Search results for "false bottom"

Ready to upgrade your DigiBoil into a DigiMash? With the DigiMash upgrade kit you can convert the DigiBoil into a full blown electric all-in-one system. Includes false bottom, malt pipe with bottom screen, wire support, and malt pipe handle. Simply place the false bottom inside the kettle and install the malt pipe, fill with water and heat to your desired strike temperature, then add your grain and set your desired mash temperture on the digital controller. Once your mash is complete, lift up the malt pipe, drain the wort and sparge, then remove the malt pipe and proceed to boil. Includes: False bottom Malt pipe Wire support  Malt pipe handle Malt pipe bottom screen Installation & Use: Place the false bottom inside the kettle Install the wire support in the channel located at the top of the kettle Place the mesh screen inside the malt pipe and attach the handle Lower the malt pipe into the kettle so it rests on the wire support Fill with strike water and heat to desired strike temperature When desired temperature is reached, add grain and stir until well mixed When your mash is complete, use the handle to lift out malt pipe and rotate 90° so the malt pipe feet sit on the wire support Allow the wort to drain into the kettle and sparge the grain with warm water (165-175°F) When you're done collecting your wort, remove the malt pipe and proceed to boil   Please note: only the 500-watt element should be used to increase mash temperatures when the Malt Pipe is in place. Using the higher watt element(s) with the Malt Pipe inserted may cause scorching of the grain.   Kegland Part Number: KL13055

Read more less

Designed to adapt weldless punched holes into 1/2" female threaded connection ports. 1/2" Female threaded 304 Stainless steel Hi-temp silicone o-rings Fits into 13/16" punch hole

Read more less

Insulated walls to eliminate heat loss during mashing. Made from 304 stainless steel with passivated internal 2B polished finish Slotted 3-piece false bottom, adjustable height sparge arm, and large grain out manway door with removable chute Sparge arm features two inlets for HLT and recirculation 4" tri-clamp grain inlet port can be used with optional Grist Hydrator Ships domestically from within the contiguous United States MB Pro Brewing Systems are very well constructed and represent an amazing overall value. They also boast a very impressive feature set. Our Pro Insulated Mash Tun features slotted 3-piece false bottom, adjustable-height sparge arm, 4" TC port for optional grist hydrator, and a host of other key features guaranteed to satisfy the expectations of today's pro brewer. The mash tun has a slotted plate screen with a large grain out port on the side. The optional hydrator allows you to mix grain with hot liquor if you have your mill or grist case above the mash tun. There is a large top access for manual stirring. The walls of the mash tun are insulated to provide stable mashing temperatures. While intended for a single infusion mash, step mashing can be performed by recirculating through a heat exchanger. The sparge arm is adjustable in height and it is intended to have an inch of water above the grain and have the bottom of the diverted plate resting on top of the grain for low oxygen pickup during recirculating and sparging. We recommend that you use a grant to avoid creating suction on the bottom of the mash screen. It is possible to pull 23,000 lbs of force on the screen with a pump and a fully stuck mash and even partial vacuums can produce significant force. Alternatively, you can install a vacuum breaker ahead of the pump. Replacement screens are available for special order. We strongly recommend using a Wort Grant when pumping off the mash tun to avoid the possibility of collapsing the screens. Great Quality from MB Our brewing systems are made at a family owned manufacturer in the Ningbo region of China. Ningbo is where most premium beer tanks and brewing vessels come from and represents a known style and level of quality when compared to other areas of China. Our professional brewhouse equipment is designed by our in-house R&D designer Colin Kaminski, a former brewmaster for 15 years. Cleanability, ease of use, and durability are our primary design criteria. Our manufacturing partner in China is a father/son team that takes great pride in what they do. Some discount dealers buy from different manufacturers who offer one-off deals. That can be fine one time but not the next. Great Value from MoreBeer! Pro If you used MoreBeer! as a homebrewer, you may not know that MoreBeer! & MoreBeer! Pro combined is one of the largest brewing supply companies in the world with over 250,000 customers. We’ve seen countless homebrewers turn pro, and there’s nothing that makes us happier than being a part of that transition. As a privately owned brewing supply company that's been in business for over 25 years, we’ve established relationships with suppliers and manufacturers around the world and at every level of the industry. We get a great price and we pass that on to you. All Features: Insulated for low heat loss Slotted 3 pieces false bottom Large side grain out door Removable grain out chute 4" TC grain inlet port for optional grist hydrator Adjustable Height Sparge Arm for better HSA performance Sparge Arm has two inlets, HLT and Recirculation. Large top lid for easy stirring PT10 Probe Analog Temp Gauge Internal LED Light Specifications for 3.5 bbl Mash Tun: Grade 304 Stainless Steel Internal Finish: #2B Tank Height: 56" Height w/ Hydrator: 72" Tank Diameter: 41" Empty Weight: 360 lbs Working Volume: 3.5 bbl Max Volume: 4.6 bbl Manway: 20.8" x 16.9" All ports are 1.5" TC except for 4" TC Sparge Arm Port, 4" TC Grist Hydrator Port, DN80 LED Light Port Please Contact our Customer Service department at 1-800-600-0033 to assess shipment costs and place an order.

Read more less

Due to high demand, this item is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this to you when we receive more inventory. MB Pro Brewing Systems are very well constructed and represent an amazing overall value. They also boast a very impressive feature set. Our Pro Insulated Mash Tun features slotted 3-piece false bottom, adjustable-height sparge arm, 4" TC port for optional grist hydrator, and a host of other key features guaranteed to satisfy the expectations of today's pro brewer. The mash tun has a slotted plate screen with a large grain out port on the side. The optional hydrator allows you to mix grain with hot liquor if you have your mill or grist case above the mash tun. There is a large top access for manual stirring. The walls of the mash tun are insulated to provide stable mashing temperatures. While intended for a single infusion mash, step mashing can be performed by recirculating through a heat exchanger. The sparge arm is adjustable in height and it is intended to have an inch of water above the grain and have the bottom of the diverted plate resting on top of the grain for low oxygen pickup during recirculating and sparging. We recommend that you use a grant to avoid creating suction on the bottom of the mash screen. It is possible to pull 23,000 lbs of force on the screen with a pump and a fully stuck mash and even partial vacuums can produce significant force. Alternatively, you can install a vacuum breaker ahead of the pump. Replacement screens are available for special order. We strongly recommend using a Wort Grant when pumping off the mash tun to avoid the possibility of collapsing the screens. Great Quality from MB Our brewing systems are made at a family owned manufacturer in the Ningbo region of China. Ningbo is where most premium beer tanks and brewing vessels come from and represents a known style and level of quality when compared to other areas of China. Our professional brewhouse equipment is designed by our in-house R&D designer Colin Kaminski, a former brewmaster for 15 years. Cleanability, ease of use, and durability are our primary design criteria. Our manufacturing partner in China is a father/son team that takes great pride in what they do. Some discount dealers buy from different manufacturers who offer one-off deals. That can be fine one time but not the next. Great Value from MoreBeer! Pro If you used MoreBeer! as a homebrewer, you may not know that MoreBeer! & MoreBeer! Pro combined is one of the largest brewing supply companies in the world with over 250,000 customers. We’ve seen countless homebrewers turn pro, and there’s nothing that makes us happier than being a part of that transition. As a privately owned brewing supply company that's been in business for over 25 years, we’ve established relationships with suppliers and manufacturers around the world and at every level of the industry. We get a great price and we pass that on to you. All Features: Insulated for low heat loss Slotted 3 pieces false bottom Large side grain out door Removable grain out chute 4" TC grain inlet port for optional grist hydrator Adjustable Height Sparge Arm for better HSA performance Sparge Arm has two inlets, HLT and Recirculation. Large top lid for easy stirring PT10 Probe Analog Temp Gauge Internal LED Light Specifications for 3.5 bbl Mash Tun: Grade 304 Stainless Steel Internal Finish: #2B Tank Height: 56" Height w/ Hydrator: 72" Tank Diameter: 41" Empty Weight: 360 lbs Working Volume: 3.5 bbl Max Volume: 4.6 bbl Manway: 20.8" x 16.9" All ports are 1.5" TC except for 4" TC Sparge Arm Port, 4" TC Grist Hydrator Port, DN80 LED Light Port Please note: the primary image shows the mash tun with optional grist hydrator (sold separately). Please Contact our Customer Service department at 1-800-600-0033 to assess shipment costs and place an order.

Read more less

Pro-Grade Construction: Made from high-quality 304 stainless steel with a welded dish bottom for complete drainage and easy cleaning. Enhanced Cooling & Clarity: Includes an innovative jacketing system for efficient cooling and a welded tangential arm for enhanced whirlpooling, ensuring clear wort transfers and maximum hop utilization. Sanitary Connections: Features sanitary welded TC ferrules for leak-free, professional-grade connections. Enhanced Usability: Includes silicone-gripped handles, a TC-ported lid for CIP, and raised legs for convenient access. Fully Customizable: The kettle arrives without fittings or valves, giving you a blank canvas to customize with your preferred accessories. Elevate your homebrewing craft with the BrewBuilt Dish Bottom Kettle, now enhanced with a tangential whirlpool arm and an integrated cooling jacket. This professional-grade kettle is meticulously crafted from high-quality 304 stainless steel, ensuring durability and a lifetime of flawless brews. Experience the revolutionary welded dish bottom, engineered for unparalleled complete drainage, ensuring every precious drop of wort is utilized and cleanup becomes a breeze. The integrated tangential whirlpool arm allows for efficient hop and trub separation, creating a compact cone at the bottom of your kettle, leading to clearer wort and better fermentation. The built-in cooling jacket provides rapid and controlled chilling of your wort, eliminating the need for external immersion chillers and streamlining your brew day. High-quality sanitary welded TC Ferrules provide a lifetime of leak-free use and make sanitary connections effortless, a standard in professional breweries now accessible for homebrewing. Comfort and safety are prioritized with silicone-gripped handles to protect your hands from heat. The lid comes welded with a TC port, ready for CIP (Clean-in-Place) and other future accessories. For convenient access to lower ports, the kettle is raised on sturdy legs. BrewBuilt Kettles are the same high-performance kettles used in our Next Generation BrewSculptures, guaranteeing professional-grade results. Available in a wide range of popular homebrew sizes—10, 15, 20, 30, and 50 gallons—they cater to every brewing scale. Build Your Own Brewing System: This BrewBuilt Kettle provides the perfect foundation for your custom brewing setup, whether you're building a dedicated Hot Liquor Tank (HLT), Mash Tun, or Boil Kettle. It does not include all accessories, giving you the freedom to purchase the specific hardware you need to complete your ultimate brewing system. Major Features for Brewers: High-Quality 304 stainless steel construction Welded Dish Bottom for complete drainage - easy cleaning, no loss Integrated Tangential Whirlpool Arm for efficient hop and trub separation Built-in Cooling Jacket for rapid and controlled wort chilling High-Quality sanitary welded TC Ferrules Handles with Silicone grips to avoid burning hands Lid comes welded with TC port for CIP and other accessories down the road Kettles are raised on legs for easy access to lower ports Same Kettles used in our Next Generation BrewSculptures Wide Range of homebrew sizes - 10, 15, 20, 30, 50 gal Please Note: This kettle is designed for customization. While it includes the tangential whirlpool arm and cooling jacket, other necessary hardware—including heating elements, valves, thermowells, and clamps—must be purchased separately to build your desired brewing system.

Read more less

Effortless Grain Removal: Simply attach the stainless steel chute to the integrated grain door on your BrewBuilt Dish Bottom Mash Tun for a clean and controlled way to empty spent grains directly into a bucket. Mess-Free Brewing: This essential upgrade eliminates spills and reduces cleanup time, ensuring a quicker and more efficient post-brew day process. Durable and Sanitary Design: Constructed from durable, food-grade stainless steel, the grain chute is built to last and is easy to clean, maintaining a sanitary environment for your brewing process. Tired of messy grain removal? The BrewBuilt Grain Chute is the essential upgrade for your BrewBuilt Dish Bottom Mash Tun. Designed to fit the integrated grain door, this chute provides a clean and controlled way to remove spent grains. Simply attach the stainless steel chute to the grain door and use a rake or paddle to push the grain directly into a bucket or disposal bag. This simple addition eliminates spills on the floor, reduces cleanup time, and makes grain removal quick and efficient. Crafted from durable, food-grade stainless steel, the BrewBuilt Grain Chute is built to last and easy to clean. Get yours and make your next brew day a little less messy.

Read more less

Kettle Maximizer allows you to pull liquor or wort from below the depth of your kettle's bottom port Angle straight down in hot liquor tanks to maximize pick up Rotate to your preferred pick-up height in boil kettles to leave trub behind when transferring to fermenter The tri-clamp maximizer is recommended for boil kettles and hot liquor tanks with 1.5" T.C. bottom ports. This fitting will allow you to pull liquor or wort from below the depth of your kettle's bottom port without the need to tip your vessel. For hot liquor tanks, point the end of the tube straight down to maximize pick up. For boil kettles, you can rotate the maximizer to position the end of the tube at your preferred height above the bottom of the kettle, leaving room for a layer of trub that will be left behind in the kettle when you transfer wort to your fermenter. 1.5" tri-clamp Tube Length: 6.5" Overall Length: 8.18" Made from stainless steel

Read more less

No Need to Upgrade Later, The X3 Comes Fully Loaded: Built-in external cooling jacket with 1.5" TC Ports Neoprene jacket for insulation Pressure Pack lid with floating dip tube, draft style QD connections for sampling/serving, and an extra 1.5" TC for hop bongs. The Clear Flex Chamber Bottom Dump allows you to see fermentation, collect and remove trub, and has added ports for purging, oxygenating, carbing and more... so flexible. Highest quality mirror polish finish inside and out Welded, ground and polished interior welds are the very highest quality and the ultimate for sanitation New Features: Professional 8” Tri-Clamp lid replaces the need for a complicated band clamp to attach the lid Four crossbar reinforced legs, that flare out, create the most stable base and more access to the front fittings and dump system Horizontal ports on the cone, just like pro tanks, allowing your racking arm, carbstone, and thermometer to have a horizontal placement in your tank. This allows for smaller minimum batch sizes, better carbonation, and more 3" oversized bottom port and Butterfly Valve with 3” tri-clamp Flex Chamber collection vessel The new X3 from BrewBuilt sets the new standard for quality. We guarantee that you will love the fit and finish of the X3 Uni Jacketed Conical. Made entirely of 304 stainless steel, with flawless welds and a dazzling mirror-polish finish inside and out that is simply the best. The BrewBuilt X3 Uni is easy to sanitize and even easier on the eyes. It is definitely Instagram worthy! #BrewBuilt External Cooling Jacket When it comes to temperature control for a homebrew conical fermenter the holy grail has been an external cooling jacket. Internal cooling coils have long been the answer and while they are simpler to make and relatively inexpensive, they are harder to clean and have issues cold crashing in warm environments. The BrewBuilt X3 Jacketed Conical offers maximum cooling power without any compromise of sanitation. 8” Tri-Clamp Top Port New to the X3, the 8” Tri-Clamp lid is rock solid and easy to use. The 8” opening allows plenty of space to still get in and clean the inside of the conical by hand if desired. A unique 8”, three-piece, tri-clamp is used to make sealing the top very easy and very secure. Extra Large 3” T.C. Dump Valve The largest in the industry. Dry hop to your heart's desire. Try as they might, hopheads will have a hard time clogging this conical. With an oversized 3" bottom port, you’ll have all the clearance you need (and even more than some pro brewers) to drop out your dry hop additions with ease. The slick mirror-polish finish on the inside allows flocculating yeast to collect neatly at the bottom of the cone as they slide right down the smooth interior walls. The butterfly dump valve integrates perfectly with the optional Flex Chamber Collection Jar and Yeast Harvester. Reinforced Four-Leg Foundation There’s a common complaint about the tippiness of three-legged units. Three legs may be fine when the fermenter is sitting still on an even surface, but users are often forced to purchase a bracing shelf for more stability if they add casters or leg extensions. A conical is only as worthy as its foundation, so BrewBuilt modeled the X3 after professional-level brewery tanks with a four-leg, reinforced base. This seemingly small design feature is more expensive to produce, but it's what makes the X3 conical exceedingly stable when compared to other models. When you fill up your fermenter with delicious fresh wort, you want to trust the vessel that’s holding your latest creation. Brewers shouted from the mountaintops that they wanted stronger, sturdier legs right out of the box that doesn’t require an additional bracing shelf. The four-leg, welded-bar reinforced system is absolutely rock solid. This is an especially critical feature if you plan to add rolling casters so you can easily glide the fermenter around your brewery. The reinforced four-leg design not only increased the stability and strength of the conical but also allows the unit to stand taller, thereby eliminating the need for extensions in almost every situation. An elbow, a sight glass, or the Flex Chamber can be mounted under the unit with room to spare. Adjustable Feet The X3 Jacketed Conical comes standard with reinforced thread-in adjustable feet. If your home brewery has uneven flooring, you can quickly and easily level out the fermenter. The feet can be swapped out with high-quality casters at any time. Flex Chamber Collection Jar - Trub Separator & Yeast Harvester Working in collaboration with KegLand, we developed the pressurizable Flex Chamber Collection Jar. It attaches directly to the butterfly dump valve and can be used for removing trub, harvesting yeast, and many other tasks. Since it's made from crystal clear Triton, you'll be able to visually monitor fermentation activity just as you would with a sight glass. Ball lock adapters can be attached to the threaded ports on either side, allowing you to connect oxygenation or carbonation stones, or flush the Flex Chamber with CO2 and use it to inject hops or other ingredients into your conical. Also, a great option for storing yeast! Simply attach a 3" T.C. end cap or PRV and store your harvested yeast in the fridge for your next fermentation. Pressure Pack with Clear Float Technology Adding pressure capability will allow you to ferment, carbonate, and even serve all in one vessel. The Pressure Pack features the unique Clear Float Technology racking tube that can be used for taking samples, transferring to keg, or serving finished beer. This innovative feature draws beer from the top down, which means you’re always pulling the clearest, most sediment-free beer possible. Using pressure to draw a sample from the floating dip tube will also eliminate the tiny bit of oxygen that would be injected into your beer every time the traditional sample valve is opened. Pressure transferring from fermenter to keg is the best way to protect your beer from oxygen when it’s at its most vulnerable state. Kegging could be considered the final hurdle in the brewing process, where limiting oxygen exposure is critical. This could mean the difference between your beer tasting great for months or tasting great for a week. Don’t take any chances. Use the Pressure Pack to keg from the top down and leave sediment behind. Other Features You’ll Love: Downward-facing Blowoff U Barb prevents blow off tubing from kinking and is much easier to remove and clean than a fixed stainless blow off Stainless steel lid clamp with single-piece molded silicone gasket In our GEN 3 redesign, we've added two more 1.5" T.C. ports to the cone and body for additional flexibility with current and upcoming product add-ons X3 Accessories: BrewBuilt Kit for Fermenting Under Pressure (Required to ferment or seal/cap an X3 with an active fermentation) The Pressure Relief Valve (PRV) that comes with the conical is not sufficient for fermentation as it can become clogged with Krausen. To ferment or seal/cap an active fermentation requires the use and safety of the Pressure Fermentation Kit. This no-compromises kit includes the same hardware you will find on a commercial unitank, including a dedicated pro level spunding valve, a sealed pressure gauge, and a dedicated commercial PRV. Read more about these key hardware features in the kit copy. Also included is liquid Foam-Axe which helps reduce Krausen. Please read and follow all special instructions that come with the kit as well as your instruction manual. Hop Bong Oxygen-Free Dry Hopping Device The Hop Bong is a versatile pressurizable tri-clamp accessory that is perfect for purging oxygen from your dry hops before dropping them into your fermenter. Load up the Hop Bong, flush it with CO2, purge out oxygen with the handy PRV on top, then simply open the Butterfly Valve to inject your beer with a 6 oz payload of dry hops. High Roller Caster Set Go mobile with this heavy-duty caster set. Your fermenter moves around the brewery a lot, so why not give it some glide? Roll from sanitizing to kettle transfer to keg transfer to cleaning with minimal effort. Moving a stainless conical around can be taxing. Give your back a break and upgrade your conical with a set of rolling casters. IceMaster Max 2 Built to pair perfectly with the IceMaster Max 2 glycol chiller. Easily and efficiently control your fermentation temperature and cold crash for conditioning and clarifying. Pair with our BrewBuilt Insulated Tubing Kit that comes complete with premium quick disconnects with shutoff valves that provide a “dry break” when they’re disconnected. Immersion Heater The X3's cone features a 2" tri-clamp port specifically for installing an Immersion Heater. The low watt density heating element gently warms your fermenting beer without scorching. A must-have for brewers living in colder climates or if you want the peace of mind that your temperature will never drop too low for your ale or kveik strains regardless of the time of year. Full List of X3 Conical Features: External Cooling Jacket with 1.5" Tri-Clamp connections Pressure Pack with Clear Float, a floating dip tube that draws beer from the top down. Flex Chamber Collection Jar, a clear, pressure capable bottom jar that allows you to see fermentation, remove trub, and connect additional accessories Neoprene insulation sleeve Wide base with 4 legs for stability 304 stainless steel construction Mirror polish finish Interior welds are the best in the business - uniquely ground and polished (1) 2“ TC port for direct immersion heaters (3) Horizontal welded cone ports (1) 8" Lid Cap Opening with 8” TC Clamp (5) 1.5" TC Lid Openings 3" TC bottom dump with 3" TC butterfly valve 1.5" Thermowell for inserting thermal probe (4) Adjustable feet Silicone tube for blow off Stainless 8” Three Piece Tri Clamp & one piece molded gasket Built-in 15 psi PRV (Not sufficient for fermentation - optional Pressure Fermentation Kit required for pressure fermentations) For volume and dimensional specs, Download the PDF. Installation Note: The Pressure Pack's Clear Float floating dip tube is sized to fit all models of the BrewBuilt Conical. Depending on the size of your fermenter, you may need to shorten the silicone tube for better performance. When installed on your empty fermenter, you ideally want the dip tube to hang freely with just enough length for the end of the dip tube to touch the bottom of the tank.

