Beer Pump - Cold Side

If you're searching for an affordable pump to use with your temperature control system, look no further. This submersible pump can be easily integrated with an icebank or glycol chiller. Don't be fooled by its low-profile compact design. With a flow rate of 800 gallons per hour and a max lift height of nearly 10 feet, this pump will keep the solution moving in your chilling system with ease. Comes with interchangeable 1/2 in. and 3/4 in. plastic barbs.   We recommend this pump for maintaining the temperature of any batch size fermentation that is less than 10 gallons.   Maximum flow rate: 800 GPH Max lift height: 9 ft. Comes with 2 barb fittings - 1/2" & 3/4"  High quality 60W motor runs quiet Stainless steel impeller shaft 6 ft. long power cord

Read more less

Transfer beer or wine between vessels without the hassle of starting a siphon Place your receiving vessel side-by-side or even above the transferring vessel Perfect for transferring between primary and secondary fermenter, or from fermenter to bottling bucket or keg Eliminate excess oxygen exposure caused by hand-pumping or blowing into a carboy hood to start a siphon The Super Sucker transfer pump is the quickest, most hassle-free solution to moving beer or wine between vessels. Rack from primary fermenter to secondary or from carboy to keg without the excess oxygen exposure that results from hand-pumping a siphon or blowing into a carboy hood. Simply run transfer tubing from a racking cane to the pump and then to your receiving vessel, flip the switch, and let the Super Sucker do the work while you kick back and enjoy a cold beverage. With the Super Sucker you don't need gravity or CO2 pressure to move liquid around. Thanks to the pump's considerable max lift height, you can leave your heavy, full fermenter on the ground and place the receiving keg or carboy side-by-side or even above the fermenter on a countertop. The 10 mm barbed inlet and outlet are perfect for use with 3/8" ID tubing. We recommend using our Racking Cane Siphon Kit plus 5 ft. of 3/8" vinyl tubing. Secure pump connections with butterfly hose clamps for easy set up and break down. Features: Self-Priming 10 mm Barbed Inlet/Outlet On/Off Switch Max Flow: 1.12 Gal/min Suction: 5 in. Max Lift: 150 in. (12.5 ft.) Maximum Temperature: 140°F Pressure: 90 psi Voltage: 12V DC (3.5A)  

Read more less

The perfect pump for use after fermentation! Self-priming and easy to use for transfers between carboys or kegs Included pre-filter removes solids from your liquid and features a quick disconnect design to easily remove the filter for cleaning Adjustable flow rate from 0 to 3 gallons for gentle transfers and slowly pushing finished beer through plate filters Diaphragm pumps are gentle on the liquid passing through them with much less turbulence and aeration compared to magnetic drive pumps The Vintage Shop has been a pioneer in the manufacturing of products for the home wine and beer industry since 1969 Includes tubing and clamps—ready to use out of the box! Why This is a Great Pump: Self-Priming Heat Tolerant materials to 212°F when used with Silicone tubing Speed Control! Gentle Diaphragm Design Self Priming: This pump is capable of pumping gasses, meaning that pumping does not require priming! This makes transfers between carboys or kegs incredibly easy. Simply put both inlet and outlet hoses in a bucket of sanitizer and run the pump for a minute. You're then good to transfer your beer with your sanitized pump! Removable Pre-Filter: This is something which is almost always necessary on diaphragm pumps, as the diaphragm itself is very delicate, and can be ruined by small solids. The pre-filter included on this pump will work to keep solids out of the pump, extending the working life of the unit. And the filter can be removed between uses for cleaning. Heat Tolerant: All materials used in the construction of the pump tolerate temperatures up to 212°F when used with heat tolerant tubing such as silicone.  Because the pump comes with vinyl tubing you would need to replace that tubing with silicone.  Speed Control: Perhaps the most unique feature is a dial control to adjust flow from 0 to 3 gallons per minute. Use it to send your wort from the kettle to the fermenter, or even after fermentation to send beer through a plate filter (such as our FIL45). Gentle on your Beer: A diaphragm pump works by moving beer through one pulsating diaphragm into the next. It is a design that is very gentle on the liquid being pumped. When this pump was first introduced to us, we loved the idea, but had concerns that the speed control would compromise the longevity of the motor. We've built much larger pumps and normally you need a $700 frequency drive to control motor speed. However, we've been selling this pump since the mid-2000s and it continues to perform well and receive excellent customer feedback. This pump comes with 1/2" barbed ports for easy connectivity Comes with 4' tubing on both sides Heat Tolerant materials to 212°F (when used with silicone tubing) 110 Volts, 0.5 Amp, 60 Hz.

