your home-crafted beverages, ranging from beer and cider to cold brew coffee and draft cocktails. Designed to eliminate the need for expensive, bulky equipment, this all-in-one system provides a convenient pouring experience with a compact, space-saving footprint.
The kit utilizes advanced components, including oxidation-resistant EVABarrier tubing and tool-free Duotight fittings, ensuring your setup is leak-proof and capable of preserving superior flavor stability. Whether you are looking to tap a drink directly from your kitchen refrigerator or need a portable option for a cooler, this complete package offers the most accessible path to enjoying draft quality at home.
The 1-gallon kit option comes with two 1-gallon kegs and two tapping heads. We recommend this setup if you are using a standard kitchen fridge or want a portable system for a cooler. Since these kegs stand roughly 13" tall with the tapping head installed, they easily fit into tight spaces where height is an issue.
Complete Kit Includes:
Oxebar Keg Options: Choice 5-Gallon, 2-Gallon, or 2x 1-Gallon kegs
Duotight Mini Regulator
Duotight Handheld Beer Faucet
Duotight Push-In Fittings
Duotight Check Valve
EVABarrier Gas and Beverage Tubing
Easy Setup Instructions
Flexible CO₂ Options
Use single-use 16 g or 74 g CO₂ cartridges (not included); 74 g cartridges are recommended for best performance.
Push-Fit Convenience
Duotight fittings ensure quick, tool-free assembly with no clamps or Teflon tape required.
Incredibly Cost-Effective
The lowest-cost path into kegging and serving your own beverages, with professional-style pouring and carbonation using compact CO₂ cartridges.
Ultra-Clean, Oxidation-Free Lines
EVABarrier double-wall tubing is kink-resistant, oxygen-blocking, and PVC/BPA-free—perfectly matched to Duotight fittings.
Why Choose Flash Kegging?
Fast, clean, and compact setup.
No CO₂ tank rentals or refills—just cartridges.
Tap your drink straight from your fridge or picnic cooler.
Keg Dimensions:
1-Gallon: 12.7" H x 6.1" D
2-Gallon: 20.5" H x 6.1" D
5-Gallon: 25.1" H x 9.2" D
Quickly check your fill volume when filling kegs with cold beverage
Sticker reacts to cold temperature, turning from yellow to green
Apply two stickers on 5-gallon kegs to run the full length of the keg
These keg filler stickers are designed to help you quickly check the fill volume, especially when filling cold beverages like cold-crashed beer. When the liquid inside is cold, the color changes from yellow to green. For 5-gallon kegs, you will need to apply 2 stickers if you want the gauge to run the full length of your keg.
Size: 8.85" x 0.47"
Color Warm: Yellow
Color Cold: Green
KegLand Part Number: KL42659
These cartridges give the oomph to your mini-regulator dispensing unit! Perfect for dispensing your beer on the go. One canister will push between 1-4 Cornelius kegs, depending on how it is used and the CO2 consumption required. With the 74g adapter piece, these cartridges can be used with the KegLand Core 360 Mini Regulator or Torpedo Mini CO2 Regulator. 5/8-18 UNF threading Kegland Part Number: KL16889 Please note: due to air shipping restrictions, this product is only eligible for ground shipment within the contiguous United States.
The most affordable ball lock quick disconnect we offer!
Black color easily identifies the QD for beverage use
1/4" flare thread connection
The black, beverage-out quick disconnect with male flare fitting. Convenient to use, easy to clean.
Find out for yourself why so many brewers prefer to work with flared keg fittings. Because the fitting-tubing junction is threaded, it can be easily disconnected for cleaning without having to clip your line. Also makes swapping between ball lock and pin lock kegs in the same draft system a snap!
Kegland Part Number: KL02974
Unique Core Puncturing / Actuator results in zero gas lost from screwing in CO2 cartridges
Interchangeable ball lock disconnect orientations. 45° for plastic QDs or 90° for stainless QDs
6.5mm Duotight compatible hose barb
Swappable mini pressure gauge remains well protected within solid cast brass regulator body
Corny-style 65psi Green PRV for added safety and manual depressurizing
Switch from 16g to 74g CO2 cartridges with an adapter fitting
The new Core 360 Mini CO2 Regulator from KegLand represents a huge jump forward in the mini regulator market. After much feedback on how to make mini regulators more compact, sturdy and efficient, the brilliant engineers at KegLand have come up with this mini-beast.
The analog gauge is removable and can be swapped out with a gauge of a different pressure range or it can be swapped out for the Digital Mini Pressure Gauge.
Heavy Duty Construction
Starting with the body of the regulator, this unit is made from chrome-plated solid cast brass which means it will stand up to quite a bit of abuse. Unlike most mini regulators, the pressure gauge on the Core 360 is safely recessed in the regulator body, so if you ever drop it there is little chance that you'll damage the gauge. What's more, the gauge is removable, so you can swap it out with another mini gauge with a pressure range that better suits your application.