Read more less

All the crucial features of a top-shelf brew kettle at an incredible price! Perfectly sized for 10 gallon batch brewers Made from stainless steel throughout which is easy-to-clean and offers a lifetime of reliable use Two welded 1/2" ports for common threaded brewing accessories—ball valve and barb fitting are included for the bottom port Internal volume markers make it easy to measure pre boil volume and post boil volume Silicone grips made for comfortable, slip-free handling If you’re searching for a fully featured brew kettle but don't want to break the bank, the Brewmaster 14 Gallon Stainless Brew Kettle will certainly do the trick. Made of 100 percent stainless steel and available for a truly amazing price, this reliable brew kettle is perfect for first-time brewers and experienced home brewers alike. Two ½-inch couplers are welded to the side of the kettle, and the bottom coupler can even be threaded on the inside of the kettle to use with a diverter or a kettle tube screen. These kettles are upgraded with Silicone Grip Handles and Stamped volume markers on the inside, making brew day that much easier. Includes a ball valve and a threaded adaptor to 3/8" barb for easily attaching transfer tubing. Also included is a threaded 1/2" plug for the thermometer port. Thermometer is not included and can be added at any time. Features: 14 Gallon Stainless Steel Brewmaster Brewing Kettle Two Welded 1/2" Full Couplers allow for internal and external attachments Stainless 1/2" Full Port Ball Valve & nipple included for bottom Coupler Stainless 1/2" Plug included for top coupler Stamped Volume Markers Silicone Handle Grips Internal Threading allows for conversion to Mash Tun or addition of whole hop filters 1.2 mm thick walls Made from 201 Stainless Steel Approximate Dimensions 17.5" tall 16" wide, 1.2mm thick This item does not work with induction burners A ball valve, nipple, and plug are included for the welded couplers. A thermometer, false bottom, or kettle screen can be added separately

Read more less

The Ultimate BrewZilla Combo Pack! Get the Gen 4 BrewZilla & our most highly recommended accessories at an unbeatable price! Includes all of our favorite accessories for the BrewZilla including the Neoprene Jacket to speed up heating times, Hop Spider to keep vegetal matter out of your wort, and Chilling Connection Kit so you're ready to use the Immersion Chiller out of the box We think all BrewZilla brewers will eventually upgrade their systems with these accessories, so buy them together and reap the savings! Also available in 220V (AG583) Combo Pack Includes: BrewZilla Brewing System | Gen 4 | 9.25G | 110V Neoprene Jacket Hop Spider Wort Chiller Connection Kit Gen 4 BrewZilla All-in-One Brewing System WiFi / Bluetooth enabled RAPT Controller tracks your brewday and automatically uploads detailed information to the RAPT portal The top mounted RAPT Controller can be tilted upward for easy viewing, or detached from the unit to mount it on the wall or placed on your bench Mirror polished dome shaped bottom with center drain — get every last bit of wort into your fermenter while the perforated bottom screen filters out 95% of hot break and hop matter Make larger batches or higher gravity beers! BrewZilla offers the largest malt pipe capacity for units in its size range, and the Gen 4 unit has a 30% larger malt pipe compared to the previous generation Perforated bottom on the newly designed malt pipe allows for improved mash recirculation flow without sacrificing efficiency Element power percentage can be adjusted via the RAPT Controller. Go full power to heat up quickly, or dial it down so you don’t overshoot your strike water temp The built-in pump is plumbed to both the recirculation and arm and the bottom ball valve. Recirculate wort during your mash, then close the recirculation valve and pump wort to your fermenter via the bottom valve Pair with the RAPT-enabled Bluetooth Thermometer, allowing your BrewZilla to calculate a core mash temperature reading and more accurately control temperatures and mash steps More RAPT-enabled accessories are coming, and future firmware updates can be downloaded to the RAPT Controller itself over the internet WiFi/Bluetooth Enabled RAPT Controller The RAPT Controller is mounted to the top of the boiler body, allowing for easy operation when you have the unit set on the ground. The controller can be tilted upwards to give you an even better view, or it can be removed from the BrewZilla entirely if you’d prefer to mount the controller on your wall or lay it down on a workbench. From the controller, you’ll orchestrate your entire brew day. Program mash steps, dial in element power, and operate the integrated pump all from one screen. But the RAPT Controller is much more than a beautiful, full-color display switch board. Once synced to the RAPT Portal, you’ll be able to track, record and monitor your brews online. No need for handwriting notes or punching brew day details into your phone – all of the data from your brew is automatically logged to your portal profile. This information doesn’t just include your mash profile; it also captures detailed information about your element power and pump activity, opening the door for very precise repeatability. And the RAPT Portal isn’t just a digital archive for your brew days. With your BrewZilla powered on, you can control your brewery from virtually anywhere using your phone’s web browser. Not sure when you’ll be home from work or your kid’s ball game going into extra innings? No problem! Before you head out, simply log into the RAPT Portal from your phone and tell the BrewZilla to start heating your strike water. Along with remote control, the portal enables you to program alarms and push notifications for all of your boil additions. We’ve all been caught up with a side task and failed to throw in that yeast nutrient or clarifying agent at the end of the boil, but the BrewZilla has the back of even the most forgetful brewer! But wait, there’s more! In addition to WiFi connectivity, the RAPT Controller is also a Bluetooth gateway device. KegLand is currently developing various Bluetooth devices such as the Bluetooth Beacon Thermometer and other sensors which will be compatible with your brewery upon release. The RAPT Controller is able to receive information from Bluetooth Low Energy (BLE) devices, adjusting its processes based on this new stream of information while simultaneously logging it to your RAPT Portal. With the Bluetooth Beacon Thermometer, for example, you’ll be able to feed temperature readings from the top of your mash bed to the controller. The controller will then compare this reading with the main temp probe reading at the base of the kettle and adjust element cycling based on these combined readings. Finally, the RAPT Controller WiFi connectivity allows you to update the controller’s firmware with a single click. Take advantage of new features and accessories as soon as they become available by simply keeping your BrewZilla connected to your local WiFi network. And again, the WiFi is already built-in! No need to come back for an expensive add-on accessory down the road. High Capacity Malt Pipe With an approximately 23.5 lb capacity, the BrewZilla can mash nearly 50% more grain than similar sized models of the Anvil Foundry and Grainfather G30. If you want to fill your fermenter with more than a 5-gallon batch worth of wort, or brew the highest gravity beer recipes, the BrewZilla is the brewhouse for the job. And the included malt pipe is just the beginning. If you want to expand your brewery’s grain capacity even further, KegLand makes Boiler Extension Kits and Extended Malt Pipes for that very purpose. The malt pipe features a perforated section at the bottom which improves mash recirculation flow without sacrificing efficiency. Concave Base with Center Draining Leave no wort behind! The concave base with center drain means you’ll be able to extract every last drop of wort to your fermenter. If you’ve brewed in a traditional flat bottom kettle, this center drain may be a bit perplexing at first. Many brewers are used to whirlpooling after the boil to pull hop matter into the center of the kettle, then transfer out using a pick-up tube that pulls from the kettle wall in order to avoid sucking up the solids. But fear not! One of the key features of the BrewZilla is the false bottom protection screen. This screen avoids the need for doing a whirlpool, filtering wort as it transfers and blocking more than 95% of hops and hot break from getting sucked into the pump. This not only prevents blocked pump issues, it also increases the efficiency of your brewhouse by eliminating kettle loss from wort that may have otherwise been left behind. Ultra Low Watt Density Elements The concave base on the BrewZilla also allowed for larger heating elements with significantly lower watt density than other breweries. When a lot of energy is coming off of a small element, the local temperature near the element can be so high that it scorches the wort and causes caramelization. Lower watt density essentially means you can produce lighter color beers that would otherwise have fallen victim to caramelization effect. It also reduces that chance of boilovers and reduces stress on the elements which extends their life expectancy. Easy Access Built-In Pump The built-in pump allows you to recirculate your wort during the mash for improved efficiency and more even temperature distribution. But it can also be used to transfer your wort from kettle to fermenter rather than relying on a gravity feed, and with the optional CIP Rotar, you can used the pump to clean your BrewZilla (or fermenter) after every use. During your brew day you’ll be able to control the pump from the RAPT Controller with a dedicated button for turning the pump on and off. Another feature you’ll find on the controller is adjusting the pump flow. This doesn’t control the actual volume of the flow (you can do that from the ball valve located on the recirculation arm), but rather cycles the pump on and off automatically based on your setting. At 100%, the pump remains on continuously. But at 80%, the pump will cycle to be on 80% of the time and off 20% of the time. This may not be a feature that every brewer thinks they need, but it’s an excellent way to avoid running the pump dry accidentally, as the time the pump is off allows recirculating wort to filter through the grain bed and back into the pump inlet. If you flip over the boiler, you’ll find the magnetic drive pump and all the plumbing is right at your fingertips. This means you don’t have to disassemble the base in order to access the pump for cleaning or maintenance if required. It also means the plumbing can be changed more easily too. For instance, the unit comes as standard with the plumbing from the pump feeding both the recirculation arm and the transfer valve, but you change this so the tap outlet bypasses the pump if you prefer. MoreBeer!'s Final Word We’ve been selling all-in-one brewing systems ever since they first hit the market, and we have to say that the Gen 4 BrewZilla is not only the most feature-packed unit ever made, it’s also offered at an incredibly competitive price point when compared to other systems. You’ll get all of the cutting edge Bluetooth technology you’d get with the Grainfather and at an exceptionally lower price tag. Plus, you get the WiFi capabilities as standard, rather than as a $100 add-on accessory. When it comes to mash recirculation, that’s yet another built-in feature on the BrewZilla, and the pump can also be used for transferring and CIP cleaning. The Foundry has a great starting price, but if you want to unlock its full potential, you’ll need to spend another $100 for the recirculation pump kit. What’s more, no other system in the same ‘weight class’ has the same grain capacity. And if the standard capacity isn’t quite enough, the BrewZilla can be easily upgraded with a Boiler Body Extension Kit and Extended Malt Pipe. When you purchase the BrewZilla, you can feel confident that you’re investing in a top shelf system and all of the critical features you’re expecting will be included. Perfect for Distillation If you want to expand your lineup of homemade libations to offer Spirits in addition to Ales & Lagers, the BrewZilla makes an excellent pot still! Add the Distillation Lid upgrade and pair it with an AlcoEngine Copper Reflux Condenser or Copper Pot Still Top. AlcoEngine Stills have been selling on the home market for years and offer some of the most affordable, beginner-friendly stills you'll find. Features: Gen 4.1 Stainless steel construction 9 gallon total capacity with a finished beer output of 5-6 gallons WiFi/Bluetooth Enabled RAPT digital temperature controller Automatic step mashing with 6 programmable stages 110-120V power and plug 12.5A Requires 20A circuit Dual heating elements (1000 watts and 500 watts) Stainless steel 1/2" ball valve for gravity draining or transferring via pump Immersion wort chiller included Stainless steel malt pipe/basket Stamped in volume markers Glass lid Adjustable lid clamps (do not use with glass lid in place - see below) Magnetic drive pump for recirculation, transfers, and cleaning Recirculation arm PPSU sight glass Bottom handle for easy lifting and pouring Rubber feet Temperature reads in °F or °C Approximately 32.75" H (with recirculation arm) x 12.5" D Recommended max. grain bill: 23.5 lbs AlcoEngine Still ready with the purchase of a Distillation Lid Pump Specs: Max Capacity: 2.9–3.1 gal/min Max Head: 4.9–6.8 ft. Poles: 2 Voltage: 110–120V-AC Frequency: 50–60Hz Power: 6 watts Current: 60 mA Speed: 2600–3000rpm Duty Cycle: Continuous Capacitor: 2µF Input/Output: 13mm barb Water Resistance: IPX2 Please note: due to patent restrictions in the United States, the malt pipe has been redesigned with one set of bottom feet. This model does not include the "two stage" malt pipe as advertised by KegLand and featured in previous MoreBeer! YouTube videos. Please Note: When removing the malt pipe to drain after mashing, it is important to do so slowly rather than in one swift pull. If the malt pipe is removed all at once when it is full of wort, it is possible for the draining wort to spray out and over the rim of the brewery through the perforated bottom. Remove the malt pipe slowly so that some of the wort can drain out before it is fully removed and set on its bottom feet. This can be done by hand on the 35L unit, but for the 65L and 100L units we highly recommend using the Pulley System for removing the malt pipe. Warning: Do not engage the adjustable lid clamps when brewing with the BrewZilla's standard glass lid. The clamps are only intended to be used with distillation lids or other metal accessories. With too much tension, it is possible for the lid clamps to break the glass lid when engaged. Warning: If you are going to use an extension cord with the BrewZilla, you must ensure that the cord is the correct gauge and properly rated to suit the power requirements of your brewery. See the reference chart below for the recommended gauge based on your unit and the length of cord you wish to use.   35L (110V) 35L (220V) 65L (220V) 100L (220V) 10 ft. 14 Gauge 14 Gauge 12 Gauge 10 Gauge 25 ft. 14 Gauge 14 Gauge 12 Gauge 10 Gauge 50 ft. 12 Gauge 12 Gauge 10 Gauge 8 Gauge

Read more less

Pro-Grade Construction: Made from high-quality 304 stainless steel with a welded dish bottom for complete drainage and easy cleaning. Integrated Grain Door: For effortless and complete grain removal. Sanitary Connections: Features sanitary welded TC ferrules for leak-free, professional-grade connections. Enhanced Usability: Includes silicone-gripped handles, a TC-ported lid for CIP, and raised legs for convenient access to lower ports and grain door. Fully Customizable: The kettle arrives without fittings or valves, giving you a blank canvas to customize with your preferred accessories. Elevate your homebrewing craft with the BrewBuilt Dish Bottom Kettle, specifically designed as the perfect mash tun. This professional-grade kettle is meticulously crafted from high-quality 304 stainless steel, ensuring durability and a lifetime of flawless brews. Experience the revolutionary welded dish bottom, engineered for unparalleled complete drainage, ensuring every precious drop of wort is utilized and cleanup becomes a breeze. This specialized BrewBuilt Kettle features a convenient grain door, making the removal of spent grains incredibly easy and efficient. High-quality sanitary welded TC Ferrules provide a lifetime of leak-free use and make sanitary connections effortless, a standard in professional breweries now accessible for homebrewing. Comfort and safety are prioritized with silicone-gripped handles to protect your hands from heat. The lid comes welded with a TC port, ready for CIP (Clean-in-Place) and other future accessories. For convenient access to lower ports, the kettle is raised on sturdy legs. BrewBuilt Kettles are the same high-performance kettles used in our Next Generation BrewSculptures, guaranteeing professional-grade results. Available in a wide range of popular homebrew sizes—10, 15, 20, 30, and 50 gallons—they cater to every brewing scale. Build Your Own Brewing System: This BrewBuilt Kettle provides the perfect foundation for your custom mashing setup. It does not include accessories, giving you the freedom to purchase the specific hardware you need to build a dedicated Mash Tun. Major Features for Brewers: High-Quality 304 stainless steel construction Welded Dish Bottom for complete drainage - easy cleaning, no loss Integrated Grain Door for easy removal of spent grains High-Quality sanitary welded TC Ferrules Handles with Silicone grips to avoid burning hands Lid comes welded with TC port for CIP and other accessories down the road Kettles are raised on legs for easy access to lower ports Same Kettles used in our Next Generation BrewSculptures Wide Range of homebrew sizes - 10, 15, 20, 30, 50 gal Please Note: This kettle is designed for customization. All necessary hardware—including heating elements, valves, thermowells, and clamps—must be purchased separately to build your desired brewing system.  