Read more less

If you're searching for an affordable pump to use with your temperature control system, look no further. This submersible pump can be easily integrated with an ice bank or glycol chiller. Don't be fooled by its low-profile compact design. With a flow rate of 1300 gallons per hour and a max lift height or nearly 10 feet, this pump will keep the solution moving in your chilling system with ease. Comes with interchangeable 1/2 in. and 3/4 in. plastic barbs.   We recommend this pump for maintaining the temperature of any batch size fermentation between 10 gallons and 2 bbl.   Maximum flow rate: 1300 GPH Max lift height: 10 ft. Comes with 2 barb fittings - 1/2" & 3/4"  High quality 100W motor runs quiet Stainless steel impeller shaft 6 ft. long power cord

Read more less

Transfer fermented, but uncarbonated, beer from carboy to carboy or from carboy to keg. For those brewers that perhaps cannot lift a carboy or have issues with siphoning this is a great solution. Self-priming (will push air) so that it can draw out of a carboy or tank. Gentle diaphragm action so as to not "beat up" the beer. Made of food-grade, NSF approved, materials polypropylene and santoprene, so no metallic interaction with the product. Pumps 3 gallons per minute. Flow can be restricted with an inline valve positioned on the outflow side. Self-regulating motor is designed to temporarily shut down, and then turn back on, when restriction pressure exceeds pump capacity. Has a heat limitation of 125 degrees Fahrenheit so cannot be used in brewing applications. Shurflo brand pump is equipped with 1/2" Male NPT posts on the inlet and outlet. Does not include the plastic barb fittings you will need to purchase separately. Please see the "You Might Also Need" section below for our recommendations regarding which fittings to attach to the pump. Technical Specifications PUMP DESIGN: Positive Displacement 3 Chamber Diaphragm Pump CHECK VALVE: (1-Way Operation) Prevents Reverse Flow CAM: 3.0 Degree MOTOR: Permanent Magnet, P/N 11-195-01, Thermally Protected VOLTAGE: 115 VAC Nominal PRESSURE SWITCH: Factory Set @ 45 PSI Shut-Off, Turn On 25 5 PSI LIQUID TEMPERATURE: 130 Degrees Fahrenheit (54 Degrees Centigrade) Max. PRIME: Self-Priming Up To 9.0 Ft. Vertical, Max. Inlet Pressure 30 PSI (2.1 Bar) PORTS: 1/2" - 14 Male Parallel Thread Materials: PLASTICS- Polypropylene VALVES- Santoprene DIAPHRAGM - Santoprene FASTENERS- Zinc Plated Steel NET WEIGHT: 5.3 Lbs (2.4 Kg) APPROVALS: UL, C-UL Listed, N.S.F. Listed

Read more less

Self-priming stainless steel impeller pump with for moving wine or beer Cast stainless pump head with 1.5" tri-clamp connections On/off switch for easy operation 11 gallons per minute reversible flow rate Made in Italy by EnoItalia Centrifugal pump with cast stainless head. 1.5" T.C. inlet and outlet.  Self-Priming. Reversible direction. Stainless impeller.  Best used for transferring wine or beer between tanks.   Specifications 11 GPM Max Pressure: 15.9 PSI (1.1 BAR) 1.5" Tri-clamp fittings Single Speed 1400RPM 194°F Max Temp Rating 14 LBS 12.6"x9.5"x7" 110V Note: Because this product is manufactured in Europe, it will come with a European plug. You will need to re-wire for use in the USA. Please see our European Equipment Wiring Colors guide for instructions on how to convert to a domestic plug.  

Read more less

Stainless steel pump with food-grade plastic impeller with for moving wine or beer 1.5" tri-clamp connections 13 gallons per minute flow rate Made in Italy by Marchisio This pump features a stainless body, housing, and bracket. It utilizes an impeller made from food-grade plastic. The impeller does not push air by itself so to prime it you unthread the priming nut on top of the filter housing and fill with water or wine. Comes with 1.5" T.C.  inlet and outlet. Has a .8 hp motor and moves 13 gallons per minute with no head. Will pump up to a height of 70'. 110v. Overall dimensions are 14.5" L x 7"W x 7"H. Weighs 15.4 lbs. Optional by-pass can be installed to restrict flow up to 25%.  This pump can handle some small solid particulate, such as grain particles, and is food grade up to 113° F. Please note the instruction manual references 230V for the voltage, but these pumps are custom configured by the manufacturer in 110V.  

Read more less

The Straight Barb Fitting is an optional replacement to the Elbow Barb Fittings that come standard on the Super Transfer Pump (H308).

Read more less