Unique Cartridge Connection
What really sets this unit apart from other mini regulators is the way in which you insert a CO2 cartridge. A common complaint with these types of regulators is that you can lose a lot of gas from the cartridge just from threading it into the regulator. There's that brief period where the cartridge has been punctured but you haven't fully threaded it into the regulator to form a seal. If you're not quick enough, this can result in a significant amount of lost gas. The Core 360 has a unique design feature where inserting the cartridge is a 2-step process. First you fully thread in the cartridge so it forms a seal before it's opened, and then you screw down the actuator pin to release gas into the regulator. Simple and effective.
Furthermore, the Core 360 Mini Regulator is designed to be compatible with both 16g and 74g cartridges. Out of the box it will be ready to accept 16-gram 3/8"-24 UNF threaded cartridges. But with a simple adapter you can switch to 74-gram 5/8"-18 UNF threaded cartridges.
Interchangeable Gas Outlet
Another feature we haven't seen before on a mini regulator is the interchangeable gas outlet. You can use the swivel nut connection to directly attach the regulator to a flare ball lock disconnect, or you can swap to the 6.5mm Duotight-compatible barb and connect draft tubing. This is a great option if you want to dispense a commercial keg without the need of a ball lock to sanke coupler adapter.
The regulator also has two outlet options at either a 45° or 90° angle which makes this the ideal mini regulator regardless of whether you use plastic or stainless steel ball lock disconnects.
SodaStream Compatible
If you remove the 16g cartridge bushing, you'll find TR21-4 female threads for use with SodaStream gas cylinders. These can be a great option for mobile dispensing as they provide much more gas than a CO2 cartridge and are more easily transported than a full CO2 tank.
Includes:
KegLand Core 360 Mini Regulator
6.5mm Duotight-compatible hose barb
Female Flare Fitting for MFL Disconnects
Port end cap
65psi Green PRV
SodaStream to 16g thread bushing
KegLand Part Number: KL20404
Warning: Do not overtighten onto your cylinder. It is recommended that you use a spanner to hold the neck of your SodaStream cylinder while attaching and detaching the Mini 360 Core Actuator Regulator.
Mini 360 Core Actuator Regulator | User Guide
A quick and easy draft tubing setup for dispensing your homebrew!
This Beer Line Assembly has everything you need to hook a line to your keg and pour. Great for when you're out serving brew on the go or for parties. Includes the ball lock beverage-out quick disconnect, 5 feet of 3/16" beverage tubing, a hand held faucet, and two hose clamps.
The ideal vessel for serving pre-mixed cocktails and other concoctions on draft
Easily pour in your beverage of choice through the wide corny-style lid opening without needing to remove the spear
Doubles as a line cleaning keg
Rolled handles for a comfortable grip
Low2 lid O-ring reduces oxygen ingress by 96% compared to silicone O-rings when measured in a keg!
Made by an ISO certified commercial keg manufacturer with high-quality laser welded seams
The Torpedo Cocktail Keg is the ideal vessel for serving pre-mixed cocktails and other concoctions on draft. The corny keg style lid makes it easy to pour in your beverage of choice without having to fuss with removing the spear like with standard commercial sanke kegs. Hook up a D-Style keg coupler to begin carbonating the beverage from the bottom up. These kegs provide the added advantage of fully carbonating the entire cocktail. When making drinks on the fly, carbonation is lost quickly since you're mixing carbonated and still ingredients together. But when served from a fully carbonated keg, you can enjoy the bubbles in your glass for longer!
Draft lines needing some love? The Torpedo Cocktail keg easily doubles as a line cleaning keg. Simply fill with a batch of LLC or BLC to give your bev lines a little TLC.
Low2 Keg Lid O-ring
Give your beverage the absolute best protection from oxygen staling with the Low2 keg lid O-ring. Even the most perfectly sealed keg is susceptible to oxygen ingress through the hatch O-ring—yes, even if the keg is under constant pressure with CO2! Even a leak-free, pressurized keg will release CO2 molecules as they pass through the lid O-ring itself, and conversely, Oxygen molecules will permeate through the O-ring and diffuse into the keg when they reach the surface area on the other side. The level of permeability is wide ranging and highly dependent on what material the O-ring is made from. Rather than the usual EPDM or Silicone, Low2 gaskets are made from a unique composition of Synthetic M-Class and Cross-Link Elastomers. This special blend has superior oxygen barrier properties that results in your beverage staying fresher for longer.
Specifications:
Max Pressure: 130 psi
PRV Rating: 85 psi
High Quality Laser Welded Seams
ISO9001 Quality Assurance
Made from 304 Stainless Steel
Dimensions:
Height (in.)
Diameter (in.)
1.5 Gal
10
9 3/8
2.5 Gal
13 1/4
9 3/8
We love these keg lids as either a replacement or an upgrade to the stock lid featured on many homebrew kegs. Most homebrew kegs feature a straight, parallel bale that sits extemely close to the lid when in the closed position. So close that it can be hard to get a finger or two under the bale to open it. The arms on this lid bend outward creating a nice, easy-to-grip handle to open and close the bale.