Read more less

Stop stirring your wort with a spoon and allow the BrewZilla's internal pump to do the work with this new Whirlpool Arm accessory. Fits all sizes of BrewZilla. The whirlpool arm fits onto the existing recirculation pipe with a stainless steel male camlock fitting. The BrewZilla's internal magnetic pump will aid in circulating your wort for better hop extraction in the whirlpool stage, as well as help collect the hot break into the center of the false bottom. Whirlpooling while cooling with the immersion heat exchanger will also speed up chilling times. Specifications: 304 Stainless Steel Fitted Male Camlock fitting Soft Safety Grip Length 520mm (20.5")   Kegland Part Number: KL14199

Read more less

Ss BrewTech has done it again, taking brewing equipment to an innovative next level.  These are a premium lineup of feature rich all Stainless Steel Brew Kettles, designed to keep you brewing for a lifetime.  What really sets this boil kettle apart from the rest is the first ever integrated trub dam and pick-up tube assembly that Ss has designed into the back of the 304 Ss 1/2" ball valve (3pc).  It is a brilliant little piece which will help with a more efficient whirlpool, leaving more trub in the kettle, and bringing more wort to the fermenter!  Other features include robust triclad bottom, internal gallon markings, and strong riveted handles with molded silicone grips that can hang the lid. Features: Heavy duty 18 gauge 304 Stainless 1.2 x 1.0 height to width ratio Triclad bottom - no scorching! Internal etched gallon markings (starting at 1 gal!) Thermometer port High Quality Weldless Fittings Robust riveted silicone handles for safety Hang lid on side handles Optional coupling for thermometer Dimensions: 13.4" H x 11" W 5.5 Gallons total volume

Read more less

A stable mash temp is one of the most important elements of the brewing process. The Ss Brewtech InfuSsion Mash Tun is the perfect choice for brewer’s looking to upgrade their aging plastic cooler. It’s built to last, made exclusively of 304 stainless steel and designed for those who want professional grade equipment and features for their home brewery. The double walled construction with injected high density foam insulation is incredible at mitigating temp loss and holding temperatures stable throughout the duration of a typical mash rest. The venerable InfuSsion Mash Tun has been updated with TC ports throughout for easy integration with the rest of the Ss Brewtech line up. Additionally, the InfuSsion Mash Tun is the first Ss product to be released with the Patent Pending Pure Flow Valve platform. Fully sanitary, easy to clean, and micro adjustable Pure Flow valves are designed as the ultimate brewing valve. Pro-Inspired Pro features like a 5° sloped floor with center drain, zero deadspace design, etched volume markings, integrated thermowell, thermometer, and the ability to incorporate mash recirculation result in the most thoroughly engineered and efficient mash tun available to homebrewers.  Upgradable The InfuSsion Mash Tun is now equipped with a 3/4" TC recirculation bulkhead which allows quick installation of optional accessories such as the vorlauf attachment or a recirculation manifold. Pure Flow Valve With a clean slate, the Ss Engineering Team took a stab at creating the perfect sanitary valve for brewing. The foundation of the Micro Adjust Valve is a removable silicone membrane that seamlessly integrates TC gasket geometry. This ingenious design provides a 100% sanitary environment where beer makes contact with nothing except pure silicone while inside the valve. Features: 304 Stainless steel construction 1” thick insulated side walls and lid Sanitary TC ports 5° sloped floor with center drain eliminates dead space Gasket sealed stainless steel false bottom 1.5" TC Pure Flow Valve 3/4" TC recirculation bulkhead Redesigned feet with locking screw  Redesigned LCD thermometer Etched volume markings gals/liters What's Included: InfuSsion Mash Tun LCD thermometer (°F/°C) Silicone thermometer boot (2) 1.5" TC clamps (2) 1.5" TC gaskets Pure Flow Valve 1.5" TC Thermowell Silicone plug for recirculation hole 3/4" TC recirculation bulkhead Perforated false bottom Silicone false bottom gasket   Lowest Price Guarantee, this item has MAP pricing so you can be confident you won't find it for less.

Read more less

Welded 1.5" tri-clamp ports for a lifetime of leak-free use Front & back positioned handles reduce the space needed to arrange multiple kettles in a horizontal system 304 stainless steel construction with mirror polish finish Notched lid provides cover while not interfering with immersion chillers, hop bags, or other accessories Choose from Boil Kettle, Hot Liquor Tank or Mash Tun configurations The Boil Kettle comes without fittings The Hot Liquor Tank includes a Kettle Maximizer and Thermometer with 2" Probe The Mash Tun includes a False Bottom Kit and Thermometer with 6" Probe Add your preferred Valve Hardware Pack below under You Might Also Need or purchase your own valve & fittings separately Designed for Brewing. Built to Last. BrewBuilt brew kettles are made from 304 stainless steel and offer an unparalleled mix of features for the price. At the very top of the list are two welded-in place tri-clamp couplers that offer a lifetime of leak free use. As you can imagine, welding in a coupler costs more than punching a hole and using a gasketed (i.e. weld-less) fitting. Welded fittings offer a permanent connection that to us is worth every penny. The second unique feature that we absolutely love about these brew kettles is the notched lid with silicone plug. This notch allows you so much flexibility; you can use an immersion chiller, one of our Ultimate Sparge Arms for mashing, tie off hop bags, take a temp reading during cooling, or whatever else we all can dream up. Our new T.C. kettles were designed to keep pace with the ever-evolving world of brewing technology. Tri-clamp fittings are standard fare in professional breweries, and they’ve been widely adopted in homebrewing as T.C. fermenters and pumps become more affordable and widely available. Tri-clamp fittings, also known as Tri-clover, allow you to make a sanitary connection that is free of nooks and crannies for contaminants to take hold. They are much easier to break down for cleaning compared to threaded connections, and they don’t require Teflon tape to make a watertight seal. T.C. fittings and accessories also give you the distinct advantage of being able to clean in place (CIP), so you don’t need to break down your entire system after every brew day. Configurations The base boil kettle comes without fittings so you can modify it the specific tri-clamp accessories that best suit your needs. Add one of the optional Brewing Kettle Valve Packs above which include your choice of valve and all the hardware you'll need to connect 1/2" ID transfer tubing, as well as an end cap to seal the top port if a thermometer or other accessory is not in place. The Hot Liquor Tank includes the base kettle plus a kettle maximizer for the bottom port and thermometer with 2" probe for the top port. Clamps and gaskets are included to attach the tri-clamp kettle maximizer and the thermometer. The Mash Tun includes the base kettle plus a false bottom kit for the bottom port and thermometer with 6" probe for the top port. Clamps and gaskets are included to attach the tri-clamp false bottom maximizer and the thermometer. Kettles do not come with a valve or additional fittings for the bottom port as standard. Add one of our pre-configured Valve Packs or purchase your preferred valve and fittings separately. This Brew Kettle has a lot to offer... Some other features we dig include the internal volume markers from the bottom to the top - so handy for instant reads. The silicone sleeved handles on the kettle and the lid are a cool feature to protect your hands. The tri-clad bottom with a 4mm core of aluminum sandwiched between two layers of stainless steel offers even heat distribution during the boil and also makes it a perfect choice for anyone wanting to use an induction burner. Beefy 304 Stainless These kettles are made from 304 grade stainless. That means you will have less corrosion issues than with a kettle made from lower grade 201 type stainless. We put these kettles through a corrosive salt water test in the MoreBeer! shop and they passed with flying colors. We also made sure the rivets and riveted handles were also made of stainless steel for a long term, trouble free life. The 10 and 15 gallon size are made from 1.0mm thick stainless steel. The 20, 30 and 50 gallon size are made with 1.2mm stainless - that's pretty thick stuff - and you will know it when you pick one up. Mirror Polish Finish The mirror polish finish isn’t just for making your Instagram feed pop! This extra slick finish is much easier to clean and sanitize than a standard brushed stainless kettle. Hop trub and other organic solids left behind after a brew day will have a hard time clinging to the interior surface and scrub away with ease. Size Ratios and Stuff All the BrewBuilt kettles follow the recent trend to a 1.2:1 ratio where the height is 1.2 times the diameter. This is a proven commercial ratio that has been adopted in homebrewing to achieve a more consistent 10% evaporation rate during the boil. We do like this ratio for boiling. For Mashing we would prefer a little bit shallower but that is a small compromise. Dimensions for a hot-liquor tank, if you are thinking brewing system down the road, are irrelevant as any ratio kettle will do. Features: Two welded T.C. couplers for a lifetime of leak free use Front & back oriented handles with silicone coated handles for heat protection Notched lid with silicone plug for flexibility 304 stainless steel construction for longevity 1.0mm (10 & 15 gal) or 1.2mm (20, 30 & 50 gal) thick side walls resist denting 4mm Tri-Clad Aluminum bottom sandwiched between two layers of stainless steel for no scorching Internally etched volume markers from top to bottom for easy reading 1.2:1 Ratio is optimal for boiling evaporation rate Lid is designed to conveniently hang from a handle Stainless handles with stainless rivets for secure lifting   Size Kettle ID (in.) Height (in.) 10 Gallon 13.78 16.54 15 Gallon 15.75 18.90 20 Gallon 17.72 21.26 30 Gallon 19.69 23.62 50 Gallon 23.62 28.30    

Read more less

Integrated 2" TC Port: Seamlessly connect a condenser or still top to recover hop oils, distill water, or experiment with spirits, transforming your kettle into a versatile system. Optimal Vapor Collection: The raised dome design facilitates efficient vapor collection and separation, ensuring high-quality distillation and enhanced performance. Secure & Durable Design: Crafted for a precise fit and a secure seal, this domed lid ensures optimal function and lasting durability for all your brewing and distilling needs. Bring your brewing to the next level with the BrewBuilt Domed Lid for Dish Bottom Kettles. This essential upgrade features a centered 2" tri-clamp (TC) port, giving you the flexibility to easily add a condenser or still top. Whether you're looking to recover hop oils, distill water, or experiment with spirits, this domed lid is designed for a seamless fit and optimal performance. The raised dome design allows for proper vapor collection and separation, while the high-quality construction ensures a secure seal. Transform your BrewBuilt kettle into a multi-functional powerhouse and unlock a new world of brewing possibilities.  

Read more less

Ss Brewtech took the features of pro brewing equipment and shrunk it down for the homebrewer with their new Brewmaster Edition Kettles. Built from high quality 304 stainless steel this kettle has it all. Rotatable racking arm and sight glass allow complete control of trub pick up. Also, the dish bottom and integrated fire box allow for faster boil times because of the increased surface area. All TC fittings are fully sanitary and the whirlpool coupler has a tangential inlet which provides a more effective whirlpool.  The BME Kettle from Ss Brewing Technologies has a feature set unmatched in the homebrewing market. Features: Integrated 1/2" ball valve with sight glass Tangential whirlpool inlet TIG welded TC ports Dish Bottom With FireBox for quicker boils Rotating racking arm Etched volume markings 1.2 mm 304 SS Construction With 2 mm SS Base 24 Gallon Full Volume 17.7" Ø x 26" Height Note: Not intended for use with induction burners!

Read more less

Ss Brewtech took the features of pro brewing equipment and shrunk it down for the homebrewer with their new Brewmaster Edition Kettles. Built from high quality 304 stainless steel this kettle has it all. Rotatable racking arm and sight glass allow complete control of trub pick up. Also, the dish bottom and integrated fire box allow for faster boil times because of the increased surface area. All TC fittings are fully sanitary and the whirlpool coupler has a tangential inlet which provides a more effective whirlpool.  The BME Kettle from Ss Brewing Technologies has a feature set unmatched in the homebrewing market. Features: Integrated 1/2" ball valve with sight glass Tangential whirlpool inlet Fully welded TC ports Dished bottom for faster boil times Rotatable racking arm Etched volume markings 1.2 mm 304 SS Construction w/ 2 mm SS Base 12 Gallon Full Volume 13.8" Ø x 20" Height Note: Not intended for use with induction burners!

Read more less

All the crucial features of a top-shelf brew kettle at an incredible price! These kettles are the perfect choice for new brewers leaving the kitchen stove and stepping up to the full boil brewing method Made from stainless steel throughout which is easy-to-clean and offers a lifetime of reliable use Two welded 1/2" ports for common threaded brewing accessories—ball valve and barb fitting are included for the bottom port Internal volume markers make it easy to measure pre boil volume and post boil volume Silicone grips made for comfortable, slip-free handling If you’re searching for a fully featured brew kettle but don't want to break the bank, the Brewmaster 8.5 Gallon Stainless Brew Kettle will certainly do the trick. Made of 100 percent stainless steel and available for a truly amazing price, this reliable brew kettle is perfect for first-time brewers and experienced home brewers alike. Two ½-inch couplers are welded to the side of the kettle, and the bottom coupler can even be threaded on the inside of the kettle to use with a diverter or a kettle tube screen. These kettles are upgraded with Silicone Grip Handles and Stamped volume markers on the inside, making brew day that much easier. Add an AG405 (domed false bottom) to this stainless brew kettle and you can even use it as a mash tun. Includes a ball valve and a threaded adpator to 3/8" barb for easily attaching transfer tubing. Also included is a thread 1/2" plug for the thermometer port. Thermometer is not included and can be added at any time. Features: 8.5 Gallon Stainless Steel Brewmaster Brewing Kettle Two Welded 1/2" Full Couplers allow for internal and external attachments Stainless 1/2" Full Port Ball Valve & nipple included for bottom Coupler Stainless 1/2" Plug included for top coupler Stamped Volume Markers Silicone Handle Grips Internal Threading allows for conversion to Mash Tun or addition of whole hop filters Internal Dimensions: 13.75" Tall x 13.75" Ø 1 mm thick walls Made from 201 Stainless Steel Approximate Internal Dimensions 13.75" tall 13.75" wide. This item does not work with induction burners A ball valve, nipple, and plug are included for the welded couplers. A thermometer, false bottom, or kettle screen can be added separately

Read more less

Used along with the Ss recirculation bulkhead, this fitting adds a 3/8" hose barb on your mash tun. It attaches with a 1/2" FPT knurled locking nut and is required if you are using the Ss recirculation manifold. Made from 304 stainless steel and silicone O-rings included.

Read more less

Recirculate wort in your boil kettle without sacrificing one of your tri-clamp ports. The BrewBuilt Whirlpool Return Fitting & Thermowell Offset kit allows you to use any tri-clamp kettle's thermometer port to recirculate wort while also taking temp readings. This kit is perfect for kettles that only have two tri-clamp ports—eliminating the need to drill out a hole in your kettle to add a third port for wort recirculation. Attach your preferred valve or tri-clamp fitting to the side inlet and, during whirlpool, draw wort from your bottom port and pump it back through the Whirlpool Return Fitting. Kit Includes: Whirlpool Return Fitting Thermowell Offset (1) 1.5" Tri-Clamp (1) 1.5" Tri-Clamp Gasket (EPDM)

Read more less

Hot side hop additions should stay in the kettle and out of the fermenter. Keep all that hop matter from transferring out with your wort using this Double Handle Hop Filter. At 6" diameter and 14" tall, this unit will do well with even the hoppiest beers you brew. Conveniently hangs on the inside of your kettle so you can remove it at any point if needed. The double handle design will keep the basket nice and steady compared to single handle units. This is a great alternative to hop bags which have the potential to decrease hop utilization. While using this filter basket you can add hops directly to your kettle for maximum wort exposure. Brewing all grain beer? This hop filter is also perfect as secondary filter when transferring wort from your mash tun to your boil kettle. If any tiny bits make it past your false bottom, the hop filter will catch them. Made from 304 stainless steel Double handle design 14" H x 6" Ø  

Read more less

The Ultimate BrewZilla Combo Pack! Get the Gen 4 BrewZilla & our most highly recommended accessories at an unbeatable price! Includes all of our favorite accessories for the BrewZilla including the Neoprene Jacket to speed up heating times, Hop Spider to keep vegetal matter out of your wort, and Chilling Connection Kit so you're ready to use the Immersion Chiller out of the box We think all BrewZilla brewers will eventually upgrade their systems with these accessories, so buy them together and reap the savings! Also available in 110V (AG581) Combo Pack Includes: BrewZilla Brewing System | Gen 4 | 9.25G | 220V Neoprene Jacket Hop Spider Wort Chiller Connection Kit Gen 4 BrewZilla All-in-One Brewing System WiFi / Bluetooth enabled RAPT Controller tracks your brewday and automatically uploads detailed information to the RAPT portal The top mounted RAPT Controller can be tilted upward for easy viewing, or detached from the unit to mount it on the wall or placed on your bench Mirror polished dome shaped bottom with center drain — get every last bit of wort into your fermenter while the perforated bottom screen filters out 95% of hot break and hop matter Make larger batches or higher gravity beers! BrewZilla offers the largest malt pipe capacity for units in its size range, and the Gen 4 unit has a 30% larger malt pipe compared to the previous generation Perforated bottom on the newly designed malt pipe allows for improved mash recirculation flow without sacrificing efficiency Element power percentage can be adjusted via the RAPT Controller. Go full power to heat up quickly, or dial it down so you don’t overshoot your strike water temp The built-in pump is plumbed to both the recirculation and arm and the bottom ball valve. Recirculate wort during your mash, then close the recirculation valve and pump wort to your fermenter via the bottom valve Pair with the RAPT-enabled Bluetooth Thermometer, allowing your BrewZilla to calculate a core mash temperature reading and more accurately control temperatures and mash steps More RAPT-enabled accessories are coming, and future firmware updates can be downloaded to the RAPT Controller itself over the internet WiFi/Bluetooth Enabled RAPT Controller The RAPT Controller is mounted to the top of the boiler body, allowing for easy operation when you have the unit set on the ground. The controller can be tilted upwards to give you an even better view, or it can be removed from the BrewZilla entirely if you’d prefer to mount the controller on your wall or lay it down on a workbench. From the controller, you’ll orchestrate your entire brew day. Program mash steps, dial in element power, and operate the integrated pump all from one screen. But the RAPT Controller is much more than a beautiful, full-color display switch board. Once synced to the RAPT Portal, you’ll be able to track, record and monitor your brews online. No need for handwriting notes or punching brew day details into your phone – all of the data from your brew is automatically logged to your portal profile. This information doesn’t just include your mash profile; it also captures detailed information about your element power and pump activity, opening the door for very precise repeatability. And the RAPT Portal isn’t just a digital archive for your brew days. With your BrewZilla powered on, you can control your brewery from virtually anywhere using your phone’s web browser. Not sure when you’ll be home from work or your kid’s ball game going into extra innings? No problem! Before you head out, simply log into the RAPT Portal from your phone and tell the BrewZilla to start heating your strike water. Along with remote control, the portal enables you to program alarms and push notifications for all of your boil additions. We’ve all been caught up with a side task and failed to throw in that yeast nutrient or clarifying agent at the end of the boil, but the BrewZilla has the back of even the most forgetful brewer! But wait, there’s more! In addition to WiFi connectivity, the RAPT Controller is also a Bluetooth gateway device. KegLand is currently developing various Bluetooth devices such as the Bluetooth Beacon Thermometer and other sensors which will be compatible with your brewery upon release. The RAPT Controller is able to receive information from Bluetooth Low Energy (BLE) devices, adjusting its processes based on this new stream of information while simultaneously logging it to your RAPT Portal. With the Bluetooth Beacon Thermometer, for example, you’ll be able to feed temperature readings from the top of your mash bed to the controller. The controller will then compare this reading with the main temp probe reading at the base of the kettle and adjust element cycling based on these combined readings. Finally, the RAPT Controller WiFi connectivity allows you to update the controller’s firmware with a single click. Take advantage of new features and accessories as soon as they become available by simply keeping your BrewZilla connected to your local WiFi network. And again, the WiFi is already built-in! No need to come back for an expensive add-on accessory down the road. High Capacity Malt Pipe With an approximately 23.5 lb capacity, the BrewZilla can mash nearly 50% more grain than similar sized models of the Anvil Foundry and Grainfather G30. If you want to fill your fermenter with more than a 5-gallon batch worth of wort, or brew the highest gravity beer recipes, the BrewZilla is the brewhouse for the job. And the included malt pipe is just the beginning. If you want to expand your brewery’s grain capacity even further, KegLand makes Boiler Extension Kits and Extended Malt Pipes for that very purpose. The malt pipe features a perforated section at the bottom which improves mash recirculation flow without sacrificing efficiency. Concave Base with Center Draining Leave no wort behind! The concave base with center drain means you’ll be able to extract every last drop of wort to your fermenter. If you’ve brewed in a traditional flat bottom kettle, this center drain may be a bit perplexing at first. Many brewers are used to whirlpooling after the boil to pull hop matter into the center of the kettle, then transfer out using a pick-up tube that pulls from the kettle wall in order to avoid sucking up the solids. But fear not! One of the key features of the BrewZilla is the false bottom protection screen. This screen avoids the need for doing a whirlpool, filtering wort as it transfers and blocking more than 95% of hops and hot break from getting sucked into the pump. This not only prevents blocked pump issues, it also increases the efficiency of your brewhouse by eliminating kettle loss from wort that may have otherwise been left behind. Ultra Low Watt Density Elements The concave base on the BrewZilla also allowed for larger heating elements with significantly lower watt density than other breweries. When a lot of energy is coming off of a small element, the local temperature near the element can be so high that it scorches the wort and causes caramelization. Lower watt density essentially means you can produce lighter color beers that would otherwise have fallen victim to caramelization effect. It also reduces that chance of boilovers and reduces stress on the elements which extends their life expectancy. Easy Access Built-In Pump The built-in pump allows you to recirculate your wort during the mash for improved efficiency and more even temperature distribution. But it can also be used to transfer your wort from kettle to fermenter rather than relying on a gravity feed, and with the optional CIP Rotar, you can used the pump to clean your BrewZilla (or fermenter) after every use. During your brew day you’ll be able to control the pump from the RAPT Controller with a dedicated button for turning the pump on and off. Another feature you’ll find on the controller is adjusting the pump flow. This doesn’t control the actual volume of the flow (you can do that from the ball valve located on the recirculation arm), but rather cycles the pump on and off automatically based on your setting. At 100%, the pump remains on continuously. But at 80%, the pump will cycle to be on 80% of the time and off 20% of the time. This may not be a feature that every brewer thinks they need, but it’s an excellent way to avoid running the pump dry accidentally, as the time the pump is off allows recirculating wort to filter through the grain bed and back into the pump inlet. If you flip over the boiler, you’ll find the magnetic drive pump and all the plumbing is right at your fingertips. This means you don’t have to disassemble the base in order to access the pump for cleaning or maintenance if required. It also means the plumbing can be changed more easily too. For instance, the unit comes as standard with the plumbing from the pump feeding both the recirculation arm and the transfer valve, but you change this so the tap outlet bypasses the pump if you prefer. MoreBeer!'s Final Word We’ve been selling all-in-one brewing systems ever since they first hit the market, and we have to say that the Gen 4 BrewZilla is not only the most feature-packed unit ever made, it’s also offered at an incredibly competitive price point when compared to other systems. You’ll get all of the cutting edge Bluetooth technology you’d get with the Grainfather and at an exceptionally lower price tag. Plus, you get the WiFi capabilities as standard, rather than as a $100 add-on accessory. When it comes to mash recirculation, that’s yet another built-in feature on the BrewZilla, and the pump can also be used for transferring and CIP cleaning. The Foundry has a great starting price, but if you want to unlock its full potential, you’ll need to spend another $100 for the recirculation pump kit. What’s more, no other system in the same ‘weight class’ has the same grain capacity. And if the standard capacity isn’t quite enough, the BrewZilla can be easily upgraded with a Boiler Body Extension Kit and Extended Malt Pipe. When you purchase the BrewZilla, you can feel confident that you’re investing in a top shelf system and all of the critical features you’re expecting will be included. Perfect for Distillation If you want to expand your lineup of homemade libations to offer Spirits in addition to Ales & Lagers, the BrewZilla makes an excellent pot still! Add the Distillation Lid upgrade and pair it with an AlcoEngine Copper Reflux Condenser or Copper Pot Still Top. AlcoEngine Stills have been selling on the home market for years and offer some of the most affordable, beginner-friendly stills you'll find. Features: Gen 4.1 Stainless steel construction 9 gallon total capacity with a finished beer output of 5-6 gallons WiFi/Bluetooth Enabled RAPT digital temperature controller Automatic step mashing with 6 programmable stages 220-240V power NEMA 6-30P plug Requires NEMA 6-30R receptacle Requires 11 amps from 30 amp circuit Dual heating elements (1900 watts and 500 watts) Stainless steel 1/2" ball valve for gravity draining or transferring via pump Immersion wort chiller included Stainless steel malt pipe/basket Stamped in volume markers Glass lid Adjustable lid clamps (do not use with glass lid in place - see below) Magnetic drive pump for recirculation, transfers, and cleaning Recirculation arm PPSU sight glass Bottom handle for easy lifting and pouring Rubber feet Temperature reads in °F or °C Approximately 32.75" H (with recirculation arm) x 12.5" D Recommended max. grain bill: 23.5 lbs AlcoEngine Still ready with the purchase of a Distillation Lid Pump Specs: Max Capacity: 2.9–3.1 gal/min Max Head: 4.9–6.8 ft. Poles: 2 Voltage: 220–240V-AC Frequency: 50–60Hz Power: 6 watts Current: 60 mA Speed: 2600–3000rpm Duty Cycle: Continuous Capacitor: 2µF Input/Output: 13mm barb Water Resistance: IPX2 Please note: due to patent restrictions in the United States, the malt pipe has been redesigned with one set of bottom feet. This model does not include the "two stage" malt pipe as advertised by KegLand and featured in previous MoreBeer! YouTube videos. Please Note: When removing the malt pipe to drain after mashing, it is important to do so slowly rather than in one swift pull. If the malt pipe is removed all at once when it is full of wort, it is possible for the draining wort to spray out and over the rim of the brewery through the perforated bottom. Remove the malt pipe slowly so that some of the wort can drain out before it is fully removed and set on its bottom feet. This can be done by hand on the 35L unit, but for the 65L and 100L units we highly recommend using the Pulley System for removing the malt pipe. Warning: Do not engage the adjustable lid clamps when brewing with the BrewZilla's standard glass lid. The clamps are only intended to be used with distillation lids or other metal accessories. With too much tension, it is possible for the lid clamps to break the glass lid when engaged. Warning: If you are going to use an extension cord with the BrewZilla, you must ensure that the cord is the correct gauge and properly rated to suit the power requirements of your brewery. See the reference chart below for the recommended gauge based on your unit and the length of cord you wish to use. 35L (110V) 35L (220V) 65L (220V) 100L (220V) 10 ft. 14 Gauge 14 Gauge 12 Gauge 10 Gauge 25 ft. 14 Gauge 14 Gauge 12 Gauge 10 Gauge 50 ft. 12 Gauge 12 Gauge 10 Gauge 8 Gauge

Read more less

LCD Temp Display Module for Mash Tun and FTSs units. Displays in Fahrenheit. Features: Digital temp sensor Easy to read LCD display Batteries included Silicone rubber housing Custom tooled to use with Chronicals

Read more less

All the crucial features of a top-shelf brew kettle at an incredible price! These kettles are the perfect choice for new brewers leaving the kitchen stove and stepping up to the full boil brewing method Made from stainless steel throughout which is easy-to-clean and offers a lifetime of reliable use Two welded 1/2" ports for common threaded brewing accessories—ball valve and barb fitting are included for the bottom port Internal volume markers make it easy to measure pre boil volume and post boil volume Silicone grips made for comfortable, slip-free handling If you’re searching for a fully featured brew kettle but don't want to break the bank, the Brewmaster 8.5 Gallon Stainless Brew Kettle will certainly do the trick. Made of 100 percent stainless steel and available for a truly amazing price, this reliable brew kettle is perfect for first-time brewers and experienced home brewers alike. Two ½-inch couplers are welded to the side of the kettle, and the bottom coupler can even be threaded on the inside of the kettle to use with a diverter or a kettle tube screen. These kettles are upgraded with Silicone Grip Handles and Stamped volume markers on the inside, making brew day that much easier. Add an AG405 (domed false bottom) to this stainless brew kettle and you can even use it as a mash tun. Includes a ball valve and a threaded adpator to 3/8" barb for easily attaching transfer tubing. Also included is a thread 1/2" plug for the thermometer port. Thermometer is not included and can be added at any time. Features: 8.5 Gallon Stainless Steel Brewmaster Brewing Kettle Two Welded 1/2" Full Couplers allow for internal and external attachments Stainless 1/2" Full Port Ball Valve & nipple included for bottom Coupler Stainless 1/2" Plug included for top coupler Stamped Volume Markers Silicone Handle Grips Internal Threading allows for conversion to Mash Tun or addition of whole hop filters Internal Dimensions: 13.75" Tall x 13.75" Ø 1 mm thick walls Made from 201 Stainless Steel Approximate Internal Dimensions 13.75" tall 13.75" wide. This item does not work with induction burners A ball valve, nipple, and plug are included for the welded couplers. A thermometer, false bottom, or kettle screen can be added separately

Read more less

All the crucial features of a top-shelf brew kettle at an incredible price! Perfectly sized for 15 gallon batch brewers Made from stainless steel throughout which is easy-to-clean and offers a lifetime of reliable use Two welded 1/2" ports for common threaded brewing accessories—ball valve and barb fitting are included for the bottom port Internal volume markers make it easy to measure pre boil volume and post boil volume Silicone grips made for comfortable, slip-free handling If you’re searching for a fully featured brew kettle but don't want to break the bank, the Brewmaster 18.5 Gallon Stainless Brew Kettle will certainly do the trick. Made of 100 percent stainless steel and available for a truly amazing price, this reliable brew kettle is perfect for first-time brewers and experienced home brewers alike. Two ½-inch couplers are welded to the side of the kettle, and the bottom coupler can even be threaded on the inside of the kettle to use with a diverter or a kettle tube screen. These kettles are upgraded with Silicone Grip Handles and Stamped volume markers on the inside, making brew day that much easier. Includes a ball valve and a threaded adpator to 3/8" barb for easily attaching transfer tubing. Also included is a thread 1/2" plug for the thermometer port. Thermometer is not included and can be added at any time. Features: 18.5 Gallon Stainless Steel Brewmaster Brewing Kettle Two Welded 1/2" Full Couplers allow for internal and external attachments Stainless 1/2" Full Port Ball Valve & nipple included for bottom Coupler Stainless 1/2" Plug included for top coupler Stamped Volume Markers Silicone Handle Grips Internal Threading allows for conversion to Mash Tun or addition of whole hop filters Internal Dimensions: 18" Tall x 17.75" Ø Made from 201 Stainless Steel Approximate Internal Dimensions 18" tall 17.75" wide. 1.2 mm thick walls This item does not work with induction burners A ball valve, nipple, and plug are included for the welded couplers. A thermometer, or kettle screen can be added separately