For use with Torpedo, Cornelius, and Firestone kegs. Comes with a pull-ring pressure relief valve and o-ring. PRV rated to 85 psi.
Fully carbonate your beer in under 2 days!
With the Carbonating Keg Lid you can quickly carbonate beer without the risk of over carbonating like with the burst carbonation method
Diffusion stone disperses CO2 directly into solution for faster gas absorption
Brand new keg lid complete with o-ring and PRV
The easiest way to carbonate beer. This is a Cornelius keg lid with built-in carbonation stone! Move the lid from keg to keg to carbonate as needed. Allows you to force carbonate quickly using the attached .5 micron stone with the portability of being able to move the lid from keg to keg. No more hassles of trying to attach and unattach line from the "gas in" dip tube. Simply connect your gas quick disconnect to the included fitting on the lid and allow carbonation to begin. Sometimes also called a carbonater.
We constructed the lid by welding on a 1/4" barb to the underside of the lid. To that we attached 2' of 1/4" ID tubing that attaches to a .5 micron carb stone on the other end. The flexible tubing, as opposed to rigid tubing, allows the lid inserted into any cornelius style keg. The top of the lid has a "gas in" ball lock body connect welded in place that works with the KEG710 and KEG730 gas quick disconnects.
Use:
Beer must be stored cold at 34–40°F.
Preboil the stone for 2–3 minutes before using. This assures you that your stone is sterile and any residual oils have been boiled off.
Sanitize the whole keg lid before submersing into your keg filled with beer.
Set your PSI on your regulator to 3–4psi and attach your gas in fitting to the body connect on the lid. Leave keg at this pressure for 1 hour.
Raise your pressure 2PSI per hour until you reach 10–12psi. Leave it at 10–12psi for 24 hours. Pour a pint and test the carbonation. If you think your beer needs more CO2 leave for another 4–6 hours and have another pint.
Remove carbonation lid after carbonation level is satisfactory. Return original keg lid for long term storage.
Remove the keg spear from your sanke kegs for cleaning and maintenance
For use with US-standard D-Style sanke kegs
Safe and easy hand operation
Easily and safely remove the valve and spear on American Sanke kegs with this Sanke Valve/Spear Removal Tool from MoreBeer!
This economical tool is available for a very competitive price when you order from MoreBeer!, and it is great for anyone who needs to remove their spear on a Sanke keg for cleaning or to repair damage.
Note that this tool only presses the spear down to relieve pressure on the retaining ring, you will have to remove the ring by hand.
Oversized corny keg, great for bigger batches and fermentation
Low2 lid O-ring reduces oxygen ingress by 96% compared to silicone O-rings when measured in a keg!
Brand new, all-stainless construction ball lock keg
Stackable with ball lock quick disconnects in place
Etched In and Out labels near the keg posts for easy identification
Rolled handles for a comfortable grip
Made by an ISO certified commercial keg manufacturer with high-quality laser welded seams
Set your sights on a brand new Torpedo Keg! The patented, D794,899, sleek all-stainless design represents the pinnacle of quality in ball lock homebrew kegs. With features like welded stainless handles, the ability to stack with fittings in place, amazing quality and a great price we think these kegs will become the standard by which other kegs are measured.
Quality First
The first thing we at MoreBeer! check out is interior welds. We've spent a decade rejecting kegs made overseas because the interior welds have never met our standards. If a weld is not perfect and shows evident burn marks along with nooks and crannies it cannot be sanitized effectively. These kegs are machine welded and exceed our standards for quality. The weld quality is possible because these kegs made by an ISO certified commercial keg manufacturer.
Cool Features
Torpedo Kegs were designed to stack with Ball Lock quick disconnects in place and serving which is a cool feature for some brewers who have vertical space in their refrigerator. We also like the rolled stainless steel handles. They are comfortable to grab and will never come off like some rubber handles can over time. In and Out is etched near the keg posts for easy identification which is very handy when you are connecting lines in a refrigerator or kegerator and trying not to make a mistake.
Stainless Fermenter
We've seen a lot our customers having great success using the 6-gallon Torpedo Keg as a stainless steel fermenter or "kegmenter". The extra headroom that this size offers makes it a great option for fermenting 5-gallon batches. We highly recommend using CellarScience Foam Axe if you're fermenting in the keg. Foam Axe will help reduce krausen buildup, cutting down the chance of clogging issues with the ball lock poppets and the PRV in the keg lid. It should also be noted that leaving your finished beer on the leftover trub from fermentation for too long will eventually lead to off-flavors. If it won't be consumed in 2-3 weeks, transfer your beer to a fresh keg using the Torpedo Keg Buoy which will pick up the clearest beer and leave the sediment behind.