Read more less

Elevate your brewing game with the Gen 4 BrewZilla. This cutting-edge system combines innovative features like wireless connectivity via WiFi & Bluetooth, allowing you to control and monitor your brew day, ensuring precision, convenience, and exceptional beer batch after batch! WiFi / Bluetooth enabled RAPT Controller tracks your brewday and automatically uploads detailed information to the RAPT portal The top mounted RAPT Controller can be tilted upward for easy viewing, or detached from the unit to mount it on the wall or placed on your bench Mirror polished dome shaped bottom with center drain -- get every last bit of wort into your fermenter while the perforated bottom screen filters out 95% of hot break and hop matter Make larger batches or higher gravity beers! BrewZilla offers the largest malt pipe capacity for units in its size range, and the Gen 4 unit has a 30% larger malt pipe compared to the previous generation Perforated bottom on the newly designed malt pipe allows for improved mash recirculation flow without sacrificing efficiency Element power percentage can be adjusted via the RAPT Controller. Go full power to heat up quickly, or dial it down so you don't overshoot your strike water temp The built-in pump is plumbed to both the recirculation and arm and the bottom ball valve. Recirculate wort during your mash, then close the recirculation valve and pump wort to your fermenter via the bottom valve Pair with the RAPT-enabled Bluetooth Thermometer, allowing your BrewZilla to calculate a core mash temperature reading and more accurately control temperatures and mash steps More RAPT-enabled accessories are coming, and future firmware updates can be downloaded to the RAPT Controller itself over the internet WiFi/Bluetooth Enabled RAPT Controller The RAPT Controller is mounted to the top of the boiler body, allowing for easy operation when you have the unit set on the ground. The controller can be tilted upwards to give you an even better view, or it can be removed from the BrewZilla entirely if you'd prefer to mount the controller on your wall or lay it down on a workbench. From the controller, you'll orchestrate your entire brew day. Program mash steps, dial in element power, and operate the integrated pump all from one screen. But the RAPT Controller is much more than a beautiful, full-color display switch board. Once synced to the RAPT Portal, you'll be able to track, record and monitor your brews online. No need for handwriting notes or punching brew day details into your phone -- all of the data from your brew is automatically logged to your portal profile. This information doesn't just include your mash profile; it also captures detailed information about your element power and pump activity, opening the door for very precise repeatability. And the RAPT Portal isn't just a digital archive for your brew days. With your BrewZilla powered on, you can control your brewery from virtually anywhere using your phone's web browser. Not sure when you'll be home from work or your kid's ball game going into extra innings? No problem! Before you head out, simply log into the RAPT Portal from your phone and tell the BrewZilla to start heating your strike water. Along with remote control, the portal enables you to program alarms and push notifications for all of your boil additions. We've all been caught up with a side task and failed to throw in that yeast nutrient or clarifying agent at the end of the boil, but the BrewZilla has the back of even the most forgetful brewer! But wait, there's more! In addition to WiFi connectivity, the RAPT Controller is also a Bluetooth gateway device. KegLand is currently developing various Bluetooth devices such as the Bluetooth Beacon Thermometer and other sensors which will be compatible with your brewery upon release. The RAPT Controller is able to receive information from Bluetooth Low Energy (BLE) devices, adjusting its processes based on this new stream of information while simultaneously logging it to your RAPT Portal. With the Bluetooth Beacon Thermometer, for example, you'll be able to feed temperature readings from the top of your mash bed to the controller. The controller will then compare this reading with the main temp probe reading at the base of the kettle and adjust element cycling based on these combined readings. Finally, the RAPT Controller WiFi connectivity allows you to update the controller's firmware with a single click. Take advantage of new features and accessories as soon as they become available by simply keeping your BrewZilla connected to your local WiFi network. And again, the WiFi is already built-in! No need to come back for an expensive add-on accessory down the road. High Capacity Malt Pipe With an approximately 23.5 lb capacity, the BrewZilla can mash nearly 50% more grain than similar sized models of the Anvil Foundry and Grainfather G30. If you want to fill your fermenter with more than a 5-gallon batch worth of wort, or brew the highest gravity beer recipes, the BrewZilla is the brewhouse for the job. And the included malt pipe is just the beginning. If you want to expand your brewery's grain capacity even further, KegLand makes Boiler Extension Kits and Extended Malt Pipes for that very purpose. The malt pipe features a perforated section at the bottom which improves mash recirculation flow without sacrificing efficiency. Concave Base with Center Draining Leave no wort behind! The concave base with center drain means you'll be able to extract every last drop of wort to your fermenter. If you've brewed in a traditional flat bottom kettle, this center drain may be a bit perplexing at first. Many brewers are used to whirlpooling after the boil to pull hop matter into the center of the kettle, then transfer out using a pick-up tube that pulls from the kettle wall in order to avoid sucking up the solids. But fear not! One of the key features of the BrewZilla is the false bottom protection screen. This screen avoids the need for doing a whirlpool, filtering wort as it transfers and blocking more than 95% of hops and hot break from getting sucked into the pump. This not only prevents blocked pump issues, it also increases the efficiency of your brewhouse by eliminating kettle loss from wort that may have otherwise been left behind. Ultra Low Watt Density Elements The concave base on the BrewZilla also allowed for larger heating elements with significantly lower watt density than other breweries. When a lot of energy is coming off of a small element, the local temperature near the element can be so high that it scorches the wort and causes caramelization. Lower watt density essentially means you can produce lighter color beers that would otherwise have fallen victim to caramelization effect. It also reduces that chance of boilovers and reduces stress on the elements which extends their life expectancy. Easy Access Built-In Pump The built-in pump allows you to recirculate your wort during the mash for improved efficiency and more even temperature distribution. But it can also be used to transfer your wort from kettle to fermenter rather than relying on a gravity feed, and with the optional CIP Rotar, you can used the pump to clean your BrewZilla (or fermenter) after every use. During your brew day you'll be able to control the pump from the RAPT Controller with a dedicated button for turning the pump on and off. Another feature you'll find on the controller is adjusting the pump flow. This doesn't control the actual volume of the flow (you can do that from the ball valve located on the recirculation arm), but rather cycles the pump on and off automatically based on your setting. At 100%, the pump remains on continuously. But at 80%, the pump will cycle to be on 80% of the time and off 20% of the time. This may not be a feature that every brewer thinks they need, but it's an excellent way to avoid running the pump dry accidentally, as the time the pump is off allows recirculating wort to filter through the grain bed and back into the pump inlet. If you flip over the boiler, you'll find the magnetic drive pump and all the plumbing is right at your fingertips. This means you don't have to disassemble the base in order to access the pump for cleaning or maintenance if required. It also means the plumbing can be changed more easily too. For instance, the unit comes as standard with the plumbing from the pump feeding both the recirculation arm and the transfer valve, but you change this so the tap outlet bypasses the pump if you prefer. MoreBeer!'s Final Word We've been selling all-in-one brewing systems ever since they first hit the market, and we have to say that the Gen 4 BrewZilla is not only the most feature-packed unit ever made, it's also offered at an incredibly competitive price point when compared to other systems. You'll get all of the cutting edge Bluetooth technology you'd get with the Grainfather and at an exceptionally lower price tag. Plus, you get the WiFi capabilities as standard, rather than as a $100 add-on accessory. When it comes to mash recirculation, that's yet another built-in feature on the BrewZilla, and the pump can also be used for transferring and CIP cleaning. The Foundry has a great starting price, but if you want to unlock its full potential, you'll need to spend another $100 for the recirculation pump kit. What's more, no other system in the same 'weight class' has the same grain capacity. And if the standard capacity isn't quite enough, the BrewZilla can be easily upgraded with a Boiler Body Extension Kit and Extended Malt Pipe. When you purchase the BrewZilla, you can feel confident that you're investing in a top shelf system and all of the critical features you're expecting will be included. Perfect for Distillation If you want to expand your lineup of homemade libations to offer Spirits in addition to Ales & Lagers, the BrewZilla makes an excellent pot still! Add the Distillation Lid upgrade and pair it with an AlcoEngine Copper Reflux Condenser or Copper Pot Still Top. AlcoEngine Stills have been selling on the home market for years and offer some of the most affordable, beginner-friendly stills you'll find. Features: Gen 4.1 Stainless steel construction 9 gallon total capacity with a finished beer output of 5-6 gallons WiFi/Bluetooth Enabled RAPT digital temperature controller Automatic step mashing with 6 programmable stages 110-120V power and plug 12.5A Requires 20A circuit Dual heating elements (1000 watts and 500 watts) Stainless steel 1/2" ball valve for gravity draining or transferring via pump Immersion wort chiller included Stainless steel malt pipe/basket Stamped in volume markers Glass lid Adjustable lid clamps (do not use with glass lid in place - see below) Magnetic drive pump for recirculation, transfers, and cleaning Recirculation arm PPSU sight glass Bottom handle for easy lifting and pouring Rubber feet Temperature reads in °F or °C Approximately 32.75" H (with recirculation arm) x 12.5" D Recommended max. grain bill: 23.5 lbs AlcoEngine Still ready with the purchase of a Distillation Lid Pump Specs: Max Capacity: 2.9–3.1 gal/min Max Head: 4.9–6.8 ft. Poles: 2 Voltage: 110–120V-AC Frequency: 50–60Hz Power: 6 watts Current: 60 mA Speed: 2600–3000rpm Duty Cycle: Continuous Capacitor: 2µF Input/Output: 13mm barb Water Resistance: IPX2 You Will Need: 2' of H985 1/2" ID Silicone tubing for sparging and draining. To connect included Chiller: (20') of D1710 1/2" ID beverage tubing (or whatever length required, (3) H950hose clamps and (1) brass hose by thread adaptor (H508). These items come in the Wort Chiller Connection Kit, add the kit to your cart and use code ZILLAKIT at checkout. KegLand Part Number: KL3276 Please note: due to patent restrictions in the United States, the malt pipe has been redesigned with one set of bottom feet. This model does not include the "two stage" malt pipe as advertised by KegLand and featured in previous MoreBeer! YouTube videos. Please Note: When removing the malt pipe to drain after mashing, it is important to do so slowly rather than in one swift pull. If the malt pipe is removed all at once when it is full of wort, it is possible for the draining wort to spray out and over the rim of the brewery through the perforated bottom. Remove the malt pipe slowly so that some of the wort can drain out before it is fully removed and set on its bottom feet. This can be done by hand on the 35L unit, but for the 65L and 100L units we highly recommend using the Pulley System for removing the malt pipe. Warning: Do not engage the adjustable lid clamps when brewing with the BrewZilla's standard glass lid. The clamps are only intended to be used with distillation lids or other metal accessories. With too much tension, it is possible for the lid clamps to break the glass lid when engaged. Warning: If you are going to use an extension cord with the BrewZilla, you must ensure that the cord is the correct gauge and properly rated to suit the power requirements of your brewery. See the reference chart below for the recommended gauge based on your unit and the length of cord you wish to use.   35L (110V) 35L (220V) 65L (220V) 100L (220V) 10 ft. 14 Gauge 14 Gauge 12 Gauge 10 Gauge 25 ft. 14 Gauge 14 Gauge 12 Gauge 10 Gauge 50 ft. 12 Gauge 12 Gauge 10 Gauge 8 Gauge   RAPT Gen 4 BrewZilla | User Manual

Read more less

The Ultimate Grain to Glass Combo Pack! Get the Gen 4 BrewZilla & FermZilla Easy-Grip Tri-Conical with all the best accessories at an unbeatable price! Brew extract or all grain batches on the BrewZilla; ferment, carbonate, and serve from the FermZilla. Everything you need from Grain to Glass! Comes with all of the most highly recommended accessories for the BrewZilla, including the Neoprene Jacket to speed up heating times, Hop Spider to keep vegetal matter out of your wort, and Chilling Connection kit so you're ready to use the Immersion Chiller out of the box Includes some of our favorite accessories for the FermZilla, such as the Pressure Kit with Floating Dip Tube so you're always racking the clearest beer and the Duotight BlowTie 2 for pressure fermentations and flow control keg transfers Over $100 savings when purchasing this kit bundle compared to buying everything piece-by-piece! Also available in 220V (AG582) You can search high and low, but you won't find a better deal than the BrewZilla Ultimate Grain to Glass Combo Pack! Combo Pack Includes: BrewZilla Brewing System | Gen 4.1 | 9.25G | 110V Neoprene Jacket Hop Spider Wort Chiller Connection Kit FermZilla Tri-Conical Fermenter | Gen 3.2 | 7.1G Plastic Pressure Kit w/ Floating Dip Tube Duotight BlowTie 2 Spunding Valve Insulating Jacket Gen 4 BrewZilla All-in-One Brewing System WiFi / Bluetooth enabled RAPT Controller tracks your brewday and automatically uploads detailed information to the RAPT portal The top mounted RAPT Controller can be tilted upward for easy viewing, or detached from the unit to mount it on the wall or placed on your bench Mirror polished dome shaped bottom with center drain — get every last bit of wort into your fermenter while the perforated bottom screen filters out 95% of hot break and hop matter Make larger batches or higher gravity beers! BrewZilla offers the largest malt pipe capacity for units in its size range, and the Gen 4 unit has a 30% larger malt pipe compared to the previous generation Perforated bottom on the newly designed malt pipe allows for improved mash recirculation flow without sacrificing efficiency Element power percentage can be adjusted via the RAPT Controller. Go full power to heat up quickly, or dial it down so you don’t overshoot your strike water temp The built-in pump is plumbed to both the recirculation and arm and the bottom ball valve. Recirculate wort during your mash, then close the recirculation valve and pump wort to your fermenter via the bottom valve Pair with the RAPT-enabled Bluetooth Thermometer, allowing your BrewZilla to calculate a core mash temperature reading and more accurately control temperatures and mash steps More RAPT-enabled accessories are coming, and future firmware updates can be downloaded to the RAPT Controller itself over the internet WiFi/Bluetooth Enabled RAPT Controller The RAPT Controller is mounted to the top of the boiler body, allowing for easy operation when you have the unit set on the ground. The controller can be tilted upwards to give you an even better view, or it can be removed from the BrewZilla entirely if you’d prefer to mount the controller on your wall or lay it down on a workbench. From the controller, you’ll orchestrate your entire brew day. Program mash steps, dial in element power, and operate the integrated pump all from one screen. But the RAPT Controller is much more than a beautiful, full-color display switch board. Once synced to the RAPT Portal, you’ll be able to track, record and monitor your brews online. No need for handwriting notes or punching brew day details into your phone – all of the data from your brew is automatically logged to your portal profile. This information doesn’t just include your mash profile; it also captures detailed information about your element power and pump activity, opening the door for very precise repeatability. And the RAPT Portal isn’t just a digital archive for your brew days. With your BrewZilla powered on, you can control your brewery from virtually anywhere using your phone’s web browser. Not sure when you’ll be home from work or your kid’s ball game going into extra innings? No problem! Before you head out, simply log into the RAPT Portal from your phone and tell the BrewZilla to start heating your strike water. Along with remote control, the portal enables you to program alarms and push notifications for all of your boil additions. We’ve all been caught up with a side task and failed to throw in that yeast nutrient or clarifying agent at the end of the boil, but the BrewZilla has the back of even the most forgetful brewer! But wait, there’s more! In addition to WiFi connectivity, the RAPT Controller is also a Bluetooth gateway device. KegLand is currently developing various Bluetooth devices such as the Bluetooth Beacon Thermometer and other sensors which will be compatible with your brewery upon release. The RAPT Controller is able to receive information from Bluetooth Low Energy (BLE) devices, adjusting its processes based on this new stream of information while simultaneously logging it to your RAPT Portal. With the Bluetooth Beacon Thermometer, for example, you’ll be able to feed temperature readings from the top of your mash bed to the controller. The controller will then compare this reading with the main temp probe reading at the base of the kettle and adjust element cycling based on these combined readings. Finally, the RAPT Controller WiFi connectivity allows you to update the controller’s firmware with a single click. Take advantage of new features and accessories as soon as they become available by simply keeping your BrewZilla connected to your local WiFi network. And again, the WiFi is already built-in! No need to come back for an expensive add-on accessory down the road. High Capacity Malt Pipe With an approximately 23.5 lb capacity, the BrewZilla can mash nearly 50% more grain than similar sized models of the Anvil Foundry and Grainfather G30. If you want to fill your fermenter with more than a 5-gallon batch worth of wort, or brew the highest gravity beer recipes, the BrewZilla is the brewhouse for the job. And the included malt pipe is just the beginning. If you want to expand your brewery’s grain capacity even further, KegLand makes Boiler Extension Kits and Extended Malt Pipes for that very purpose. The malt pipe features a perforated section at the bottom which improves mash recirculation flow without sacrificing efficiency. Concave Base with Center Draining Leave no wort behind! The concave base with center drain means you’ll be able to extract every last drop of wort to your fermenter. If you’ve brewed in a traditional flat bottom kettle, this center drain may be a bit perplexing at first. Many brewers are used to whirlpooling after the boil to pull hop matter into the center of the kettle, then transfer out using a pick-up tube that pulls from the kettle wall in order to avoid sucking up the solids. But fear not! One of the key features of the BrewZilla is the false bottom protection screen. This screen avoids the need for doing a whirlpool, filtering wort as it transfers and blocking more than 95% of hops and hot break from getting sucked into the pump. This not only prevents blocked pump issues, it also increases the efficiency of your brewhouse by eliminating kettle loss from wort that may have otherwise been left behind. Ultra Low Watt Density Elements The concave base on the BrewZilla also allowed for larger heating elements with significantly lower watt density than other breweries. When a lot of energy is coming off of a small element, the local temperature near the element can be so high that it scorches the wort and causes caramelization. Lower watt density essentially means you can produce lighter color beers that would otherwise have fallen victim to caramelization effect. It also reduces that chance of boilovers and reduces stress on the elements which extends their life expectancy. Easy Access Built-In Pump The built-in pump allows you to recirculate your wort during the mash for improved efficiency and more even temperature distribution. But it can also be used to transfer your wort from kettle to fermenter rather than relying on a gravity feed, and with the optional CIP Rotar, you can used the pump to clean your BrewZilla (or fermenter) after every use. During your brew day you’ll be able to control the pump from the RAPT Controller with a dedicated button for turning the pump on and off. Another feature you’ll find on the controller is adjusting the pump flow. This doesn’t control the actual volume of the flow (you can do that from the ball valve located on the recirculation arm), but rather cycles the pump on and off automatically based on your setting. At 100%, the pump remains on continuously. But at 80%, the pump will cycle to be on 80% of the time and off 20% of the time. This may not be a feature that every brewer thinks they need, but it’s an excellent way to avoid running the pump dry accidentally, as the time the pump is off allows recirculating wort to filter through the grain bed and back into the pump inlet. If you flip over the boiler, you’ll find the magnetic drive pump and all the plumbing is right at your fingertips. This means you don’t have to disassemble the base in order to access the pump for cleaning or maintenance if required. It also means the plumbing can be changed more easily too. For instance, the unit comes as standard with the plumbing from the pump feeding both the recirculation arm and the transfer valve, but you change this so the tap outlet bypasses the pump if you prefer. MoreBeer!'s Final Word We’ve been selling all-in-one brewing systems ever since they first hit the market, and we have to say that the Gen 4 BrewZilla is not only the most feature-packed unit ever made, it’s also offered at an incredibly competitive price point when compared to other systems. You’ll get all of the cutting edge Bluetooth technology you’d get with the Grainfather and at an exceptionally lower price tag. Plus, you get the WiFi capabilities as standard, rather than as a $100 add-on accessory. When it comes to mash recirculation, that’s yet another built-in feature on the BrewZilla, and the pump can also be used for transferring and CIP cleaning. The Foundry has a great starting price, but if you want to unlock its full potential, you’ll need to spend another $100 for the recirculation pump kit. What’s more, no other system in the same ‘weight class’ has the same grain capacity. And if the standard capacity isn’t quite enough, the BrewZilla can be easily upgraded with a Boiler Body Extension Kit and Extended Malt Pipe. When you purchase the BrewZilla, you can feel confident that you’re investing in a top shelf system and all of the critical features you’re expecting will be included. Perfect for Distillation If you want to expand your lineup of homemade libations to offer Spirits in addition to Ales & Lagers, the BrewZilla makes an excellent pot still! Add the Distillation Lid upgrade and pair it with an AlcoEngine Copper Reflux Condenser or Copper Pot Still Top. AlcoEngine Stills have been selling on the home market for years and offer some of the most affordable, beginner-friendly stills you'll find. Features: Gen 4.1 Stainless steel construction 9 gallon total capacity with a finished beer output of 5-6 gallons WiFi/Bluetooth Enabled RAPT digital temperature controller Automatic step mashing with 6 programmable stages 110-120V power and plug 12.5A Requires 20A circuit Dual heating elements (1000 watts and 500 watts) Stainless steel 1/2" ball valve for gravity draining or transferring via pump Immersion wort chiller included Stainless steel malt pipe/basket Stamped in volume markers Glass lid Adjustable lid clamps (do not use with glass lid in place - see below) Magnetic drive pump for recirculation, transfers, and cleaning Recirculation arm PPSU sight glass Bottom handle for easy lifting and pouring Rubber feet Temperature reads in °F or °C Approximately 32.75" H (with recirculation arm) x 12.5" D Recommended max. grain bill: 23.5 lbs AlcoEngine Still ready with the purchase of a Distillation Lid Pump Specs: Max Capacity: 2.9–3.1 gal/min Max Head: 4.9–6.8 ft. Poles: 2 Voltage: 110–120V-AC Frequency: 50–60Hz Power: 6 watts Current: 60 mA Speed: 2600–3000rpm Duty Cycle: Continuous Capacitor: 2µF Input/Output: 13mm barb Water Resistance: IPX2 Please note: due to patent restrictions in the United States, the malt pipe has been redesigned with one set of bottom feet. This model does not include the "two stage" malt pipe as advertised by KegLand and featured in previous MoreBeer! YouTube videos. Please Note: When removing the malt pipe to drain after mashing, it is important to do so slowly rather than in one swift pull. If the malt pipe is removed all at once when it is full of wort, it is possible for the draining wort to spray out and over the rim of the brewery through the perforated bottom. Remove the malt pipe slowly so that some of the wort can drain out before it is fully removed and set on its bottom feet. This can be done by hand on the 35L unit, but for the 65L and 100L units we highly recommend using the Pulley System for removing the malt pipe. Warning: Do not engage the adjustable lid clamps when brewing with the BrewZilla's standard glass lid. The clamps are only intended to be used with distillation lids or other metal accessories. With too much tension, it is possible for the lid clamps to break the glass lid when engaged. Warning: If you are going to use an extension cord with the BrewZilla, you must ensure that the cord is the correct gauge and properly rated to suit the power requirements of your brewery. See the reference chart below for the recommended gauge based on your unit and the length of cord you wish to use.   35L (110V) 35L (220V) 65L (220V) 100L (220V) 10 ft. 14 Gauge 14 Gauge 12 Gauge 10 Gauge 25 ft. 14 Gauge 14 Gauge 12 Gauge 10 Gauge 50 ft. 12 Gauge 12 Gauge 10 Gauge 8 Gauge     FermZilla Tri-Conical Easy-Grip Fermenter A best seller for a reason! Tons of features at an incredible cost Crystal Clear super smooth PET makes fermenting and cleaning super easy 3" Butterfly valve at bottom makes removing yeast/trub easy with the 600mL collection jar. Pressurizable for fermentation and closed transfer to your keg Includes BlowTie spunding valve kit, red & yellow carbonation caps, and floating dip tube as standard The FermZilla is the perfect option for brewers that want all the advantages of a conical fermenter without the price tag of a full-blown stainless-steel unit. It allows you to dump trub, harvest yeast, and with the addition of CO2 cylinder and regulator, you can carbonate and serve – all in one vessel! The clear PET tank allows you to visually monitor fermentation activity and is pressure rated to 2.4 Bar (34.8 psi), which means you can ferment under pressure, reducing ester and fusel alcohols in your finished beer. This also gives the ability to perform pressure transfers. If you prefer to move your finished beer to a keg or other vessel, you can do so with little to no oxygen exposure. The FermZilla Tri-Conical Easy-Grip model comes packed with accessories so you can take full advantage of this pressurizable fermenter on day one. The new stock standard includes Easy-Grip threaded lid ring, BlowTie spunding valve with integrated pressure gauge, ball lock carbonation caps for the lid and collection container, floating dip tube kit with weighted filter, volume marker graduation sticker, and adhesive thermometer. What's Included: FermZilla 27L Tank with 3" T.C. Bottom Port Easy-Grip Threaded Lid Ring Integrated Gauge BlowTie Kit Spunding Valve (0-15 psi) Silicone Dip Tube Kit with Yellow Weighted Filter and SS Float (2) Yellow Liquid Carbonation Caps (2) Red Gas Carbonation Caps Fermzilla Pressure Lid with Red PRV (35 psi) 3" T.C. Butterfly Valve 600 mL Collection Container with 3" T.C. Connection Stainless Steel Stand with Swing Handles 3" tri-clamp with gasket Graduation Sticker Adhesive Thermometer Specs: 27 L (7.1 gal) Total Volume Pressure Rated to 2.4 Bar (34.8 psi) Height in Stand - 30.2" Tank Diameter - 13.9" Diameter in Stand - 15.3" Lid & Collection Container Ports - 28 mm PCO 1881 threads Temperature Rating: When not under pressure, do not expose to liquids above 131°F When under pressure, do not expose to any temperatures above 95°F* *Please note that the temperature rating for the FermZilla tank is lower when using it under pressure. When not under pressure, it is perfectly safe to transfer wort into the tank below 131°F or to use hot liquids below this temp for cleaning. When under pressure, make sure to keep your fermentation temperature below 95°F and keep the fermenter in an environment that is below 95°F ambient. This is especially important when fermenting with kveik yeast. These strains are known to ferment hot if no temperature control is being used. Exceeding the temperature rating may compromise the tank, leading to a shorter life span or sudden failure to maintain pressure. Even with proper use, we recommend replacing the tank every two years. Please note: when using the FermZilla under pressure, you must perform a water pressure check to ensure your connections are leak proof. To do this, fill your FermZilla up with water, apply at least 15 psi pressure, and check for leaks around all caps and threads. Pressure Stress If you use the FermZilla to ferment under pressure, or you use CO2 to pressure transfer or force carbonate your finished beer, it is very important that you conduct semi-annual inspections of your tank. Even with perfect care, the FermZilla tank may show signs of wear from pressure stress over time. We recommend visually inspecting your tank for stress creases or other signs of wear once or twice a year. A hydro test should be conducted every two years, even if no signs of wear are found. The process is simple: Fill the tank to the brim with water Replace the Red PRV with a Green PRV rated to 4.5 BAR or higher Pressurize the tank to 4 BAR (58 psi) Check for leaks, then replace the Red PRV when finished If leaks or potential points of failure are found, replace the tank before you continue using pressure with your FermZilla. General Care Taking good care of your FermZilla begins with cleaning and sanitizing the unit before and after use. The tank is made from food-grade PET, which is beautifully clear, but can be sensitive to long soaks in cleaners and acid-based sanitizers. In general, we do not recommend leaving products like PBW or StarSan soaking in the tank for more than an hour. Extended soaks have the potential to degrade the PET material and shorten the lifespan of the tank.   KegLand Part number: KL47296 NOTE: FermZilla tanks are marked with a manufacturer’s “expiry date”. This does not indicate that the tank is bad after this date; it simply indicates that a hydro test may be in order. 2 years after production and every 2 years after first use, it is recommended that the tank be hydro tested to ensure the tank is holding pressure. You will also need the D1072 Green PRV to perform the test. If you do not plan to pressurize the fermenter, the test is not necessary.   FermZilla Tri-Conical 27L & 55L | User Guide