Low2 Keg Lid O-ring
Give your beverage the absolute best protection from oxygen staling with the Low2 keg lid O-ring. Even the most perfectly sealed keg is susceptible to oxygen ingress through the hatch O-ring—yes, even if the keg is under constant pressure with CO2! Even a leak-free, pressurized keg will release CO2 molecules as they pass through the lid O-ring itself, and conversely, Oxygen molecules will permeate through the O-ring and diffuse into the keg when they reach the surface area on the other side. The level of permeability is wide ranging and highly dependent on what material the O-ring is made from. Rather than the usual EPDM or Silicone, Low2 gaskets are made from a unique composition of Synthetic M-Class and Cross-Link Elastomers. This special blend has superior oxygen barrier properties that results in your beverage staying fresher for longer.
Specifications:
Max Pressure: 130 psi
PRV Rating: 85 psi
High Quality Laser Welded Seams
ISO9001 Quality Assurance
Made from 304 Stainless Steel
Dimensions:
27.15" H x 9" D
Enjoy a never-ending supply of soda water on tap with the Continuous Soda Carbonator Keg Lid. SodaStream units are great, but filling up those tiny 1L bottles is a pain, they're expensive to swap, and they run out quickly. Hook up your mains water supply to this Carbonator Keg Lid, compatible with any standard ball lock homebrew keg, and you'll never have to think about running out of sparkling water. Setup:
Position the keg inside your fridge or kegerator (ideally below 40°F). Attach your beverage draft line to the soda water out post. Attach your gas line to the gas-in post. Set your CO2 regulator to 30-50 psi, depending on how highly carbonated you like your soda water. We highly recommend using a check valve on your CO2 line. On first use, purge the air from the headspace of the keg. Connect the mains water to the water inlet post on the lid of the keg. We recommend also using a check valve on your mains water line to prevent soda water from going back into your house mains. Depending on your mains water pressure, you may need to reduce it using the Duotight In-Line Regulator. For the Carbonator Keg Lid to work well, the mains water pressure should be 10-15 psi higher than your regulator set pressure (from Step 4). That's it. This simple unit will give you continuous soda water connected to your mains water. Please note: if you are using a CO2 regulator that uses a corny-style PRV, such as the KOMOS® regulator, you will need to swap out the standard Green PRV with the 0-100 psi Gray PRV so you can raise the pressure above 60 psi. Always check the pressure rating of your keg(s) before swapping the PRV. KegLand Part Number: KL1095
The most affordable ball lock quick disconnect we offer!
White color easily identifies the QD for gas use
1/4" flare thread connection
The gray, gas-in quick disconnect with male flare fitting. Convenient to use, easy to clean.
Find out for yourself why so many brewers prefer to work with flared keg fittings. Because the fitting-tubing junction is threaded, it can be easily disconnected for cleaning without having to clip your line. Also makes swapping between ball lock and pin lock kegs in the same draft system a snap!
Kegland Part Number: KL02967
Force carbonate and dispense from your KegLand Mini Keg
Equipped with Gas-In and Bev-Out keg posts for quick and easy attachment of ball lock disconnects
Features a flexible silicone dip tube that draws liquid from the bottom, allowing you to serve from your mini keg whether it's upright or on its side
Includes a 35 PSI pressure relief valve (PRV) for safe and controlled carbonation and dispensing
Force carbonate and serve from your KegLand Mini Keg with the Ball Lock Tapping Head. The Tapping Head features Gas-In and Bev-Out keg posts and PRV rated to 35 PSI. The flexible silicone dip tube will sink and draw liquid from the bottom of the keg, allowing you to dispense from the keg whether it's standing upright or lying on its side, whichever orientation is more convenient for your refrigerator or cooler.
The Tapping Head will add approximately 2.5" to the overall height of your Mini Keg, not including the additional height of your Bev-Out Ball Lock QD. For a more compact dispensing solution, see the Low Profile Tapping Head.
Please Note: The dip tube is designed to fit all Mini Kegs, including the largest 10L size. If using a smaller size keg, we recommend cutting the dip tube to the appropriate length so it doesn't bunch up at the bottom of the keg.
KegLand Part Number: KL06972
Heavy-duty ball lock quick disconnect made from 304 stainless steel for lifetime longevity Etched "Out" label to clearly identify the QD for gas use Pairs perfectly with stainless steel Torpedo Kegs and compatible with all ball lock corny kegs 1/4" flare thread connection Your Kegs are made out of stainless steel, why settle for plastic Quick Disconnects? Upgrade your serving setup to fully Stainless with a pair of Torpedo Ball Lock QDs! These hefty pieces are constructed of 304 SS, designed for lifetime longevity. Printed clearly with "In" and "Out" so even after a few they're easy to work with. Available for both Beer Out and Gas In, with either Barbed or Flared connections. See YMAN's below for the appropriate connectors! A flare fitting washer (KEG602) is recommended for use with this product. Perfect with our Torpedo Kegs, these will work with any Ball Lock Corny Keg. Features: 304 SS Construction - Built to last a lifetime 1/4" Flare connection Ball Lock Beverage Out 2" Height
This gas in ball lock bulkhead assembly allows you to add a ball lock post just about anywhere. Create your own pressure vessel or attach it to one of our aluminum gas manifolds for a quick connect option.
1/4" BSP threads and locking nut.
Kegland Part Number: KL03179
Heavy-duty ball lock quick disconnect made from 304 stainless steel for lifetime longevity Etched "In" label to clearly identify the QD for beverage use Pairs perfectly with stainless steel Torpedo Kegs and compatible with all ball lock corny kegs 1/4" flare thread connection Your Kegs are made out of stainless steel, why settle for plastic Quick Disconnects? Upgrade your serving setup to fully Stainless with a pair of Torpedo Ball Lock QDs! These hefty pieces are constructed of 304 SS, designed for lifetime longevity. Printed clearly with "In" and "Out" so even after a few they're easy to work with. Available for both Beer Out and Gas In, with either Barbed or Flared connections. See YMAN's below for the appropriate connectors! A flare fitting washer (KEG602) is recommended for use with this product. Perfect with our Torpedo Kegs, these will work with any Ball Lock Corny Keg. Features: 304 SS Construction - Built to last a lifetime 1/4" Flare connection Clearly Labeled Ball Lock Gas In 2" Height
The Megamouth Torpedo Keg series features an extra-large lid opening for easy cleaning
Brand new, all-stainless construction ball lock keg
Stackable with ball lock quick disconnects in place
Etched In and Out labels near the keg posts for easy identification
Rolled handles for a comfortable grip
Made by an ISO certified commercial keg manufacturer with high-quality laser welded seams
The Megamouth Torpedo Kegs are by far the easiest to clean and maintain out of any ball lock homebrew keg you'll find. With an extra-large lid opening, even the buffest of homebrewer (we hear they do exist!) will have no trouble reaching in for a good scrub when it kicks—no expensive keg washing contraptions needed! The Megamouth makes for an excellent pressurizable fermentation vessel and is the ideal choice for brewers who prefer to add dry hops and other flavoring ingredients directly to the keg.
Quality First
Here at MoreBeer! we love nothing more than quality interior welds. We've spent a decade rejecting kegs made overseas because the interior welds have never met our standards. If a weld is not perfect and shows evident burn marks along with nooks and crannies it cannot be sanitized effectively. Torpedo kegs are machine welded and exceed our standards for quality. This weld quality is possible because these kegs are made by an ISO certified commercial keg manufacturer.
Cool Features
Torpedo Kegs were designed to stack with Ball Lock quick disconnects in place and serving which is a cool feature for some brewers who have vertical space in their refrigerator. We also like the rolled stainless steel handles. They are comfortable to grab and will never come off like some rubber handles can over time. “In” and “Out” is etched near the keg posts for easy identification which is very handy when you are connecting lines in a refrigerator or kegerator and trying not to make a mistake.
Overall for the price and quality, along with free shipping from MoreBeer!, the Torpedo Keg is an amazing value!
Specifications:
Mouth Opening: 5.8" L x 4.8" W.
Max Pressure: 130 psi
PRV Rating: 85 psi
High Quality Laser Welded Seams
ISO9001 Quality Assurance
Made from 304 Stainless Steel
Dimensions:
Height (in.)
Diameter (in.)
3 Gal
13.4
11.4
5 Gal
17.9
11.4
6 Gal
20.5
11.4
10 Gal
30.3
11.4
Designed for use with the PCO38 Tapping Head. With female PCO1881 threads, it can also be used with the FermZilla Collection Container or Hop Bong Sight Glasses. The Red PRV is rated to 35 psi (2.5 BAR). Warning: Never exceed the pressure capabilities of your vessel. PRV's are not spunding valves! KegLand Part Number: KB10537
An upgraded version of our popular Gas Tubing Assembly. Our new assembly now includes 5 ft of 5/16" Ultra Barrier Gas™ PVC Free Beer Tubing, ball lock gas-in quick disconnect (barb) and two hose clamps. EJ Beverages' cutting edge Ultra Barrier Gas™ tubing has a number of advantages over regular Vinyl tubing:
Clear tubing with red stripe for identification as low pressure gas line
PVC Free and BPA Free - containes no DEHP phthalates or other plasticizers
Environmentally friendly production - does not emit dioxins
Remains flexible at lower temperatures
Temperature range of -40 to 125° F
Pressure rated up to 60 psi
Force carbonate and dispense from your KegLand Mini Keg
Low profile design minimizes overall height to help fit your keg in a cooler or compact refrigerator
Includes Gas-In and Bev-Out Ball Lock Caps for quick and easy attachment of ball lock disconnects
Dip tube filter attachment blocks sediment so you pour the clearest beer possible
Force carbonate and serve from your KegLand Mini Keg with the Low Profile Ball Lock Tapping Head. The Low Profile Tapping Head only adds approximately 1.5" to the overall height of the keg, making it the ideal dispensing solution if you need to fit your keg into a cooler or compact refrigerator. Includes PRV rated to 35 PSI and Gas-In and Bev-Out Ball Lock Caps for quick and easy attachment of ball lock disconnects. The filtered dip tube will block any sediment inside the keg so you'll be pouring the clearest beer possible.