Read more less

Elevate your brewing game with the 220V Gen 4 BrewZilla. This cutting-edge system combines more power with innovative features like wireless connectivity via WiFi & Bluetooth, allowing you to heat faster while you control and monitor your brew day, ensuring precision, convenience, and exceptional beer batch after batch! WiFi / Bluetooth enabled RAPT Controller tracks your brewday and automatically uploads detailed information to the RAPT portal The top mounted RAPT Controller can be tilted upward for easy viewing, or detached from the unit to mount it on the wall or placed on your bench Mirror polished dome shaped bottom with center drain — get every last bit of wort into your fermenter while the perforated bottom screen filters out 95% of hot break and hop matter Make larger batches or higher gravity beers! BrewZilla offers the largest malt pipe capacity for units in its size range, and the Gen 4 unit has a 30% larger malt pipe compared to the previous generation Perforated bottom on the newly designed malt pipe allows for improved mash recirculation flow without sacrificing efficiency Element power percentage can be adjusted via the RAPT Controller. Go full power to heat up quickly, or dial it down so you don’t overshoot your strike water temp The built-in pump is plumbed to both the recirculation and arm and the bottom ball valve. Recirculate wort during your mash, then close the recirculation valve and pump wort to your fermenter via the bottom valve Pair with the RAPT-enabled Bluetooth Thermometer, allowing your BrewZilla to calculate a core mash temperature reading and more accurately control temperatures and mash steps More RAPT-enabled accessories are coming, and future firmware updates can be downloaded to the RAPT Controller itself over the internet WiFi/Bluetooth Enabled RAPT Controller The RAPT Controller is mounted to the top of the boiler body, allowing for easy operation when you have the unit set on the ground. The controller can be tilted upwards to give you an even better view, or it can be removed from the BrewZilla entirely if you’d prefer to mount the controller on your wall or lay it down on a workbench. From the controller, you’ll orchestrate your entire brew day. Program mash steps, dial in element power, and operate the integrated pump all from one screen. But the RAPT Controller is much more than a beautiful, full-color display switch board. Once synced to the RAPT Portal, you’ll be able to track, record and monitor your brews online. No need for handwriting notes or punching brew day details into your phone – all of the data from your brew is automatically logged to your portal profile. This information doesn’t just include your mash profile; it also captures detailed information about your element power and pump activity, opening the door for very precise repeatability. And the RAPT Portal isn’t just a digital archive for your brew days. With your BrewZilla powered on, you can control your brewery from virtually anywhere using your phone’s web browser. Not sure when you’ll be home from work or your kid’s ball game going into extra innings? No problem! Before you head out, simply log into the RAPT Portal from your phone and tell the BrewZilla to start heating your strike water. Along with remote control, the portal enables you to program alarms and push notifications for all of your boil additions. We’ve all been caught up with a side task and failed to throw in that yeast nutrient or clarifying agent at the end of the boil, but the BrewZilla has the back of even the most forgetful brewer! But wait, there’s more! In addition to WiFi connectivity, the RAPT Controller is also a Bluetooth gateway device. KegLand is currently developing various Bluetooth devices such as the Bluetooth Beacon Thermometer and other sensors which will be compatible with your brewery upon release. The RAPT Controller is able to receive information from Bluetooth Low Energy (BLE) devices, adjusting its processes based on this new stream of information while simultaneously logging it to your RAPT Portal. With the Bluetooth Beacon Thermometer, for example, you’ll be able to feed temperature readings from the top of your mash bed to the controller. The controller will then compare this reading with the main temp probe reading at the base of the kettle and adjust element cycling based on these combined readings. Finally, the RAPT Controller WiFi connectivity allows you to update the controller’s firmware with a single click. Take advantage of new features and accessories as soon as they become available by simply keeping your BrewZilla connected to your local WiFi network. And again, the WiFi is already built-in! No need to come back for an expensive add-on accessory down the road. High Capacity Malt Pipe With an approximately 23.5 lb capacity, the BrewZilla can mash nearly 50% more grain than similar sized models of the Anvil Foundry and Grainfather G30. If you want to fill your fermenter with more than a 5-gallon batch worth of wort, or brew the highest gravity beer recipes, the BrewZilla is the brewhouse for the job. And the included malt pipe is just the beginning. If you want to expand your brewery’s grain capacity even further, KegLand makes Boiler Extension Kits and Extended Malt Pipes for that very purpose. The malt pipe features a perforated section at the bottom which improves mash recirculation flow without sacrificing efficiency. Concave Base with Center Draining Leave no wort behind! The concave base with center drain means you’ll be able to extract every last drop of wort to your fermenter. If you’ve brewed in a traditional flat bottom kettle, this center drain may be a bit perplexing at first. Many brewers are used to whirlpooling after the boil to pull hop matter into the center of the kettle, then transfer out using a pick-up tube that pulls from the kettle wall in order to avoid sucking up the solids. But fear not! One of the key features of the BrewZilla is the false bottom protection screen. This screen avoids the need for doing a whirlpool, filtering wort as it transfers and blocking more than 95% of hops and hot break from getting sucked into the pump. This not only prevents blocked pump issues, it also increases the efficiency of your brewhouse by eliminating kettle loss from wort that may have otherwise been left behind. Ultra Low Watt Density Elements The concave base on the BrewZilla also allowed for larger heating elements with significantly lower watt density than other breweries. When a lot of energy is coming off of a small element, the local temperature near the element can be so high that it scorches the wort and causes caramelization. Lower watt density essentially means you can produce lighter color beers that would otherwise have fallen victim to caramelization effect. It also reduces that chance of boilovers and reduces stress on the elements which extends their life expectancy. Easy Access Built-In Pump The built-in pump allows you to recirculate your wort during the mash for improved efficiency and more even temperature distribution. But it can also be used to transfer your wort from kettle to fermenter rather than relying on a gravity feed, and with the optional CIP Rotar, you can used the pump to clean your BrewZilla (or fermenter) after every use. During your brew day you’ll be able to control the pump from the RAPT Controller with a dedicated button for turning the pump on and off. Another feature you’ll find on the controller is adjusting the pump flow. This doesn’t control the actual volume of the flow (you can do that from the ball valve located on the recirculation arm), but rather cycles the pump on and off automatically based on your setting. At 100%, the pump remains on continuously. But at 80%, the pump will cycle to be on 80% of the time and off 20% of the time. This may not be a feature that every brewer thinks they need, but it’s an excellent way to avoid running the pump dry accidentally, as the time the pump is off allows recirculating wort to filter through the grain bed and back into the pump inlet. If you flip over the boiler, you’ll find the magnetic drive pump and all the plumbing is right at your fingertips. This means you don’t have to disassemble the base in order to access the pump for cleaning or maintenance if required. It also means the plumbing can be changed more easily too. For instance, the unit comes as standard with the plumbing from the pump feeding both the recirculation arm and the transfer valve, but you change this so the tap outlet bypasses the pump if you prefer. MoreBeer!'s Final Word We’ve been selling all-in-one brewing systems ever since they first hit the market, and we have to say that the Gen 4 BrewZilla is not only the most feature-packed unit ever made, it’s also offered at an incredibly competitive price point when compared to other systems. You’ll get all of the cutting edge Bluetooth technology you’d get with the Grainfather and at an exceptionally lower price tag. Plus, you get the WiFi capabilities as standard, rather than as a $100 add-on accessory. When it comes to mash recirculation, that’s yet another built-in feature on the BrewZilla, and the pump can also be used for transferring and CIP cleaning. The Foundry has a great starting price, but if you want to unlock its full potential, you’ll need to spend another $100 for the recirculation pump kit. What’s more, no other system in the same ‘weight class’ has the same grain capacity. And if the standard capacity isn’t quite enough, the BrewZilla can be easily upgraded with a Boiler Body Extension Kit and Extended Malt Pipe. When you purchase the BrewZilla, you can feel confident that you’re investing in a top shelf system and all of the critical features you’re expecting will be included. Perfect for Distillation If you want to expand your lineup of homemade libations to offer Spirits in addition to Ales & Lagers, the BrewZilla makes an excellent pot still! Add the Distillation Lid upgrade and pair it with an AlcoEngine Copper Reflux Condenser or Copper Pot Still Top. AlcoEngine Stills have been selling on the home market for years and offer some of the most affordable, beginner-friendly stills you'll find. Features: Gen 4.1 Stainless steel construction 9 gallon total capacity with a finished beer output of 5-6 gallons WiFi/Bluetooth Enabled RAPT digital temperature controller Automatic step mashing with 6 programmable stages 220-240V power NEMA 6-30P plug Requires NEMA 6-30R receptacle Requires 11 amps from 30 amp circuit Dual heating elements (1900 watts and 500 watts) Stainless steel 1/2" ball valve for gravity draining or transferring via pump Immersion wort chiller included Stainless steel malt pipe/basket Stamped in volume markers Glass lid Adjustable lid clamps (do not use with glass lid in place - see below) Magnetic drive pump for recirculation, transfers, and cleaning Recirculation arm PPSU sight glass Bottom handle for easy lifting and pouring Rubber feet Temperature reads in °F or °C Approximately 32.75" H (with recirculation arm) x 12.5" D Recommended max. grain bill: 23.5 lbs AlcoEngine Still ready with the purchase of a Distillation Lid Pump Specs: Max Capacity: 2.9–3.1 gal/min Max Head: 4.9–6.8 ft. Poles: 2 Voltage: 220–240V-AC Frequency: 50–60Hz Power: 6 watts Current: 60 mA Speed: 2600–3000rpm Duty Cycle: Continuous Capacitor: 2µF Input/Output: 13mm barb Water Resistance: IPX2 You Will Need: 2' of H985 1/2" ID Silicone tubing for sparging and draining. To connect included Chiller: (20') of D1710 1/2" ID beverage tubing (or whatever length required, (3) H950hose clamps and (1) brass hose by thread adaptor (H508). These items come in the Wort Chiller Connection Kit, add the kit to your cart and use code ZILLAKIT at checkout. KegLand Part Number: KL27434 Please note: due to patent restrictions in the United States, the malt pipe has been redesigned with one set of bottom feet. This model does not include the "two stage" malt pipe as advertised by KegLand and featured in previous MoreBeer! YouTube videos. Please Note: When removing the malt pipe to drain after mashing, it is important to do so slowly rather than in one swift pull. If the malt pipe is removed all at once when it is full of wort, it is possible for the draining wort to spray out and over the rim of the brewery through the perforated bottom. Remove the malt pipe slowly so that some of the wort can drain out before it is fully removed and set on its bottom feet. This can be done by hand on the 35L unit, but for the 65L and 100L units we highly recommend using the Pulley System for removing the malt pipe. Warning: Do not engage the adjustable lid clamps when brewing with the BrewZilla's standard glass lid. The clamps are only intended to be used with distillation lids or other metal accessories. With too much tension, it is possible for the lid clamps to break the glass lid when engaged. Warning: If you are going to use an extension cord with the BrewZilla, you must ensure that the cord is the correct gauge and properly rated to suit the power requirements of your brewery. See the reference chart below for the recommended gauge based on your unit and the length of cord you wish to use.   35L (110V) 35L (220V) 65L (220V) 100L (220V) 10 ft. 14 Gauge 14 Gauge 12 Gauge 10 Gauge 25 ft. 14 Gauge 14 Gauge 12 Gauge 10 Gauge 50 ft. 12 Gauge 12 Gauge 10 Gauge 8 Gauge   RAPT Gen 4 BrewZilla | User Manual

Read more less

This is a replacement seal kit for all Blichmann BoilerMaker Brew Kettles. We recommend purchasing a seal kit when you purchase a BoilerMaker as they're relatively inexpensive, and are great to have on hand if you have a leak on brew day!