If you'd prefer stainless steel keg posts over the plastic Ball Lock Caps, see the standard Ball Lock Tapping Head.
KegLand Part Number: KL24822
A replacement pull-ring style relief valve for your favorite keg!
This is the most common relief valve. Fits most Cornelius and Firestone style kegs, along with many others. Features a long body with spring, and gray top with pull ring.
Max. pressure rating: 100 psi
Kegland Part Number: KL03070
Connect two ball lock homebrewing kegs together via their ball lock our fittings. Handing for moving sanitizer or beer from one keg to the next. We often use this fitting when we have a big party where we dixie chain kegs together. For example if you made 10 gallons of pale ale you can use this jumper to connect the two kegs so that all 10 gallons can pour at once.
The highest quality plastic ball lock quick disconnect available to homebrewers
Built-in check valve to prevent liquid from backflowing into your draft system
Smooth operation—clicks into place on keg posts and is easily removed
Built-in flare washer—no need for a separate nylon washer that is required with stainless steel QDs
CMBecker is an international manufacturer of beverage dispensing solutions for both home and professional draft equipment
Gray plastic clearly identifies the disconnect as the gas in QD
Sleep a little easier knowing this gas in ball lock with built-in check valve has your back. The internal check valve allows gas to flow out, but won't allow backflow of liquid into your gas system. Many manifolds and regulators already feature check valves, but this disconnect will keep liquid from ever entering your gas lines in the first place. Especially handy if you force carbonate your beer using the bev out dip tube!
Why we love it: Because we've had beer shoot back into our gas line and that sucks. At some point you will have a keg that is pressurized more than the pressure in your gas system. This could be caused by different carbonation levels, a keg sitting at room temperature, etc. So for example if the pressure in your keg is at 20 psi and your regulator is set at 12 psi, when you connect your gas in quick-disconnect liquid shoots from the keg into the gas line. Eliminate that possibility with this ingenious fitting.
Features:
Internal Check Valve protects your system from liquid back flow
Made in Germany and assembled in the USA by CMB.
Extremely high quality for years of service.
NSF Approved for Food Grade Service!
These cartridges give the oomph to your mini-regulator dispensing unit! Perfect for dispensing your beer on the go. For use with the Torpedo Mini CO2 Regulator (KEG965A). One canister will push between 1-4 Cornelius kegs, depending on how it is used and the CO2 consumption required. 5/8-18 threading. Please note: due to air shipping restrictions, this product is only eligible for ground shipment within the contiguous United States.
This bev out ball lock bulkhead assembly allows you to add a ball lock post just about anywhere. Use in conjunction with the gas in bulkhead to create your own pressure vessel. The included short dip tube can be replaced with a longer dip suitable to your needs.
1/4" BSP threads and locking nut.
Kegland Part Number: KL03162
Perfect for serving your craft creations on the go or making a compact home draft system that fits inside your refrigerator
Welded from the inside out using a specialized technique for superior, more sanitary welds compared to similar mini kegs
Interlocking chimes for easy and secure stacking of multiple mini kegs
KegLand's Small Stainless Steel Mini Beer Kegs are ideal for homebrewing small batches and serving your craft creations directly from your home fridge. These compact kegs are designed for convenience and versatility.
Flexible Dispensing and Carbonation
You can naturally carbonate your beer using priming sugars or, for a more controlled approach, force carbonate and serve with the Ball Lock Tapping Head. The Tapping Head features a flexible silicone dip tube, allowing you to dispense beer whether the keg is standing upright or lying on its side. The dip tube will sink and draw liquid from the bottom, allowing you to orient the keg whichever way is more convenient in your refrigerator.
Superior Quality and Durability
KegLand's mini kegs are built to last, undergoing acid bath electrolysis to passivate the stainless steel, making them exceptionally resistant to rust. These are the only mini kegs on the market that are welded from the inside out using a specialized technique. This results in a superior, more sanitary welding finish compared to other mini kegs. When you choose a KegLand mini keg, you're investing in the highest quality available, surpassing the standards of other mini kegs of similar design.
Low2 Lid O-Ring
The sealing cap features an O-ring made of KegLand's special Low2 material which offers vastly improved oxygen barrier properties compared to silicone or EPDM, resulting in your beverage staying fresher for longer.
Expand Your Setup with Accessories
Enhance your mini keg experience with a range of available accessories, including neoprene jackets for insulation and compact tapping systems for easy dispensing.
Stackable with the 2L Mini Keg.
Specs:
4L / 1 Gal / 135 fl oz
11" High x 5.3" Diameter (280mm x 135mm)
Max Working Pressure: 45 PSI / 3 Bar
Made from 304 Stainless Steel
KegLand Part Number: KL06354
New Corny Keg ready to use right out of the box New Kegs are trouble-free for years Rubber top and bottoms protect floors from dings Lid includes a tab wth hole welded in so you can hang anything from lid (dry hop our favorite) 304 Stainless Steel and great welds, this will last a tifetime Features Low2 Keg Lid O-ring which offers a 96% reduction in oxygen ingress compared to silicone. Ditch the bottles and start kegging today! Save time, reduce the risk of infection and get all those bottles out of the kitchen for good! Brand new 2.5 gallon Kegland kegs offer convenience, security and insurance when compared to used or reconditioned kegs. There's no need to replace gaskets or other parts, no need to trust that someone else did a good job with reconditioning, and no possibility of residual flavor or aromas getting into your beer! These Premium 2.5 gal kegs have a lid with an internal tab/hook under the lid designed specifically for attaching dry hopping bags. Features: 130 PSI Operating Pressure 2.5 Gallon (9.5 L) Capacity Dry Hop Tab Welded into Lid 304 Stainless Steel Dimensions: Height: 14.5 in. Diameter: 8.375 in. Kegland Part Number: KL02882
This adapter can be installed on the Core 360 Mini Regulator from Kegland in order to use 74 gram CO2 cartridges. Use a crescent wrench to remove the stock adapter piece for 12 gram cartridges and simply screw in this adapter with 5/8-18 UNF female threading. Switching to 74 g cartridges will allow you dispense 1-4 Cornelius kegs, depending on how it is used and the CO2 consumption required. TR21-4 Male Thread x 5/8-18 UNF Female Thread Adapter only. Regulator and CO2 cartrdige sold separately. KegLand Part Number: KL2041
This portable keg faucet will surely have your friends saying "Dang, that is way classier than a picnic tap!"
This Quick Disconnect Faucet Assembly comes in handy when you take your keg with you to a gathering. Pair it with a small CO2 injector (KEG950), and you won’t have to mess with tubing when you’re away from home.
Complete assembly. Comes with QD faucet adapter, stainless faucet, faucet knob and ball lock beverage out quick disconnect.
Super-sized corny keg, great for bigger batches and fermentation
Low2 lid O-ring reduces oxygen ingress by 96% compared to silicone O-rings when measured in a keg!
Has the size and strength of a 15.5-gal commercial keg with the easy to open/clean/fill of a homebrew keg
Brand new, all-stainless construction ball lock keg
Stackable with ball lock quick disconnects in place
Etched In and Out labels near the keg posts for easy identification
Rolled handles for a comfortable grip
Made by an ISO certified commercial keg manufacturer with high-quality laser welded seams
Look out below! The Torpedo Keg Depth Charge series just dropped and they're set to send blast waves through the homebrew world. Large-scale homebrewers will appreciate the ability to fit their entire batch into a single 15-gallon ball lock keg, and you can expect the same great features that have made Torpedo Kegs such a hit. Laser welded construction for superior quality, rolled stainless steel handles that will last a lifetime, and stackable design that won't interfere with your fittings.
Quality First
The first thing we at MoreBeer! check out is interior welds. We've spent a decade rejecting kegs made overseas because the interior welds have never met our standards. If a weld is not perfect and shows evident burn marks along with nooks and crannies it cannot be sanitized effectively. These kegs are machine welded and exceed our standards for quality. The weld quality is possible because these kegs made by an ISO certified commercial keg manufacturer.
Cool Features
Torpedo Kegs were designed to stack with Ball Lock quick disconnects in place and serving, which is a cool feature for some brewers who have vertical space in their refrigerator. We also like the rolled stainless steel handles. They are comfortable to grab and will never come off like some rubber handles can over time. In and Out is etched near the keg posts for easy identification, which is very handy when you are connecting lines in a refrigerator or kegerator and trying not to make a mistake.
Low2 Keg Lid O-ring
Give your beverage the absolute best protection from oxygen staling with the Low2 keg lid O-ring. Even the most perfectly sealed keg is susceptible to oxygen ingress through the hatch O-ring—yes, even if the keg is under constant pressure with CO2! Even a leak-free, pressurized keg will release CO2 molecules as they pass through the lid O-ring itself, and conversely, Oxygen molecules will permeate through the O-ring and diffuse into the keg when they reach the surface area on the other side. The level of permeability is wide ranging and highly dependent on what material the O-ring is made from. Rather than the usual EPDM or Silicone, Low2 gaskets are made from a unique composition of Synthetic M-Class and Cross-Link Elastomers. This special blend has superior oxygen barrier properties that results in your beverage staying fresher for longer.
Specifications:
Total Capacity: 15.2 gal.