Read more less

This unique kettle with four tri-clamp ports was developed for the BrewBuilt electric kettle line as it requires two ports for two electric heating elements. The kettle is offered without fittings so you can rig it up with whatever accessories you see fit. Welded 1.5" tri-clamp ports for a lifetime of leak-free use 304 stainless steel construction with mirror polish finish Front and back located handles with silicone grips Induction burner compatible Notched lid provides cover while not interfering with immersion chillers, hop bags, or other accessories The BrewBuilt Pro Brewing Kettle is built for even more versatility than the standard T.C. kettle. A third and fourth tri-clamp port are offset from the front and ready to accept an electric heating element, whirlpool return valve, or any other accessory that you want to incorporate with the kettle. Handles are located at the front and back, rather than either side, saving you space when building out a horizontal system and will keep fittings pointed away from you regardless of which side you pick up the kettle from. Designed for Brewing. Built to Last. BrewBuilt brew kettles are made from 304 stainless steel and offer an unparalleled mix of features for the price. At the very top of the list are four welded-in place tri-clamp couplers that offer a lifetime of leak free use.  As you can imagine, welding in a coupler costs more than punching a hole and using a gasketed (i.e. weld-less) fitting. Welded fittings offer a permanent connection that to us is worth every penny.  The second unique feature that we absolutely love about these brew kettles is the notched lid with silicone plug.  This notch allows you so much flexibility; you can use an immersion chiller, one of our Ultimate Sparge Arms for mashing, tie off hop bags, take a temp reading during cooling, or whatever else we all can dream up.   Our T.C. kettles were designed to keep pace with the ever-evolving world of brewing technology. Tri-clamp fittings are standard fare in professional breweries, and they’ve been widely adopted in homebrewing as T.C. fermenters and pumps become more affordable and widely available. Tri-clamp fittings, also known as Tri-clover, allow you to make a sanitary connection that is free of nooks and crannies for contaminants to take hold. They are much easier to break down for cleaning compared to threaded connections, and they don’t require Teflon tape to make a watertight seal. T.C. fittings and accessories also give you the distinct advantage of being able to clean in place (CIP), so you don’t need to break down your entire system after every brew day.   This kettle comes without fittings so you can modify it with whatever tri-clamp accessories best suit your needs.   This Brew Kettle has a lot to offer... Some other features we dig include the internal volume markers from the bottom to the top - so handy for instant reads.  The silicone sleeved handles on the kettle and the lid are a cool feature to protect your hands. The tri-clad bottom with a 4mm core of aluminum sandwiched between two layers of stainless steel offers even heat distribution during the boil and also makes it a perfect choice for anyone wanting to use an induction burner.  The bottom coupler is also cool with 1/2" male threads on the outside and 1/2'' female threads on the inside.     Beefy 304 Stainless These kettles are made from 304 grade stainless.  That means you will have less corrosion issues than with a kettle made from lower grade 201 type stainless. We put these kettles through a corrosive salt water test in the MoreBeer! shop and they passed with flying colors. We also made sure the rivets and riveted handles were also made of stainless steel for a long term, trouble free life.  The 10 and 15 gallon size are made from 1.0mm thick stainless steel. The 20, 30 and 50 gallon size are made with 1.2mm stainless - that's pretty thick stuff - and you will know it when you pick one up. The included ball valve is a two piece design that allows for easy cleaning (we prefer these over 3 piece for ease of assembly) and is also made from 304 stainless.    Mirror Polish Finish The mirror polish finish isn’t just for making your Instagram feed pop! This extra slick finish is much easier to clean and sanitize than a standard brushed stainless kettle. Hop trub and other organic solids left behind after a brew day will have a hard time clinging to the interior surface and scrub away with ease.   Size Ratios and Stuff All the BrewBuilt kettles follow the recent trend to a 1.2:1 ratio where the height is 1.2 times the diameter. This is a proven commercial ratio that has been adopted in homebrewing to achieve a more consistent 10% evaporation rate during the boil.  We do like this ratio for boiling. For Mashing we would prefer a little bit shallower but that is a small compromise. Dimensions for a hot-liquor tank, if you are thinking brewing system down the road, are irrelevant as any ratio kettle will do.     Final Words With welded tri-clamp fittings, mirror polish finish, a bunch of cool features, and a solid, thick 304 stainless steel core this kettle is a pretty amazing value. Remember, if you order from MoreBeer! we ship free anywhere in the continental USA!   Features: Four welded T.C. couplers for a lifetime of leak free use Notched lid with silicone plug for flexibility 304 Stainless construction for longevity 1.0mm (10 & 15 gal) or 1.2mm (20, 30 & 50 gal) thick side walls resist denting 4mm Tri-Clad Aluminum bottom sandwiched between two layers of stainless steel for no scorching Internally etched volume markers from top to bottom for easy reading Silicone coated handles for heat protection 1.2:1 Ratio is optimal for boiling evaporation rate Lid is designed to conveniently hang from a handle  Stainless handles with stainless rivets for secure lifting Kettle ID - 23.62" Height - 28.3"    

Read more less

The Ultimate Grain to Glass Combo Pack! Get the Gen 4 BrewZilla & FermZilla Easy-Grip Tri-Conical with all the best accessories at an unbeatable price! Brew extract or all grain batches on the BrewZilla; ferment, carbonate, and serve from the FermZilla. Everything you need from Grain to Glass! Comes with all of the most highly recommended accessories for the BrewZilla, including the Neoprene Jacket to speed up heating times, Hop Spider to keep vegetal matter out of your wort, and Chilling Connection kit so you're ready to use the Immersion Chiller out of the box Includes some of our favorite accessories for the FermZilla, such as the Pressure Kit with Floating Dip Tube so you're always racking the clearest beer and the Duotight BlowTie 2 for pressure fermentations and flow control keg transfers Over $100 savings when purchasing this kit bundle compared to buying everything piece-by-piece! Also available in 110V (AG580) You can search high and low, but you won't find a better deal than the BrewZilla Ultimate Grain to Glass Combo Pack! Combo Pack Includes: BrewZilla Brewing System | Gen 4.1 | 9.25G | 220V Neoprene Jacket Hop Spider Wort Chiller Connection Kit FermZilla Tri-Conical Fermenter | Gen 3.2 | 7.1G Plastic Pressure Kit w/ Floating Dip Tube Duotight BlowTie 2 Spunding Valve Insulating Jacket Gen 4 BrewZilla All-in-One Brewing System WiFi / Bluetooth enabled RAPT Controller tracks your brewday and automatically uploads detailed information to the RAPT portal The top mounted RAPT Controller can be tilted upward for easy viewing, or detached from the unit to mount it on the wall or placed on your bench Mirror polished dome shaped bottom with center drain — get every last bit of wort into your fermenter while the perforated bottom screen filters out 95% of hot break and hop matter Make larger batches or higher gravity beers! BrewZilla offers the largest malt pipe capacity for units in its size range, and the Gen 4 unit has a 30% larger malt pipe compared to the previous generation Perforated bottom on the newly designed malt pipe allows for improved mash recirculation flow without sacrificing efficiency Element power percentage can be adjusted via the RAPT Controller. Go full power to heat up quickly, or dial it down so you don’t overshoot your strike water temp The built-in pump is plumbed to both the recirculation and arm and the bottom ball valve. Recirculate wort during your mash, then close the recirculation valve and pump wort to your fermenter via the bottom valve Pair with the RAPT-enabled Bluetooth Thermometer, allowing your BrewZilla to calculate a core mash temperature reading and more accurately control temperatures and mash steps More RAPT-enabled accessories are coming, and future firmware updates can be downloaded to the RAPT Controller itself over the internet WiFi/Bluetooth Enabled RAPT Controller The RAPT Controller is mounted to the top of the boiler body, allowing for easy operation when you have the unit set on the ground. The controller can be tilted upwards to give you an even better view, or it can be removed from the BrewZilla entirely if you’d prefer to mount the controller on your wall or lay it down on a workbench. From the controller, you’ll orchestrate your entire brew day. Program mash steps, dial in element power, and operate the integrated pump all from one screen. But the RAPT Controller is much more than a beautiful, full-color display switch board. Once synced to the RAPT Portal, you’ll be able to track, record and monitor your brews online. No need for handwriting notes or punching brew day details into your phone – all of the data from your brew is automatically logged to your portal profile. This information doesn’t just include your mash profile; it also captures detailed information about your element power and pump activity, opening the door for very precise repeatability. And the RAPT Portal isn’t just a digital archive for your brew days. With your BrewZilla powered on, you can control your brewery from virtually anywhere using your phone’s web browser. Not sure when you’ll be home from work or your kid’s ball game going into extra innings? No problem! Before you head out, simply log into the RAPT Portal from your phone and tell the BrewZilla to start heating your strike water. Along with remote control, the portal enables you to program alarms and push notifications for all of your boil additions. We’ve all been caught up with a side task and failed to throw in that yeast nutrient or clarifying agent at the end of the boil, but the BrewZilla has the back of even the most forgetful brewer! But wait, there’s more! In addition to WiFi connectivity, the RAPT Controller is also a Bluetooth gateway device. KegLand is currently developing various Bluetooth devices such as the Bluetooth Beacon Thermometer and other sensors which will be compatible with your brewery upon release. The RAPT Controller is able to receive information from Bluetooth Low Energy (BLE) devices, adjusting its processes based on this new stream of information while simultaneously logging it to your RAPT Portal. With the Bluetooth Beacon Thermometer, for example, you’ll be able to feed temperature readings from the top of your mash bed to the controller. The controller will then compare this reading with the main temp probe reading at the base of the kettle and adjust element cycling based on these combined readings. Finally, the RAPT Controller WiFi connectivity allows you to update the controller’s firmware with a single click. Take advantage of new features and accessories as soon as they become available by simply keeping your BrewZilla connected to your local WiFi network. And again, the WiFi is already built-in! No need to come back for an expensive add-on accessory down the road. High Capacity Malt Pipe With an approximately 23.5 lb capacity, the BrewZilla can mash nearly 50% more grain than similar sized models of the Anvil Foundry and Grainfather G30. If you want to fill your fermenter with more than a 5-gallon batch worth of wort, or brew the highest gravity beer recipes, the BrewZilla is the brewhouse for the job. And the included malt pipe is just the beginning. If you want to expand your brewery’s grain capacity even further, KegLand makes Boiler Extension Kits and Extended Malt Pipes for that very purpose. The malt pipe features a perforated section at the bottom which improves mash recirculation flow without sacrificing efficiency. Concave Base with Center Draining Leave no wort behind! The concave base with center drain means you’ll be able to extract every last drop of wort to your fermenter. If you’ve brewed in a traditional flat bottom kettle, this center drain may be a bit perplexing at first. Many brewers are used to whirlpooling after the boil to pull hop matter into the center of the kettle, then transfer out using a pick-up tube that pulls from the kettle wall in order to avoid sucking up the solids. But fear not! One of the key features of the BrewZilla is the false bottom protection screen. This screen avoids the need for doing a whirlpool, filtering wort as it transfers and blocking more than 95% of hops and hot break from getting sucked into the pump. This not only prevents blocked pump issues, it also increases the efficiency of your brewhouse by eliminating kettle loss from wort that may have otherwise been left behind. Ultra Low Watt Density Elements The concave base on the BrewZilla also allowed for larger heating elements with significantly lower watt density than other breweries. When a lot of energy is coming off of a small element, the local temperature near the element can be so high that it scorches the wort and causes caramelization. Lower watt density essentially means you can produce lighter color beers that would otherwise have fallen victim to caramelization effect. It also reduces that chance of boilovers and reduces stress on the elements which extends their life expectancy. Easy Access Built-In Pump The built-in pump allows you to recirculate your wort during the mash for improved efficiency and more even temperature distribution. But it can also be used to transfer your wort from kettle to fermenter rather than relying on a gravity feed, and with the optional CIP Rotar, you can used the pump to clean your BrewZilla (or fermenter) after every use. During your brew day you’ll be able to control the pump from the RAPT Controller with a dedicated button for turning the pump on and off. Another feature you’ll find on the controller is adjusting the pump flow. This doesn’t control the actual volume of the flow (you can do that from the ball valve located on the recirculation arm), but rather cycles the pump on and off automatically based on your setting. At 100%, the pump remains on continuously. But at 80%, the pump will cycle to be on 80% of the time and off 20% of the time. This may not be a feature that every brewer thinks they need, but it’s an excellent way to avoid running the pump dry accidentally, as the time the pump is off allows recirculating wort to filter through the grain bed and back into the pump inlet. If you flip over the boiler, you’ll find the magnetic drive pump and all the plumbing is right at your fingertips. This means you don’t have to disassemble the base in order to access the pump for cleaning or maintenance if required. It also means the plumbing can be changed more easily too. For instance, the unit comes as standard with the plumbing from the pump feeding both the recirculation arm and the transfer valve, but you change this so the tap outlet bypasses the pump if you prefer. MoreBeer!'s Final Word We’ve been selling all-in-one brewing systems ever since they first hit the market, and we have to say that the Gen 4 BrewZilla is not only the most feature-packed unit ever made, it’s also offered at an incredibly competitive price point when compared to other systems. You’ll get all of the cutting edge Bluetooth technology you’d get with the Grainfather and at an exceptionally lower price tag. Plus, you get the WiFi capabilities as standard, rather than as a $100 add-on accessory. When it comes to mash recirculation, that’s yet another built-in feature on the BrewZilla, and the pump can also be used for transferring and CIP cleaning. The Foundry has a great starting price, but if you want to unlock its full potential, you’ll need to spend another $100 for the recirculation pump kit. What’s more, no other system in the same ‘weight class’ has the same grain capacity. And if the standard capacity isn’t quite enough, the BrewZilla can be easily upgraded with a Boiler Body Extension Kit and Extended Malt Pipe. When you purchase the BrewZilla, you can feel confident that you’re investing in a top shelf system and all of the critical features you’re expecting will be included. Perfect for Distillation If you want to expand your lineup of homemade libations to offer Spirits in addition to Ales & Lagers, the BrewZilla makes an excellent pot still! Add the Distillation Lid upgrade and pair it with an AlcoEngine Copper Reflux Condenser or Copper Pot Still Top. AlcoEngine Stills have been selling on the home market for years and offer some of the most affordable, beginner-friendly stills you'll find. Features: Gen 4.1 Stainless steel construction 9 gallon total capacity with a finished beer output of 5-6 gallons WiFi/Bluetooth Enabled RAPT digital temperature controller Automatic step mashing with 6 programmable stages 220-240V power NEMA 6-30P plug Requires NEMA 6-30R receptacle Requires 11 amps from 30 amp circuit Dual heating elements (1900 watts and 500 watts) Stainless steel 1/2" ball valve for gravity draining or transferring via pump Immersion wort chiller included Stainless steel malt pipe/basket Stamped in volume markers Glass lid Adjustable lid clamps (do not use with glass lid in place - see below) Magnetic drive pump for recirculation, transfers, and cleaning Recirculation arm PPSU sight glass Bottom handle for easy lifting and pouring Rubber feet Temperature reads in °F or °C Approximately 32.75" H (with recirculation arm) x 12.5" D Recommended max. grain bill: 23.5 lbs AlcoEngine Still ready with the purchase of a Distillation Lid Pump Specs: Max Capacity: 2.9–3.1 gal/min Max Head: 4.9–6.8 ft. Poles: 2 Voltage: 220–240V-AC Frequency: 50–60Hz Power: 6 watts Current: 60 mA Speed: 2600–3000rpm Duty Cycle: Continuous Capacitor: 2µF Input/Output: 13mm barb Water Resistance: IPX2 Please note: due to patent restrictions in the United States, the malt pipe has been redesigned with one set of bottom feet. This model does not include the "two stage" malt pipe as advertised by KegLand and featured in previous MoreBeer! YouTube videos. Please Note: When removing the malt pipe to drain after mashing, it is important to do so slowly rather than in one swift pull. If the malt pipe is removed all at once when it is full of wort, it is possible for the draining wort to spray out and over the rim of the brewery through the perforated bottom. Remove the malt pipe slowly so that some of the wort can drain out before it is fully removed and set on its bottom feet. This can be done by hand on the 35L unit, but for the 65L and 100L units we highly recommend using the Pulley System for removing the malt pipe. Warning: Do not engage the adjustable lid clamps when brewing with the BrewZilla's standard glass lid. The clamps are only intended to be used with distillation lids or other metal accessories. With too much tension, it is possible for the lid clamps to break the glass lid when engaged. Warning: If you are going to use an extension cord with the BrewZilla, you must ensure that the cord is the correct gauge and properly rated to suit the power requirements of your brewery. See the reference chart below for the recommended gauge based on your unit and the length of cord you wish to use.   35L (110V) 35L (220V) 65L (220V) 100L (220V) 10 ft. 14 Gauge 14 Gauge 12 Gauge 10 Gauge 25 ft. 14 Gauge 14 Gauge 12 Gauge 10 Gauge 50 ft. 12 Gauge 12 Gauge 10 Gauge 8 Gauge     FermZilla Tri-Conical Easy-Grip Fermenter A best seller for a reason! Tons of features at an incredible cost Crystal Clear super smooth PET makes fermenting and cleaning super easy 3" Butterfly valve at bottom makes removing yeast/trub easy with the 600mL collection jar. Pressurizable for fermentation and closed transfer to your keg Includes BlowTie spunding valve kit, red & yellow carbonation caps, and floating dip tube as standard The FermZilla is the perfect option for brewers that want all the advantages of a conical fermenter without the price tag of a full-blown stainless-steel unit. It allows you to dump trub, harvest yeast, and with the addition of CO2 cylinder and regulator, you can carbonate and serve – all in one vessel! The clear PET tank allows you to visually monitor fermentation activity and is pressure rated to 2.4 Bar (34.8 psi), which means you can ferment under pressure, reducing ester and fusel alcohols in your finished beer. This also gives the ability to perform pressure transfers. If you prefer to move your finished beer to a keg or other vessel, you can do so with little to no oxygen exposure. The FermZilla Tri-Conical Easy-Grip model comes packed with accessories so you can take full advantage of this pressurizable fermenter on day one. The new stock standard includes Easy-Grip threaded lid ring, BlowTie spunding valve with integrated pressure gauge, ball lock carbonation caps for the lid and collection container, floating dip tube kit with weighted filter, volume marker graduation sticker, and adhesive thermometer. What's Included: FermZilla 27L Tank with 3" T.C. Bottom Port Easy-Grip Threaded Lid Ring Integrated Gauge BlowTie Kit Spunding Valve (0-15 psi) Silicone Dip Tube Kit with Yellow Weighted Filter and SS Float (2) Yellow Liquid Carbonation Caps (2) Red Gas Carbonation Caps Fermzilla Pressure Lid with Red PRV (35 psi) 3" T.C. Butterfly Valve 600 mL Collection Container with 3" T.C. Connection Stainless Steel Stand with Swing Handles 3" tri-clamp with gasket Graduation Sticker Adhesive Thermometer Specs: 27 L (7.1 gal) Total Volume Pressure Rated to 2.4 Bar (34.8 psi) Height in Stand - 30.2" Tank Diameter - 13.9" Diameter in Stand - 15.3" Lid & Collection Container Ports - 28 mm PCO 1881 threads Temperature Rating: When not under pressure, do not expose to liquids above 131°F When under pressure, do not expose to any temperatures above 95°F* *Please note that the temperature rating for the FermZilla tank is lower when using it under pressure. When not under pressure, it is perfectly safe to transfer wort into the tank below 131°F or to use hot liquids below this temp for cleaning. When under pressure, make sure to keep your fermentation temperature below 95°F and keep the fermenter in an environment that is below 95°F ambient. This is especially important when fermenting with kveik yeast. These strains are known to ferment hot if no temperature control is being used. Exceeding the temperature rating may compromise the tank, leading to a shorter life span or sudden failure to maintain pressure. Even with proper use, we recommend replacing the tank every two years. Please note: when using the FermZilla under pressure, you must perform a water pressure check to ensure your connections are leak proof. To do this, fill your FermZilla up with water, apply at least 15 psi pressure, and check for leaks around all caps and threads. Pressure Stress If you use the FermZilla to ferment under pressure, or you use CO2 to pressure transfer or force carbonate your finished beer, it is very important that you conduct semi-annual inspections of your tank. Even with perfect care, the FermZilla tank may show signs of wear from pressure stress over time. We recommend visually inspecting your tank for stress creases or other signs of wear once or twice a year. A hydro test should be conducted every two years, even if no signs of wear are found. The process is simple: Fill the tank to the brim with water Replace the Red PRV with a Green PRV rated to 4.5 BAR or higher Pressurize the tank to 4 BAR (58 psi) Check for leaks, then replace the Red PRV when finished If leaks or potential points of failure are found, replace the tank before you continue using pressure with your FermZilla. General Care Taking good care of your FermZilla begins with cleaning and sanitizing the unit before and after use. The tank is made from food-grade PET, which is beautifully clear, but can be sensitive to long soaks in cleaners and acid-based sanitizers. In general, we do not recommend leaving products like PBW or StarSan soaking in the tank for more than an hour. Extended soaks have the potential to degrade the PET material and shorten the lifespan of the tank.   KegLand Part number: KL47296 NOTE: FermZilla tanks are marked with a manufacturer’s “expiry date”. This does not indicate that the tank is bad after this date; it simply indicates that a hydro test may be in order. 2 years after production and every 2 years after first use, it is recommended that the tank be hydro tested to ensure the tank is holding pressure. You will also need the D1072 Green PRV to perform the test. If you do not plan to pressurize the fermenter, the test is not necessary.   FermZilla Tri-Conical 27L & 55L | User Guide