Max Pressure: 130 psi
PRV Rating: 85 psi
Height: 24.75"
Diameter: 16.05"
Made from 304 Stainless Steel
Remove a threaded keg spear from your Sanke kegs for cleaning and maintenance Compatible with D-Style and S-Style threaded spears Attaches directly to the 1/2" drive of an impact driver or pneumatic rattle gun This keg opening tool attaches directly to a 1/2" drive so it can be used with an impact driver or pneumatic rattle gun. This makes fitting and removing keg spears really fast and can save a ton of time when working with a high volume of kegs. Compatible with D-Style and S-Style kegs with threaded spears. There are two styles of Sanke kegs, those with a threaded-in spear and those that use a retaining ring, or circlip, to hold in the spear. This tool is designed for use with D- or S-Style Sanke kegs with threaded spears. For the more popular (in the USA) D-Style circlip-style Sanke kegs, use tool KEG860. Please Note: this tool does not remove the retaining ring. Once the keg has been depressurized, you will have to remove the ring by hand. KegLand Part Number: KL14908
Possibly the smallest keg you can make that will fit a corny-style keg lid. This half gallon ball lock keg works perfectly as a pressurizable growler that doesn't require any special fittings or accessories beyond the ball lock draft equipment you probably already own. If you've been considering a permanent soda water line on your draft system, this is the ideal keg to use with the KegLand Continuous Soda Carbonator Keg Lid. The low volume of this corny keg will allow the Carbonator Keg Lid to almost instantly carbonate water as it refills the keg after every pour. This little guy also works great as a line cleaning keg using a small batch of cleaning solution. 5.9" W x 9.9" H KegLand Part Number: KL20893
Due to high demand, this item is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this item to you when we receive more in mid August.
Brand-new stainless steel beer keg with US-standard MicroMatic D System Spear
Sixth Barrel Keg holds 55x 12 oz beers or 41x 16 oz pints
Compact and easy to fit multiple kegs in home kegerators or keezers
Commercial quality construction—produced and tested in an ISO 9001 Certified facility
Supply your brewery with the best kegs on the market with these 5.16 gallon 1/6 Barrel US Sanke Kegs. Our kegs are produced and tested for quality in an ISO 9001 Certified facility, abiding by strict quality control standards. Each keg is constructed entirely of Stainless Steel, ensuring a long serving life for your brewery.
The sixth barrel keg, commonly referred to as a sixtel keg, is a great option for bars and restaurants that want to offer a variety of beers but don't have the space for multiple full size kegs. They're also a great option for kegerators, as two or three sixtels will fit inside depending on the model.
Holds 55 x 12 oz beers (41 x 16 oz pints).
Features:
5.16 gal (1/6 bbl) US Sanke keg
304 Stainless Steel Construction
23" Height, 9.25" Diameter
MicroMatic D System (U.S. Sankey) Spear
Working pressure is 43.51 psi (3.0bar)
You'll love the convenience of using this complete gas tubing assembly for draft beer dispensing.
This Gas Tubing Assembly includes a ball lock gas-in quick disconnect fitting, 5 feet of 5/16" gas tubing, and two hose clamps. It's more convenient than having to hunt down all of the individual parts yourself. You'll find several places you can use this assembly in your homebrewing configuration.
Perfect for serving your craft creations on the go or making a compact home draft system that fits inside your refrigerator
Welded from the inside out using a specialized technique for superior, more sanitary welds compared to similar mini kegs
Interlocking chimes for easy and secure stacking of multiple mini kegs
KegLand's Small Stainless Steel Mini Beer Kegs are ideal for homebrewing small batches and serving your craft creations directly from your home fridge. These compact kegs are designed for convenience and versatility.
Flexible Dispensing and Carbonation
You can naturally carbonate your beer using priming sugars or, for a more controlled approach, force carbonate and serve with the Ball Lock Tapping Head. The Tapping Head features a flexible silicone dip tube, allowing you to dispense beer whether the keg is standing upright or lying on its side. The dip tube will sink and draw liquid from the bottom, allowing you to orient the keg whichever way is more convenient in your refrigerator.
Superior Quality and Durability
KegLand's mini kegs are built to last, undergoing acid bath electrolysis to passivate the stainless steel, making them exceptionally resistant to rust. These are the only mini kegs on the market that are welded from the inside out using a specialized technique. This results in a superior, more sanitary welding finish compared to other mini kegs. When you choose a KegLand mini keg, you're investing in the highest quality available, surpassing the standards of other mini kegs of similar design.
Low2 Lid O-Ring
The sealing cap features an O-ring made of KegLand's special Low2 material which offers vastly improved oxygen barrier properties compared to silicone or EPDM, resulting in your beverage staying fresher for longer.
Expand Your Setup with Accessories
Enhance your mini keg experience with a range of available accessories, including neoprene jackets for insulation and compact tapping systems for easy dispensing.
Stackable with the 5L and 10L Mini Keg.
Specs:
8L / 2.1 Gal / 270 fl oz
16" High x 6.8" Diameter (280mm x 175mm)
Max Working Pressure: 45 PSI / 3 Bar
Made from 304 Stainless Steel
KegLand Part Number: KL06378