Read more less

The 55 gallon BoilerMaker™ G2 is a no compromise premium brew pot packed with standard features like a patent pending linear flow drain valve that can be oriented in any direction and disassembles in seconds for cleaning.  From the sleek easy to clean surface finish, to the cool touch custom molded grips, durable easy to read level gauge, snap-in drain tube, the informative BrewMometer™ and broad suite of accessories like our patented Button Louver™ false bottom, patented HopBlocker™ and AutoSparge™, this pot defines awesomeness.  The BoilerMaker™ G2 is clearly in a class of its own.  Imported pot, assembled in USA with additional USA components.  Lifetime limited warranty. All the items you need come standard, installed, and ready to use on the G2 Brew Pot: Heavy gauge, 304 single piece, deep drawn, weld-free American made construction will turn this pot into a family heirloom* Blichmann Engineering was the innovator of the 1.2 height to diameter ratio not the imitator!  All of our pots perform consistently and flawlessly with homebrewers in mind Patent pending parabolic valve provides linear flow for unparalleled flow control. Built in 90 degree outlet can be oriented at any angle to make hose routing simple and kink free.Cool touch silicone grip makes handling under fire easy. Fixed angle BrewMometer™ with their unique patented brewing dialface - the ultimate in brewing convenience Improved surface finish hides finger-prints and cleans impeccably.  Sleek brush on the outside and a silky smooth satin finish on the inside. Standard heavy-duty borosilicate glass level gauge never clouds or scratch. Features rugged stainless steel guard with engraved volume graduations, cleaning brush and clean-out ports.  Much easier and more accurate than internal graduations.  It will also act as a mash manometer and warn you of impending stuck mashes! Exclusive snap-in dip tube design installs without tools and drains to within 3/8” of bottom! Cool touch high impact glass filled nylon handles are durable, comfortable, and cool to the touch. Stepped bottom on pot supports mash screen and virtually eliminates sidewall shunting. A great way to start with high-quality equipment equipped with all the options. Please Note: 30 & 55 gallon G2 Boilermakers will come equipped with G1 Lids (see image for details)

Read more less

What puts the KOMOS Olympus Kegerator in a league of its own? Spacious all-stainless interior can hold up to TWENTY 5-gallon Slimline Torpedo homebrew kegs Commercial-level refrigeration components provide powerful cooling capacity Double-paned glass doors are self-closing and come with lock & key Stainless steel forward-sealing faucets offer a huge upgrade over common chrome plated brass taps Choose from the classic stainless or upgraded stainless flow control model Faucets mount to high-quality stainless steel towers, rather than cheap chrome plated towers Interior fan diverts cold air up into the towers to keep your beer lines cold and reduce foaming EVABarrier double walled draft tubing protects your beer against oxidation Duotight push-to-connect fittings make assembly a breeze Included KOMOS Dual Gauge CO2 Regulator maintains consistent pressure and is easily adjusted The KOMOS Olympus Kegerator was engineered with commercial use in mind, and easily stands up to the rigorous demands of a professional environment. That being said, this absolutely gorgeous kegerator will only enhance whatever room it finds itself in, whether that's the local taproom or your home bar. Swinging glass doors open up to an incredibly spacious interior with enough room to fit up to twenty 5-gallon Slimline Torpedo kegs or Pepsi-style Ball Lock Corny kegs, or five full sized Commercial Sanke Kegs. If you don't plan on packing it full of kegs, adjustable-height wire racks provide the perfect spot to store bottles and cans. And since they'll be on beautiful display thanks to interior lighting, no more standing with the fridge door open to see what there is to drink! Whether you choose the single, double, triple, or quad tap configuration, you'll receive NukaTap stainless steel faucets, the newest in forward-sealing faucet design. Stainless faucets are a huge upgrade over the chrome-plated brass faucets commonly included with other kegerators, and you'll quickly recognize the quality of a forward-sealing beer faucet compared to the standard taps seen at your local tavern or in-law's mancave. Rather than a chrome plated plastic towers, the NukaTap faucets are mounted to stainless steel towers that remain cool before, during, and after each pour thanks to tower fan diverters that recirculate cold air within the kegerator and blows it up into the towers to keep your beer lines cold and reduce foaming. From keg to faucet, your beer will pass through EVABarrier draft lines, a premium double-walled tubing designed to protect against beer oxidation. And with Duotight push-to-connect fittings, you'll have your lines connected in a snap with no need to force the tubing over barb fittings or fiddle with hose clamps. Other features you'll love about the KOMOS Olympus Kegerator include its powerful cooling capacity so your beer will remain cold no matter how many kegs you're storing, high-quality easy to use digital thermostat, stainless steel interior with rubber floor mat, rolling casters, and the included KOMOS Dual Gauge CO2 regulator Forward-sealing Stainless Faucets and Towers All KOMOS kegerators come with NukaTap stainless steel forward-sealing faucets and a stainless steel draft tower. While other kegerator brands include basic, chrome-plated faucets and ABS plastic draft towers to reduce cost, KOMOS includes these premium upgrades as standard. Forward-sealing means that while in the closed position the faucet will keep beer in it instead of draining out. This keeps the internal parts from getting sticky and reduces the chance of off flavors transferring to your beer while you pour. Most other kegerators on the market will include the cheapest, rear-sealing chrome-plated beer faucets that you'd find at any dive bar. KOMOS kegerators include not only a faucet that features superior pour technology, but made from stainless steel which won't corrode over years of use. Choose from the classic forward-sealing faucet model or the upgraded flow control model that allows you to dial in the flow rate of the beverage you're dispensing. The flow control faucet is a great option for users that often switch between beer styles with different carbonation levels. No need to rebalance your lines or play with your regulator settings. Instantly make adjustments as you pour to dial in the flow rate. This is also a super convenient feature for when you want to grab a quick growler on your way out. By dialing back the flow rate, you can gently fill your growler so CO2 stays in solution and your beer doesn't pour flat when it comes time to share. Click here to learn more about the Classic and Flow Control faucet models. Duotight Fittings & EVABarrier Draft Tubing Duotight and EVABarrier have revolutionized how you connect draft line, and our kegerators come standard with both. We love Duotight push-in fittings for their quick connection, reliable seal, and versatility. Setting up and connecting draft line has never been easier -- no more hose clamps or heating water to soften tubing! Each kegerator comes with Duotight fittings for the tower shanks, regulator, and for splitting gas lines (double & triple tap only). We recommend adding Duotight fittings to use for your keg connections as well. Depending on whether you'll be serving from homebrew kegs or commercial sanke kegs, you'll need two DUO106 or two DUO104 per line. EVABarrier tubing has been engineered with protection in mind and is both PVC-free and BPA-free. This double walled tubing offers superior protection against oxidation, CO2 loss, and microbial growth. EVA tubing is the future of draft line for professional applications, and now your kegerator will feature the same first-class tubing. KOMOS Regulator The included high-quality KOMOS CO2 regulator maintains consistent pressure and features a blow-off PRV with pull ring for safety and to relieve pressure, rubber coated gauges, and a hand knob for easy adjustment. Many kegerator brands will include the cheapest regulator they can find, and while these regulators may work OK out of the box, they will eventually show signs of pressure creep which can lead to foamy beer and other issues with your draft system. Rather than have you rely on a regulator that is "just OK", KOMOS kegerators include their own premium dual gauge regulator with highly accurate precision diaphragm and heavy-duty steel gauges. Included with your kegerator package is a Duotight fitting that attaches to the regulator for an easy, solid, push-to-connect connection with your gas line. Added Features All of that cooling power doesn't just keep your kegs cold thanks to the interior tower fan which blows cold air up into your towers to reduce foaming issues. The Olympus also comes standard with the KOMOS dual gauge CO2 regulator, which is super beefy and consistent in delivering accurate pressures. Most Chinese-made regulators experience creep where the pressure increases over time. The KOMOS regulator is by far the best CO2 regulator we have seen made in China. The recessed drip trays feature a built-in drain so spilled beer won't be hanging around in front of the draft towers. Tubing comes pre-installed and runs to an exterior bottom outlet that can be routed to a floor drain, or you can cut the tubing shorter on the inside and let the beer drain into a bucket. For home setups where a floor drain isn't an option, keeping the bucket inside the kegerator will keep it away from pesky fruit flies and other pests. And to keep everything in tip-top shape, the drip dray's grill is removable anytime you want to wipe down the reservoir or wash the grill. Feature Summary: Stainless Steel Air Cooled Towers Stainless Steel NukaTap Forward-Sealing Faucets Choose faucet model and number of taps above Duotight Fittings make connecting draft lines a breeze Easy to use digital temperature controller Robust KOMOS Dual Gauge Regulator included Commercial grade compressor uses R290 refrigerant Beautiful stainless steel countertop style surface All stainless steel exterior and interior with rubber floor mat Recessed countertop style drip tray with built-in drain Adjustable-height Rubber-coated stainless steel bottle racks Heavy duty rolling casters come standard Front and side facing ventilation for maximum cooling efficiency Lock & key to keep your precious beverages protected Interior lighting can be switched On/Off from the outside Includes EVABarrier beer and gas tubing Beverage line measures 4mm ID x 8mm OD 1 x 1.7m length of line per tap Gas line measures 5mm ID x 8mm OD 1 x line of varying length depending on number of taps (2, 2.5, or 3m) 4 Tap towers includes uncut rolls of bev & gas line We recommend cutting bev lines to 1.7-2m lengths (5.5-6.5 ft.) Gas lines can be cut to whatever length best suits your needs Duotight adapters for draft shank and regulator connections Duotight tee fittings for splitting gas lines (2-tap tower and higher only) You will need to purchase keg connections depending on whether you are serving commercial sanke, ball lock corny, or pin lock corny For ball lock and pin lock disconnects we recommend DUO106 For commercial sanke keg couplers we recommend DUO104 ETL Certified Specifications: 90.875" Wide 27.75" Deep 36.75" Tall (fridge only) 40" Tall with Caster Wheels +15.75" with 4-Tap Tower +12.75" with 1 to 3-Tap Tower 115V - 60 hz 2.88 Amp draw Internal Dimensions: 78" Wide 21.75" Deep 29.25" Tall Door Frames - 28.75" H x 21" W What Fits: 5 Gal. Slimline Torpedo Keg - 20 5 Gal. Ball Lock Cornelius Keg (Corny Keg) - 20 7.75 Gal. Quarter Barrel Keg (Pony Keg, Stubby Quarter) - 5 15.5 Gal. Half Barrel Keg (Full Size Keg) - 5   When choosing the number of taps you want, here is the tower configurations you'll receive. Taps Tower 1 Tower 2 2-Tap Single Single 3-Tap Single Double 4-Tap Double Double 5-Tap Double Triple 6-Tap Triple Triple 7-Tap Triple Quad 8-Tap Quad Quad   Detailed instructions for operating the temperature controller are included with the kegerator. For instructions on assembling the tower & line kits, please see pages 7-10 in the manual below. Please note: The optimal conditions for this unit are an indoor environment with temperatures not exceeding 86°F and 55% relative humidity. If used outdoors or in an environment exceeding these conditions, note that the unit will operate for longer durations, and defrost cycles will vary based on temperature and humidity levels.

Read more less

PLEASE NOTE: The supplier of this product has temporarily halted shipments to addresses within the state of California. If you are a CA resident, please note your order will not be fulfilled and will ultimately be canceled. We hope to have this issue resolved with the supplier as soon as possible.   Thanks to the 70L (18.5 gal) capacity, homebrewers can produce more beer to share or commercial breweries now have a unit that's small enough for pilot testing. It also has a smart controller with built-in wireless connectivity and mobile app integration for step-by-step remote-controlled brewing. The G70² gives you everything you need in one compact package that can be used virtually anywhere. Please Note - this system comes standard with a NEMA 6-15P plug, and requires access to a 220v-240v power supply. New Features on the G70²: The G70² features a perforated grain basket and the sight glass is now integrated into the recirculation pipework. The new basket design provides an improved brewing experience with no top plate or additional pipework required, making for an even more efficient mash and an easier clean. Perforated grain basket for an improved brewing experience with no top plate or additional pipework required. Integrated sight glass is now a part of the recirculation pipework for easy volume reading. 70L of innovation, consistency and power have helped to create one of our most compelling systems to date. The inherent strength and safety capabilities of the G70² are matched by its bold, contemporary look and new smart brewing technologies. From the creators of the original award-winning all-grain brewing system, the Grainfather G70² represents the next level in brewing equipment. We’ve stepped up our game to bring you a smarter brewing system with a larger 18.5 gal capacity, improved design, wireless control, app integration and the same Grainfather signature quality guarantee. Whether you're a homebrewer looking to raise the stakes or a commercial brewery looking to bring authenticity back to your pilot batches, the G70² is your true brewing companion. It gives you everything you need in one compact package that can be used virtually anywhere. Features: Two-stage false bottom. The conical base allows a false bottom with an inner collar to sit in the recess of the base. Early testers used 21 oz of hops and saw full flow through the pump. This is very effective. Bespoke 3.2 kWh concealed conical heating element. Make the most of the power available. The element covers around 80% of the base and is mounted using a thermal paste rather than braised. This moves the heat efficiently upwards, minimizing the loss of heat to areas where it’s not needed. As it’s spread in a wide area, hot spots and scorching are very unlikely. Also, most solids settle on the false bottom, so they won’t touch the elements. As it’s concealed, it makes cleaning easy too. Integrated sight glass for easy volume readings during sparging. Instead of trying to judge the level of your preboil, you can easily sparge until you reach preboil volume. It’s also easy to clean after every brew. The sight glass cap can be replaced with the sight glass cleaning barb to easily recirculate a cleaning solution. Bottom drain below the false bottom means minimal dead space. High temperature, high flow rate, food-grade pump. With an 2.1 gal per minute flow rate, you can transfer your brew efficiently and safely. Heavy duty handles on the outside of the G70² unit. Convenient side entry recirculation. Rather than up and over, the G70² has a built in port on the side of the unit. If the pump is accidentally switched on, the wort will be safely directed back into the boiler. New rolled edge, mash plates and hop filter for increased strength and easy set up. There’s no more silicone seals, as the plates now have a smooth finish, making them more robust, hard-wearing and easy to install. Compared to the G30, the G70² is wider but not that much taller. Comparatively, the draining is still quick from the basket and there’s less likelihood of stuck sparges as the draining surface area is bigger. Safety aspects including locked in support ring, heavy duty, no slip brackets on the grain basket and protection from knocking the ball valve open. Automatic heat sensors and safety cut-out for dry boil protection. Color LCD controller screen with magnetic mounting for easy viewing from all angles and manual control. Glass lid with handle. Ball valve for sampling/draining. This runs in line with the pump so it’s particularly helpful when draining the cleaning water. The water runs out quickly, emptying the unit in no time. Huge Wort Chiller included. Despite the volume being more than double, cooling times remain around the same as the G30 thanks to a more powerful pump, efficient false bottom and bigger wort chiller to match the wider unit. The large size means it needs to be positioned away from the G70², however this is made easy with longer silicone tubing attached as standard. Lifting bar included with winch lifting hook. Use the bar for a two person lift or with a stable winch system for individual brewers to lift the grain basket. Large dual-stage hop filter provides a large surface area to allow for a hopping rate of up to 3.3 lbs, which also reduces pump load and blockages. Robust stainless steel body and excellent build quality. Specifications: 304 Grade stainless steel body 220 - 240V 18 Gal Capacity Max Grain Bill: 35 lbs Min Grain Bill: 18 lbs Powerful high flow pump: 15W

Read more less

Complex Cereal Profile: Delivers a nuanced palate of fresh grain, dough, and golden bread with sweet cereal notes and a subtle nuttiness. Streamlined Brewhouse Performance: Engineered with low modification and a 37.0–44.0 Kolbach Index to ensure easy lautering across all lager styles and brewing regimens. Usage: Up to 100% of your grain bill 1.5 - 1.8 L - Rahr To Thee!™ Pils is a versatile North American pilsner malt produced in Alix, Alberta. Designed in collaboration with industry experts, it offers the perfect balance of performance and flavor for any lager-centric brewhouse. Ideal For: Classic continental lagers, American craft lagers, and all-malt pilsners. Performance: A Kolbach Index of 37.0 - 44.0 ensures smooth, trouble-free lautering in any brewing setup. Brewing Profile: Low color and low modification for precise control over the finished beer. Tasting Notes: A rich aromatic blend of dough, golden bread, and sweet cereal with a light nutty finish. Malt Specification: Color °L - 1.5 - 1.8 Moisture % - max. 4.5 Extract fine % dm - min. 79.5 Protein Total - 11.5 max Diastatic Power >110 L Usage Rate - Up to 100%  

Read more less